Search results for "Indentation"
showing 10 items of 178 documents
Photoinduced Modifications of the Structure and Microhardness of Fullerite C60
2004
The wavelength dependence, temperature limits, time and depth evolution of the photoinduced hardening of C60 crystals in air have been investigated by microindentation and dislocation mobility methods. Two photopolymerized phases, which differ in the hardness and thermal stability, are found to appear. We suggest that formation of fullerene dimers (ie. C120) in pristine fullerite and growth of C120O phase in oxygenated fullerite via [2+2] photoaddition reaction is responsible for it. It has been found from depth distribution data of the hardness that the C120O phase is located in oxygen-contaminated subsurface layer of 0.8–1 μm and appears under illumination at 290–330 K.
Accurately evaluating Young’s modulus of polymers through nanoindentations: a phenomenological correction factor to the Oliver and Pharr procedure
2006
The Oliver and Pharr [J. Mater. Res. 7, 1564 (1992)] procedure is a widely used tool to analyze nanoindentation force curves obtained on metals or ceramics. Its application to polymers is, however, difficult, as Young’s moduli are commonly overestimated mainly because of viscoelastic effects and pileup. However, polymers spanning a large range of morphologies have been used in this work to introduce a phenomenological correction factor. It depends on indenter geometry: sets of calibration indentations have to be performed on some polymers with known elastic moduli to characterize each indenter.
Indentation test as a tool for monitoring the solidification process during injection molding
2003
An inline method for monitoring the solidification process during the injection molding of semicrystalline polymers is demonstrated. The method has been applied to various poly(ethylene terephthalate) (PET) and poly(buthylene terephthalate) (PBT) samples. The technique is based on a simple device by which an additional ejector pin is pushed onto the injection-molded part with a fixed force at different times during the solidification phase while the mold remains closed. The residual deformation (the so-called indentation depth) due to the applied load is measured offline after ejection. By the performance of indentation at different times during the cooling phase, an indentation depth profi…
Nanoscale mechanical characterization of polymers by AFM nanoindentations: Critical approach to the elastic characterization
2006
AFM nanoindentations show a dependence of penetration, i.e., the relative motion between the sample and the tip (indenter), on material elastic properties when using the same load. This elationship becomes visible by using of samples being homogeneous down to the scale of nanoindentation. They were prepared from materials covering a broad range of mechanical behavior: from rubbery networks to glassy and semicrystalline polymers. The elastic modulus can be obtained applying Sneddon’s elastic contact mechanics approach. To do this, some calibrations and instrumental features have to be measured accurately. All the polymers tested show that the contact between the tip and the sample is dominat…
Magneto-Transport Results in SAM Based MTJs
2015
This chapter is dedicated to the description of the magneto-transport results obtained in LSMO/SAM/Co magnetic tunnel nanojunctions fabricated by nanoindentation lithography technique. We started by focusing on the study of LSMO/C12P/Co MTJs. This because C12P is a medium size alkyl chain: long enough to avoid short-circuits in the junction but short enough to give a device resistance in the order of few tens of MO and thus easier to measure. Next, we started to tune the molecule thickness from C10P to C18P (from 10 carbon atoms in the alkyl chain to 18). This allowed on one hand to validate our system by comparing the exponential increase of the junction resistance to the one reported in t…
On the Use of the Nanoindentation Unloading Curve to Measure the Young's Modulus of Polymers on a Nanometer Scale
2005
Summary: The nanoindentation test is a fundamental tool to assess the link between morphology and mechanical properties. The preliminary results of a more exhaustive study about the applicability to polymers of the most used procedure to determine elastic modulus by indentation are reported in this short communication. A departure of the experimental conditions from the theoretical assumptions and results that give rise to the Oliver and Pharr analysis is shown to occur under a wide range of experimental conditions, with applied loads and penetration depths covering several orders of magnitude and using different indenter geometries. Unloading curves with exponents significantly larger than…
Swift heavy ion induced modifications of luminescence and mechanical properties of polypropylene/ZnO nanocomposites
2014
Abstract The effect of irradiation with 150 MeV Kr ions at fluencies 10 11 and 10 12 ions/cm 2 on luminescence of PP/ZnO nanocomposites and PP matrix has been studied. In unirradiated composite the luminescence is comparatively weak and is contributed mainly by the excitonic luminescence of ZnO. Irradiation of nanocomposite and PP matrix leads to a strong increase of luminescence intensity in a wide spectral range of 360–600 nm. It follows from the obtained results that the enhancement of luminescence originates mainly from the broken bonds in PP matrix. Ion-induced scission of polymer bonds and fragmentation of polymer chains is deduced also from the nanoindentation tests which show a rem…
Influence of“controlled processing conditions” on the solidification of iPP, PET and PA6
2002
In this work reliable experimental data for three semicrystalline polymers (iPP, PA6, PET) crystallised under pressure and high cooling rates are supplied. These results were achieved on the basis of a model experiment where drastic controlled solidification conditions are applied. The final objective was to quantify the effect of two typical operating conditions (pressure and cooling rate) on the final properties and morphology of the obtained product. The influence of processing conditions on some macroscopically relevant properties, such as density and micro hardness is stressed, together with the influence of processing conditions on the product morphology, investigated by means of Wide…
The use of the indentation test for studying the solidification behaviour of different semicrystalline polymers during injection moulding
2005
Summary: An in-line method for monitoring the solid-ificationprocess during injection molding of semicrystallinepolymers (demonstrated previously in J. Appl. Polym. Sci.2003, 89, 3713) is based on a simple device, where anadditional ejector pin is pushed on the injection molded partatdifferenttimesduringthesolidificationphase.The‘inden-tation depth profile’, i.e., residual deformation as a functionoftime,wasobtainedandallowedtodeterminetheevolutionof the solidification front in the mold as a function of thecooling time. The present work shows the reliability andthe powerfulness of the aforementioned method for a largevariety of different semicrystalline polymers (PET, PBT,polyamide-6 PA6, isota…
Viscoelastic recovery behavior following Atomic Force Microscope nanoindentation of semi-crystalline poly(ethylene)
2007
The residual imprint left behind by the AFM nanoindentation of polymers has been seldom studied in the past. In this work, the evolution of indentations at room temperature performed on a semicrystalline poly- (ethylene) in a broad range of experimental conditions is presented. The study shows that the recovery after 24 h is substantial, although not complete. Moreover, the dynamics of the recovery process is not seen to depend on the magnitude of the applied load for the nanoindentation, but instead on the rate of the indentation used. This points out that viscoelastic processes are minimized when performing fast nanoindentations, while at low loading rates there seems to be a residual vis…