Search results for "Isolation"
showing 10 items of 582 documents
Combining congested-flow isolation and injection throttling in HPC interconnection networks
2011
Existing congestion control mechanisms in interconnects can be divided into two general approaches. One is to throttle traffic injection at the sources that contribute to congestion, and the other is to isolate the congested traffic in specially designated resources. These two approaches have different, but non-overlapping weaknesses. In this paper we present in detail a method that combines injection throttling and congested-flow isolation. Through simulation studies we first demonstrate the respective flaws of the injection throttling and of flow isolation. Thereafter we show that our combined method extracts the best of both approaches in the sense that it gives fast reaction to congesti…
Multi-Component Fault Detection in Wind Turbine Pitch Systems Using Extended Park's Vector and Deep Autoencoder Feature Learning
2018
Pitch systems are among the wind turbine components with most frequent failures. This article presents a multicomponent fault detection for induction motors and planetary gearboxes of the electric pitch drives using only the three-phase motor line currents. A deep autoencoder is used to extract features from the extended Park's vector modulus of the motor three-phase currents and a support vector machine to classify faults. The methodology is validated in a laboratory setup of a scaled pitch drive, with four commonly occurring faults, namely, the motor stator turns fault, broken rotor bars fault, planetary gearbox bearing fault and planet gear faults, under varying load and speed conditions.
Cross-correlation of whitened vibration signals for low-speed bearing diagnostics
2019
Abstract Rolling-element bearings are crucial components in all rotating machinery, and their failure will initially degrade the machine performance, and later cause complete shutdown. The period between an initial crack and complete failure is short due to crack propagation. Therefore, early fault detection is important to avoid unexpected machine shutdown and to aid in maintenance scheduling. Bearing condition monitoring has been applied for several decades to detect incipient faults at an early stage. However, low-speed conditions pose a challenge for bearing fault diagnosis due to low fault impact energy. To reliably detect bearing faults at an early stage, a new method termed Whitened …
Health Indicator for Low-Speed Axial Bearings Using Variational Autoencoders
2020
This paper proposes a method for calculating a health indicator (HI) for low-speed axial rolling element bearing (REB) health assessment by utilizing the latent representation obtained by variational inference using Variational Autoencoders (VAEs), trained on each speed reference in the dataset. Further, versatility is added by conditioning on the speed, extending the VAE to a conditional VAE (CVAE), thereby incorporating all speeds in a single model. Within the framework, the coefficients of autoregressive (AR) models are used as features. The dimensionality reduction inherent in the proposed method lowers the need of expert knowledge to design good condition indicators. Moreover, the sugg…
Fault detection for nonlinear networked systems based on quantization and dropout compensation: An interval type-2 fuzzy-model method
2016
Abstract This paper investigates the problem of filter-based fault detection for a class of nonlinear networked systems subject to parameter uncertainties in the framework of the interval type-2 (IT2) T–S fuzzy model-based approach. The Bernoulli random distribution process and logarithm quantizer are used to describe the measurement loss and signals quantization, respectively. In the framework of the IT2 T–S fuzzy model, the parameter uncertainty is handled by the membership functions with lower and upper bounds. A novel IT2 fault detection filter is designed to guarantee the residual system to be stochastically stable and satisfy the predefined H ∞ performance. It should be mentioned that…
Multi-band identification for enhancing bearing fault detection in variable speed conditions
2020
Abstract Rolling element bearings are crucial components in rotating machinery, and avoiding unexpected breakdowns using fault detection methods is an increased demand in industry today. Variable speed conditions render a challenge for vibration-based fault diagnosis due to the non-stationary impact frequency. Computed order tracking transforms the vibration signal from time domain to the shaft-angle domain, allowing order analysis with the envelope spectrum. To enhance fault detection, the bearing resonance frequency region is isolated in the raw signal prior to order tracking. Identification of this region is not trivial but may be estimated using kurtosis-based methods reported in the li…
Food tray sealing fault detection using hyperspectral imaging and PCANet
2020
Abstract Food trays are very common in shops and supermarkets. Fresh food packaged in trays must be correctly sealed to protect the internal atmosphere and avoid contamination or deterioration. Due to the speed of production, it is not possible to have human quality inspection. Thus, automatic fault detection is a must to reach high production volume. This work describes a deep neural network based on Principal Component Analysis Network (PCANet) for food tray sealing fault detection. The input data come from hyperspectral cameras, showing more characteristics than regular industrial cameras or the human eye as they capture the spectral properties for each pixel. The proposed classification…
Strategies of Identification of a Base-Isolated Hospital Building by Coupled Quasi-Static and Snap-Back Tests
2020
In this paper, the description of a series of quasi-static pushing tests and dynamic snap-back tests is proposed, involving the base-isolated emergency building of the Palermo university hospital. The base isolation system is characterized by a set of double-curved friction pendulum isolators placed on the top of the columns of the underground level, characteristics that cannot be found in the experimental studies available in the literature. The aim of the work was to investigate the static and dynamic properties of the building in question and comparing the in-situ results with the characteristics assigned during the design process and to assess the level of agreement. Static lateral push…
Seismic behavior of structures equipped with variable friction dissipative (VFD) systems
2021
Usually, to mitigate the stresses in framed structures, different strategies are used. Among them, base isolation, viscous/friction/metallic yielding dampers and tuned mass dumpers have been widely investigated. Fluid Viscous Dampers (FVD) probably result the most diffused for the simplicity in the applications. However, these type of dampers request limited interstorey drifts to avoid dangerous effects. Further, they have an elevate cost. On the contrary, friction dampers are not so expensive but request high interstorey drifts to give a significant contribute in the dissipation of energy during an earthquake. In this paper an approach for the energy dissipation by friction, modified with …
Cytoplasmic incompatibility between Old and New World populations of a tramp ant
2020
Reproductive manipulation by endosymbiotic Wolbachia can cause unequal inheritance, allowing the manipulator to spread and potentially impacting evolutionary dynamics in infected hosts. Tramp and invasive species are excellent models to study the dynamics of host-Wolbachia associations because introduced populations often diverge in their microbiomes after colonizing new habitats, resulting in infection polymorphisms between native and introduced populations. Ants are the most abundant group of insects on earth, and numerous ant species are classified as highly invasive. However, little is known about the role of Wolbachia in these ecologically dominant insects. Here, we provide the first d…