Search results for "Impact strength"

Processing and mechanical properties of recycled PVC and of homopolymer blends with virgin PVC

1996

Mechanical and processing properties of recycled polyvinylchloride (PVC, from bottles and pipes) were compared with those of virgin pipe grade PVC. Blends of recycled and pipe grade PVC were also prepared and characterized. It was found that the particle size and the restabilization of the recycled PVC are the two main points to be considered for obtaining virgin/recycled PVC blends with uniform and good mechanical properties. In general, recycled PVC not only does not significantly reduce the modulus and tensile strength, but also improves the impact strength and processing behavior of pipe grade virgin PVC. Only the thermomechanical resistance is slightly lowered. The latter points hold, …

Tensile strength and impact strength of color modified acrylic resin reinforced with titanium dioxide nanoparticles

2017

Background Poor mechanical properties are among the main limitations of acrylic resins. Addition of titanium dioxide (TiO2) nanoparticles to acrylic resin has been shown to improve its mechanical properties with an adverse effect on its color. Thus, this study sought to assess the tensile and impact strength of a color modified heat cure acrylic resin reinforced with TiO2 nanoparticles. Material and Methods In this in vitroexperimental study, 1wt% TiO2 nanoparticles were added to SR Triplex Hot heat-cure acrylic resin powder and mixed. Pigments and color fibers were also added and 18 samples were fabricated of this paste for tensile and impact strength testing (n=9) according to ISO5271. Ei…

Effect of adding wood flour to the physical properties of a biodegradable polymer

2008

Wood flour/polymer composites (WPC) gained a significant interest during the last decades, due to several advantages related to the use of a natural-organic filler rather than an inorganic-mineral one. However, most of the studies have been performed on composites based on polyolefin matrices. A further step is the use of biodegradable polymers instead of traditional ones. In this work, wood flour (WF), under the form of short fibers, with two different sizes (coarse and fine) was added to a corn starch based biodegradable polymer of the Mater-Bi family. The effect of WF size, WF content, thermal treatment on the mechanical properties was investigated. The tensile mechanical tests showed an…

Preparation and mechanical properties of intercalated PP/OMMT nanocomposites

2007

The preparation of polymer nanocomposites by melt compounding polypropylene (PP) with organically modified montmorillonite using maleic anhydride modified PP as compatibilizer is described. Compositions with organomontmorillonite content 0, 5, 10 wt.% were prepared and tested. Data on the influence of organomontmorillonite content on the tensile stress?strain curves, elastic modulus, strength, and ultimate elongation of the nanocomposites are obtained. The concentration dependences of elastic properties of materials with differently oriented plate like nanoparticles analyses taking into account hierarchical structure features of nanocomposites is considered. Theoretical analysis results are…

“Effect of Filler Type and Processing Apparatus on the Properties of the Recycled “Light Fraction” from Municipal Post-Consumer Plastics”

2001

Plastic waste or scraps are generated from two main sources: industrial wastes and post-consumer wastes. By using the flotation method, generally two fractions are obtained from municipal post-consumer wastes: a light fraction, floating on water, and a heavy fraction. The former is essentially made of low and high density polyethylene—LDPE, HDPE—and polypropylene—PP; the heavy fraction is formed by poly(vinyl chloride)—PVC—and poly(ethylene terephthalate)—PET. In this work, the recycling of a light fraction from municipal post-consumer plastics has been studied, considering also the effect of filler type—glass fibres, calcium carbonate and wood fibres—and processing apparatus—discountinous …

1986

Ultimate tensile properties and dart impact behaviour of coextruded films of LDPE and LLDPE were compared with those of films made from blends of the same resins. The effect of composition and of both blow up ratio and axial draw ratio of the blowing process on film properties was explored. The results indicate that, at least for semicompatible systems like that considered here, films made from blends and coextruded ones have mechanical properties very close to each other. Die Festigkeitseigenschaf ten und das Verhalten beim Kugelfalltest von coextrudiertcn Filmen aus LDPE und LLDPE wurden mit den entsprechenden Eigenschaften von aus Mischungen dieser Polymere hergestellten Filmen vergliche…

Mechanical behaviour of Mater-Bi/wood flour composites: a statistical approach

2008

Interest in biocomposites (lignocellulosic filled biopolymers) started in the 90s, due to environmental advantages, related to the full biodegradability of both matrix and filler, economical issues (organic fillers usually come from sawmill or agriculture wastes) and aesthetical issues (wood filled biopolymers could be particularly pleasant if used for indoor furnishing and automotive interior). In this work, a method for a systematic study of the properties of Mater-Bi®/wood flour composites is presented. A two-level full factorial model was built. It allows investigating the effects of multiple operative variables on the observed properties, their contributions, their optimal combinations…

Reprocessing of Poly(Vinyl Chloride), Polycarbonate and Polyethyleneterephthalate

1998

Poly ethyleneterephthalate — PET- and Poly(vinyl chloride) — PVC — are two of the most frequently encountered polymers in post-consumer plastics. In particular, these polymers can be used for manufacturing the same products (bottles, for example) and therefore are often found in the same stream, even when the collection is done with separation. The recycling of PET and PVC is usually carried out by separating them and reprocessing the two homogeneous polymers. Indeed, the heterogeneous recycling of two polymers is at present almost impossible because of many problems: as their melting points are very different, at the processing temperature of PET severe degradation phenomena of PVC take pl…

Reprocessing and Properties of Homopolymer Blends of Virgin and Recycled Polymers

1998

The blends of the same virgin and recycled polymer, (homopolymer or “monopolymer” blends), show rheological and mechanical properties in most cases between those of the two components athough, in general, lower than those expected on the basis of additivity rules. In some cases, however, a minimum observed in some property versus composition curves is correlated with the change of the crystalline morphology induced by structural differences of the two components and due to different molecular weights and, in particular, the presence of oxygenated groups. In this chapter, the main properties of some homopolymer blends will be reviewed by considering, in particular, the influence of compositi…

Effect of adding new phosphazene compounds to poly(butylene terephthalate)/polyamide blends. II: Effect of different polyamides on the properties of …

2006

Poly(butylene terephthalate) (PBT) and a sample of polyamide have been melt processed in the presence of two new phosphazene compounds, namely 2,2-dichloro-4,4,6,6-bis[spyro(2',2"-dioxy-1',1"-biphenyl)]cyclotriphosphazene (2Cl-CP) and 2,2-bis(2-methoxy-4-methyleneoxy-phenoxy)-4,4,6,6-bis[spyro(2',2"-dioxy-1',1"-biphenyl)]cyclophosphazene (CP-2EPOX). The blends were prepared by using polyamide 6 (PA6) and polyamide 6,6 (PA66) in 25/75 and 75/25 w/w compositions by using a co-rotating twin-screw extruder. The materials have been completely characterized from a mechanical, rheological, and morphological point of view. The results indicate that the additives used cause an increase of the ruptur…