Search results for "IRRADIATION"
showing 10 items of 1012 documents
About complexity of the 2.16-eV absorption band in MgO crystals irradiated with swift Xe ions
2020
Abstract The precise study of the accumulation and subsequent thermal annealing of the defects responsible for the complex absorption band around 2.16 eV, being under discussion in the literature for a long time, has been performed in highly pure MgO single crystals exposed to 0.23-GeV 132Xe ions with a fluence of Φ = 5 × 1011 − 3.3 × 1014 ions/cm2. Three Gaussian components with the maxima at 2.16, 2.02 and 2.40 eV have been considered as a measure of so-called D1, D2 and D3 defects. Similar to the F and F+ centers, the concentration of these defects increases at high fluences without saturation marks, thus confirming their radiation-induced nature (involvement of novel Frenkel defects). T…
Influence of the e-beam irradiation and photo-oxidation aging on the structure and properties of LDPE-OMMT nanocomposite films
2012
Abstract In this paper two systems, polyethylene (LDPE) and polyethylene/commercial organo-modified montmorillonite (LDPE/OMMT) nanocomposite, were subjected to e-beam irradiation at different doses and both the molecular modifications and mechanical properties have been investigated through solubility, FT-IR, calorimetric and tensile tests. Moreover, in some of the irradiated systems photo-oxidation aging was performed and its effects were studied. The results show an enhancement with irradiation of the positive effect of the nano-filler loading, related to the increase of the mechanical properties, due to the increase of the nano-filler polymer interaction. Nevertheless calorimetric and F…
Stimulated luminescence of AlN ceramics induced by ultraviolet radiation
2001
Abstract Properties of thermally stimulated luminescence (TL) and optically stimulated luminescence (OSL) of the ceramic material AlN-Y 2 O 3 have been studied after exposure to ultraviolet radiation (UVR). The dosemeter material Al 2 O 3 : C has been used for comparative measurements. The spectral sensitivity of the samples has been studied and compared with spectral effectiveness of the UVR-induced biological processes. It has been shown that a very high yield and linear dose response characterise the UVR-induced TL from AlN-Y 2 O 3 . Although lower than the TL, the OSL signal from UV-exposed AlN-Y 2 O 3 is still higher than that of Al 2 O 3 : C in a broad spectral region. The possibilit…
Localised transitions in luminescence of AlN ceramics
2014
Abstract The photoluminescence (PL) and thermoluminescence (TL) properties of AlN ceramics revealed under UV irradiation are determined mainly by oxygen-related centres, giving rise to the UV (around 3.18 eV) and the Blue (2.58 eV) bands. It was found that the UV irradiation-generated donor–acceptor pairs (DAPs), responsible for the UV emission band, are randomly distributed with regard to separation distance. Luminescence properties of AlN are interpreted basing on the model of localised recombination involving electron tunnel transitions from the excited state of D to the ground state of A, proposed by Jain et al. (2012) . The observed features of PL, afterglow and TL of AlN ceramics are …
Watch glasses exposed to 6 MV photons and 10 MeV electrons analysed by means of ESR technique: A preliminary study
2011
Abstract In this work we report a case study of the ESR response of watch glasses exposed to 6 MV photons and to 10 MeV electrons. The choice of watch glasses is justified by the fact that watch glasses are very close to the exposed individual. For both types of radiation beams, the absorbed doses belong to the range between 1 and 20 Gy. The samples have been irradiated in water-equivalent plastic phantom with a linear accelerator used for radiotherapy. After exposure watch glass samples have been cut in small strip-shaped pieces with suitable size to be put into the quartz tube for ESR measurements. The signal induced by radiation (RIS) lies in the g ∼ 2 region and must be discriminated fr…
The influence of the processing temperature on gamma curing of epoxy resins for the production of advanced composites
2007
Abstract Gamma radiation curing of an epoxy monomer, in the presence of an iodonium salt, as initiator, is studied. Systems have been polymerized at the same irradiation dose and dose rate and at different processing temperatures. The experimental results show that all the irradiated materials exhibit a latent reactivity, undergoing toward an increase of crosslinking density if they are thermally cured after irradiation. The results indicate that the processing temperature affects both the crosslinking density after irradiation and the sensibility to the post-irradiation thermal treatment.
A practical and transferable methodology for dose estimation in irradiated spices, based on thermoluminescence dosimetry
2008
Abstract The thermoluminescence technique is recommended by the European Committee for Standardization for the detection of irradiated food containing silicates as contaminants. In this work, the applicability of the thermoluminescence technique as a quantitative method to assess the original dose in irradiated oregano was studied; the additive-dose method was used, with reirradiation doses up to 600 Gy. The proposed new procedure allows to clearly discriminate irradiated from unirradiated samples, even after one year storage, and it gives an acceptable estimation of the original dose; the overall modified procedure requires only one day to be completed.
Time-resolved optical absorption in YAlO3 crystals
2004
Abstract The present work is devoted to the investigation of transient absorption (TA) induced by a pulsed electron beam (E=250 keV ) in pure and doped YAlO3 (YAP) single crystals. The nature of centers responsible for TA is discussed.
Electron beam induced polymerisation of MMA in the presence of rubber: a novel process to produce tough materials
2002
Abstract PMMA-rubber blends are formed through electron beam induced in situ polymerisation. The influence of rubber nature and irradiation dose has been investigated through mechanical tensile tests, solubility analysis and the results were related to material structure investigated through atomic force microscopy. Some blend formulations present a significant increase of ductility with respect to pure PMMA, without a dramatic decrease of modulus, yield stress and stress at break values. The results are interpreted on the basis of the criterion of the critical inter-particle thickness.
Cathodoluminescence of oxyfluoride glass-ceramics
2013
Abstract Tb, Ce, Eu activated oxyfluoride glass-ceramics with the composition SiO2 · Al2O3 · Li2O · LaF3 have been studied by cathodoluminescence (CL). We compared CL intensities and decay times of the Tb, Ce, Eu activated glass-ceramic samples and observed that the Tb activated sample has the most intense luminescence, but the Ce activated sample has the shortest decay times. Induced optical absorption and thermostimulated luminescence have been observed after X-ray irradiation of samples.