Search results for "LOCI"
showing 10 items of 1277 documents
A Comprehensive Observational Study of Graupel and Hail Terminal Velocity, Mass Flux, and Kinetic Energy
2018
Abstract This study uses novel approaches to estimate the fall characteristics of hail, covering a size range from about 0.5 to 7 cm, and the drag coefficients of lump and conical graupel. Three-dimensional (3D) volume scans of 60 hailstones of sizes from 2.5 to 6.7 cm were printed in three dimensions using acrylonitrile butadiene styrene (ABS) plastic, and their terminal velocities were measured in the Mainz, Germany, vertical wind tunnel. To simulate lump graupel, 40 of the hailstones were printed with maximum dimensions of about 0.2, 0.3, and 0.5 cm, and their terminal velocities were measured. Conical graupel, whose three dimensions (maximum dimension 0.1–1 cm) were estimated from an an…
Effect of the height-to-diameter ratio on the mass transfer and mixing performance of a biotrickling filter
2017
BACKGROUND Biotrickling filters (BTFs) are among the most widely used biological technologies for air pollution control. The pollutant removal rate in BTFs relies to a large extent on its gas–liquid mass transfer performance. Therefore, knowledge of the design parameters affecting the mass transfer and mixing performance of full-scale BTFs is of paramount importance. RESULTS This work showed that the height-to-diameter (H/D) ratio is an important parameter in the design of BTFs devoted to air pollution control. The H/D ratio significantly affected the mass transfer and mixing performance of the BTF with and without additional stirring in the holding tank. It was observed that under the same…
Flow resistance law under suspended sediment laden conditions
2020
Abstract The uniform flow resistance equation, in the form due to Manning or Darcy-Weisbach, is widely applied to establish the stage-discharge relationship of a river cross-section. The application of this equation, namely the slope-area method, allows to indirectly measure the corresponding river discharge by measurements of bed slope, water level, cross-section area, wetted perimeter and an estimate of channel roughness. In this paper, a recently deduced flow resistance equation for open channel flow was tested during conditions of suspended sediment-laden flow. First, the flow resistance equation was determined by dimensional analysis and by applying the condition of incomplete self-sim…
Photo-acoustic excitation and optical detection of fundamental flexural guided wave in coated bone phantoms.
2013
Abstract Photo-acoustic (PA) imaging was combined with skeletal quantitative ultrasound (QUS) for assessment of human long bones. This approach permitted low-frequency excitation and detection of ultrasound so as to efficiently receive the thickness-sensitive fundamental flexural guided wave (FFGW) through a coating of soft tissue. The method was tested on seven axisymmetric bone phantoms, whose 1- to 5-mm wall thickness and 16-mm diameter mimicked those of the human radius. Phantoms were made of a composite material and coated with a 2.5- to 7.5-mm layer of soft material that mimicked soft tissue. Ultrasound was excited with a pulsed Nd:YAG laser at 1064-nm wavelength and received on the s…
Measuring guided waves in long bones: Modeling and experiments in free and immersed plates
2005
Guided waves, consistent with the A0 Lamb mode, have previously been observed in bone phantoms and human long bones. Reported velocity measurements relied on line fitting of the observed wave fronts. Such an approach has limited ability to assess dispersion and is affected by interference by other wave modes. For a more robust identification of modes and determination of phase velocities, signal processing techniques using the fast Fourier transform (FFT) were investigated. The limitations of FFT because of spatial resolution were addressed to improve the precision of the measured modes. An inversion scheme was developed for determining the plate thickness from the measured velocity. Experi…
Damping of rotor conical whirl by asymmetric dry friction suspension
2009
Abstract A new technique for the rotor whirl damping in rotating machinery, based on the elastic suspension of the journal boxes and the use of dry friction surfaces normal to the shaft axis between their supports and the frame, is here analysed theoretically for several cases of rotor systems characterized by mass and constraint asymmetry, where gyroscopic effects are to be expected and conical whirl motions may grow up. The critical flexural speeds can be easily cut off by an adhesive state of the supports and the whirl amplitude can be minimized as well throughout the remaining sliding range. Confining the operative angular speed of the rotor in the range of adhesive contact between the …
Application of low intensity ultrasonics to cheese manufacturing processes.
2002
Ultrasound has been used to non-destructively assess the quality of many foods such as meat, fish, vegetables and dairy products. This paper addresses the applications of low intensity ultrasonics in the cheese manufacturing processes and highlights the areas where ultrasonics could be successfully implemented in the future. The decrease of ultrasonic attenuation during the renneting process can be used to determine the optimum cut time for cheese making. The ultrasonic velocity increases during maturation for those types of cheese that become harder during this manufacturing stage, thus being an indicator of the maturity degree. Moreover, ultrasonic measurements could be linked to sensory …
Nonlinear frequency conversion in a birefringent microstructured fiber tuned by externally applied hydrostatic pressure.
2013
We studied vector frequency conversion in externally tuned microstructured fibers for applications as a novel, nonlinear fiber-optic sensor. We investigated both experimentally and numerically a possibility of shifting vector and scalar modulation instability gain bands by pressure-induced changes in the linear properties of a microstructured fiber. Our results show that polarization-dependent vector nonlinear processes sensitive to variation of fiber group velocity difference (group birefringence) exhibit a clear advantage for pressure-sensing applications compared with scalar nonlinear processes only sensitive to group velocity dispersion changes. Analytical predictions and numerical simu…
Numerical Simulation as a Tool for Design Optimization of Two-Phase Swirl Flow Atomizers
2021
This study aims to analyze the hydrodynamics in two-phase swirl flow conical atomizers. The Euler-Euler model was used for the calculations. Numerical simulations were performed to provide information about the fluid velocity distribution and the atomizer’s internal flow. The numerical calculations confirmed the experimental data. This data was found based on the consistency of the spray angles obtained by both methods. Assuming the correctness of the numerical simulations performed, they can be treated as a tool for further analysis of mass and energy exchange along with the atomizer and optimizing the atomizer’s design depending on the requirements. The influence of the swirl chamber geom…
Methyl-3-Hexenoate Combustion Chemistry: Experimental Study and Numerical Kinetic Simulation
2020
International audience; This work represents a detailed investigation of combustion and oxidation of methyl-3-hexenoate (CAS Number 2396-78-3), including experimental studies of combustion and oxidation characteristics, quantum chemistry calculations and kinetic model refinement. Following experiments have been carried out: Speciation measurements during oxidation in a jet-stirred reactor at 1 atm; chemical speciation measurements in a stoichiometric premixed flame at 1 atm using molecular-beam mass-spectrometry; ignition delay times measurements in a shock tube at 20 and 40 bar; and laminar burning velocity measurements at 1 atm using a heat-flux burner over a range of equivalence ratios. …