Search results for "ITC"
showing 10 items of 898 documents
50 mJ/30 ns FTIR Q-switched diode-pumped Er:Yb:glass 1.54 μm laser
2001
Abstract 50 mJ Q-switched output at 30 ns pulse duration was demonstrated with a transversely diode-pumped bulk Er 3+ :Yb 3+ :glass 1.54 μm laser system of uncomplicated and compact design, using a piezoelectrically driven FTIR shutter. In long-pulse operation, 360 mJ output was obtained for 2.65 J incident optical pump energy. Maximum optical slope efficiencies of 20.5% and 5.4% were measured in long-pulse and Q-switched operation, respectively. Optimum Q-switch timing was studied taking into account the Yb 3+ →Er 3+ energy transfer process and was correlated with free-running delay parameters.
A compact and portable laser-induced breakdown spectroscopy instrument for single and double pulse applications
2008
Abstract We present LIBS experimental results that demonstrate the use of a newly developed, compact, versatile pulsed laser source in material analysis related to art and archaeological applications in view of research aiming at the development of portable LIBS instrumentation. LIBS qualitative analysis measurements were performed on various samples and objects, and the spectra were recorded in gated and non-gated modes. The latter is important because of advantages arising from size and cost reduction when using simple, compact spectrograph-CCD detection systems over the standard ICCD-based configurations. The new laser source exhibited a very reliable performance in terms of laser pulse …
Doubly active Q switching and mode locking of an all-fiber laser
2009
Simultaneous and independent active Q switching and active mode locking of an erbium-doped fiber laser is demonstrated using all-fiber modulation techniques. A magnetostrictive rod attached to the output fiber Bragg grating modulates the Q factor of the Fabry-Perot cavity, whereas active mode locking is achieved by amplitude modulation with a Bragg-grating-based acousto-optic device. Fully modulated Q-switched mode-locked trains of optical pulses were obtained for a wide range of pump powers and repetition rates. For a Q-switched repetition rate of 500 Hz and a pump power of 100 mW, the laser generates trains of 12-14 mode-locked pulses of about 1 ns each, within an envelope of 550 ns, an o…
Efficient pulsed 946-nm laser emission from Nd:YAG pumped by a titanium-doped sapphire laser
2008
Efficient pulsed room-temperature laser emission at 946 nm is obtained from a Nd:YAG rod pumped by a Ti-doped sapphire laser in the free-running mode. Three bonded YAG rods of 3-mm diameter with different Nd concentrations and active lengths were tested. A maximum output energy of 83.5 mJ at 3 Hz was obtained with a slope efficiency of 32.3% in an end-pumping configuration.
Er:YAG laser giant-pulse generation
2002
Three possibilities of mid-infrared Er:YAG lasers Q-switching were investigated: mechanical and two electro-optical ones. The mechanical method of Q-switching was proved by using of a rotating mirror placed inside the resonator; Pockels or Kerr cells were used for the electro-optical Q-switching. The Pockels cell was constructed on the basis of the Brewster angle cut LiNb03 crystal; the Kerr cell used a ceramic PLZT material. In all the three cases the Er:YAG laser resonator was plan parallel and it consisted of the rear copper mirror and output coupler with 50-70% reflectivity. The Er:YAG crystal was pumped by one xenon flashlamp in a single elliptical silver coated cavity. The generated g…
Compact acousto-optic multimode interference device in (Al,Ga)As.
2020
Multimode interference (MMI) devices are key components in modern integrated photonic circuits. Here, we present acoustically tuned optical switches on an (Al,Ga)As platform that enable robust, compact and fast response systems improving on recently demonstrated technology. The device consists of a 2 × 2 MMI device fine-tuned in its center region by a focused surface acoustic wave (SAW) beam working in the low GHz range. In this way, we can tune the refractive index profile over a narrow modulation region and thus control the optical switching behaviour via the applied SAW intensity. Direct tuning of the MMI device avoids losses and phase errors inherent to arrayed waveguide based switches,…
Characterization of thermo-optical 2×2 switch configurations made of Dielectric Loaded Surface Plasmon Polariton Waveguides for telecom routing archi…
2012
We report on the characterization of thermo-optic switch structures based on Dielectric Loaded Surface Plasmon Polariton Waveguide for high data bit rate transfer. Performances are extracted by Leakage Radiation Microscopy and compared to numerical results.
Q -switched and modelocked all-fiber lasers based on advanced acousto-optic devices
2011
The interest in all-fiber lasers is stimulated by the inherent advantages they have over bulk lasers in aspects such as heat dissipation and robustness. The performance of Q-switched and modelocked fiber lasers can benefit enormously from the development of all-fiber configurations. A fiber laser with strictly all-fiber components can fulfil the requirements of mechanical stability, low maintenance, enhanced power efficiency, simplified assembly process, and low cost. In this framework, recent developments infiber acousto-optic devices are reviewed that have demonstrated new possibilities for actively Q-switched distributed feedback fiber lasers, modelocking lasers and doubly active Q-switc…
Digital video-electrochemistry (DVEC) to assess electrochromic materials in the frequency domain: RGB colorimetry impedance spectroscopy
2021
Abstract This work is the first one allowing the characterization of electrochromic devices simultaneously at various parts on their surface and different rates of color change. We describe a new proficient and affordable methodology for reporting electrochromic parameters such as coloration efficiency, optical contrast, and switching time based on the use of digital video-electrochemistry (DVEC) in the ac regime, namely RGB colorimetry impedance spectroscopy. Simultaneously with the electrochemical impedance spectroscopy, the RGB color changes of an electrochromic electrode were recorded by a CCD digital camera at 120 digital images per second. In such conditions, RGB electrochromic change…
Predictive dead time controller for GaN-based boost converters
2017
A dynamic dead time controller is presented, specifically intended to operate in synchronous boost converters based on GaN field-effect transistor switches. These transistors have a reduced stored charge with respect to silicon metal–oxide–semiconductor field-effect transistors with similar breakdown voltage and series resistance, and can operate at higher frequencies with reduced switching losses. On the other hand, the voltage drop in reverse conduction is typically more than doubled with respect to silicon devices resulting in relevant power losses during the free-wheeling phases. Therefore, dynamic control of dead time can be profitably applied even in converters operating in the tens o…