Search results for "JOINT"

A Study on the Effects of Clearance and Interference Fits in a Pin-Loaded Cross-Ply FGRP Laminate

1998

The elastic behavior of a cross-ply fiber glass-reinforced epoxy laminate loaded in tension through a pin fitted with clearance and interference is examined. A nonlinear contact analysis using the Finite Element Method and an experimental study by Speckle Interferometry are performed, showing fairly good correlation. An interesting comparison is performed between FEM results and Hertzian contact theory. Major conclusions are: (I) clearance causes high compressive stress in the bearing area, and does not influence the peak tensile stress; (2) interference has beneficial effects on the joint, as (a) it lowers the peak circumferential stress, and (b) it decreases the change of stress due to t…

Residual stresses and FCP prediction in FSW through a continuous FE model

2009

Abstract Residual stresses prediction is definitively a relevant and open issue in welding processes. In the last years, different numerical models are proposed by many researchers to predict the residual stress field in FSW butt joint. However, most of these works are based on properly tuned analytical models and neglect the effect of the mechanical action due to the presence of the tool pin. In the present paper, a continuous 3D FE model, which was previously developed by some of the authors, was used to simulate the FSW process of butt joints with a single block approach, and predict the residual stress field by considering both thermal and mechanical actions. Then, the residual stress e…

Novel silver-based nanoclay as an antimicrobial in polylactic acid food packaging coatings.

2010

This paper presents a comprehensive performance study of polylactic acid (PLA) biocomposites, obtained by solvent casting, containing a novel silver-based antimicrobial layered silicate additive for use in active food packaging applications. The silver-based nanoclay showed strong antimicrobial activity against Gram-negative Salmonella spp. Despite the fact that no exfoliation of the silver-based nanoclay in PLA was observed, as suggested by transmission electron microscopy (TEM) and wide angle X-ray scattering (WAXS) experiments, the additive dispersed nicely throughout the PLA matrix to a nanoscale, yielding nanobiocomposites. The films were highly transparent with enhanced water barrier …

Material Flow in FSW of AA7075 - T6 butt joint: numerical simulations and experimental verifications

2006

Friction stir welding (FSW) has reached a large interest in the scientific community and in the recent years also in the industrial environment, owing to the advantages of such solid state welding process with respect to the classic ones. Advanced finite element method tools are needed in order to develop an effective engineering of the processes; quantitative results can be acquired from numerical simulations once the basic information such as the material flow is certain. A 3D Lagrangian implicit coupled rigid viscoplastic model has already been developed by the authors to simulate FSW of butt joints. In the present paper the material flow in the FSW of AA7075–T6 butt joints is investigat…

Laboratory Tests for Assessing the Reliability and Durability of Innovative Cold-Glued 3D Glass Building Subcomponents

2020

The paper shows the results of analyses of the behavior of an innovative subcomponent made of two glass shells and a plastic thermal belt interfaced with a resin-based adhesive, in order to define the plastic material–adhesive combination able to guarantee compliance with the requirements related to mechanical strength, thermoacoustic insulation, dimensional stability, material compatibility, and durability. Two different types of ultraviolet (UV)-curing adhesive were used to establish the best plastic–adhesive combination. A study of the mechanical behavior and the reliability over time of the bonded assembly was conducted by performing accelerated weathering tests and tensile tests on 30 …

2017

Joint replacement surgery is associated with significant morbidity and mortality following infection with either methicillin-resistant Staphylococcus aureus (MRSA) or Staphylococcus epidermidis. These organisms have strong biofilm-forming capability in deep wounds and on prosthetic surfaces, with 103 -104 microbes resulting in clinically significant infections. To inhibit biofilm formation, we developed 3D titanium structures using selective laser melting and then coated them with a silver nanolayer using atomic layer deposition. On bare titanium scaffolds, S. epidermidis growth was slow but on silver-coated implants there were significant further reductions in both bacterial recovery (p < …

Debonding Phenomena in CFRP Strengthened Calcarenite Masonry Walls and Vaults

2009

In this paper the results of an experimental investigation on full-scale reinforced masonry elements like vaults and walls are presented. The masonry type is constituted by calcarenite ashlars and bed joint mortar and the reinforcement is constituted by Carbon Fibre Reinforced Polymer (CFRP) strips. Preliminary experimental results obtained in a previous research by the authors on the local behaviour at the interface CFRP-calcarenite are summarized. Tests with controlled displacement are carried out on out-of-plane loaded walls and cylindrical vaults loaded at a quarter of the span. Results of tests carried out before and after the application of the reinforcement made it possible to evalu…

2021

Gold-assisted mechanical exfoliation currently represents a promising method to separate ultralarge (centimeter scale) transition metal dichalcogenide (TMD) monolayers (1L) with excellent electronic and optical properties from the parent van der Waals (vdW) crystals. The strong interaction between Au and chalcogen atoms is key to achieving this nearly perfect 1L exfoliation yield. On the other hand, it may significantly affect the doping and strain of 1L TMDs in contact with Au. In this paper, we systematically investigated the morphology, strain, doping, and electrical properties of large area 1L MoS2 exfoliated on ultraflat Au films (0.16-0.21 nm roughness) and finally transferred to an i…

Experimental Characterization of FSW T-Joints of Light Alloys

2007

Welding is playing a growing role in transport industry due to relevant advantages it allows. Friction Stir Welding is considered one of the most promising joining technologies, especially when it is applied to light alloys. Focusing attention on FSW of T-joints, several parameters have to be considered, and due to thermo-mechanical features of process, T joints need a dedicated approach. A set of previously developed experiments has shown that the tilt angle plays a relevant role in the joint strength. Furthermore it should be observed that T-joints are very often utilized in aerospace industries since the produced structures are composed of joined skins and stingers. Numerous data are rep…

Numerical Procedure For Residual Stresses Prediction In Friction Stir Welding

2011

The prediction of residual stresses is a relevant and, under many points of view, still open issue for a proper welding process design. In the present paper a 3D FE model, with general validity for different joint configurations, was used to simulate the Friction Stir Welding (FSW) process of butt joints through a single block approach. The model is able to predict the residual stresses by considering thermal actions only, thanks to a new time efficient approach. A good agreement between calculated and experimentally measured data was found; the effectiveness of the presented numerical procedure was evaluated by comparing the calculation times of the proposed method with the ones of already…