Search results for "Linder"

A COMPARISON BETWEEN COMBUSTION PHASE INDICATORS FOR OPTIMAL SPARK TIMING

2008

The closed-loop control of internal combustion engine spark timing may be accomplished by means of a combustion phase indicator, i.e., a parameter, derived from in-cylinder pressure analysis, whose variation is mainly referable to combustion phase shift and assumes a fixed reference value under optimal spark timing operation. The aim of the present work is a comparison between different combustion phase indicators, focusing on the performance attainable by a feedback spark timing control, which uses the indicator as pilot variable. An extensive experimental investigation has been carried out, verifying the relationship between indicators’ optimal values and the main engine running parameter…

Thin plastic foil X-ray optics with spiral geometry

2007

Winding a plastic foil ribbon into spiral cylinder or spiral cones we can design and build single or multiple reflection X-ray grazing incidence focusing optics with potential applications in Astronomy as well as experimental physics. The use of thin plastic foils from common industrial applications and of a mounting technique which does not require the construction of mandrels make these optics very cost effective. A spiral geometry focusing optic produces an annular image of a point source with the angular size of the annulus depending mainly on the pitch of the winding and the focal length. We use a ray-tracing code to evaluate the performances of cylindrical, and double conical spiral g…

Surface plasmon polaritons on metal cylinders with dielectric core

2001

International audience; Metal-cladded dielectric cylinders with submicron diameters may serve to model coated tips used in nearfield scanning optical microscopy. The signal measured may be greatly influenced by resonance effects due to eigenmodes of the probe. Especially, using a photon scanning tunneling microscope setup, gold-coated tips have been found to detect a signal proportional to the magnetic field distributions [E. Devaux et al.. Phys. Rev. B 62, 10 504 (2000)]. This effect is attributed to cylindrical surface plasmons. We present here fully retarded calculations of the dispersion and field patterns of the nonradiative plasmon modes in cylindrical geometry. We study the effect of…

Astrid Lindgrens barnböcker i ljuset av krav på bra barnlitteratur

1997

TH-C-AUD A-07: Evaluation of the Correction Factor Due to the Lack of Full Scatter Conditions in Cs-137 and Ir-192 Brachytherapy Dosimetric Studies

2008

Purpose: Use of a finite phantom to derive dose rate distributions around brachytherapysources implies a lack of backscattering material near the phantom periphery. Conventional planning algorithms and newly‐developed 3D correction algorithms are based on physics data under full scatter conditions. Presently, most published Monte Carlodosimetric studies have been obtained using either a spherical phantom (15cm in radius) or a cylinder phantom (40×40cm2). The study objective was to derive a simple relationship to correlate the radial dose function, g(r), obtained for each one of these phantoms to that obtained for an unbounded phantom. Method and Materials: Assuming bare point sources of 137…

Conformational analysis of α,β-poly(N-hydroxyethyl)-dl-aspartamide (PHEA) and α,β-polyasparthydrazide (PAHy) polymers in aqueous solution

1998

Abstract α,β-Poly(N-hydroxyethyl)- dl -aspartamide (PHEA) and α,β-polyasparthydrazide (PAHy) are synthetic polymers previously studied for biomedical applications. We report here the results of a small-angle X-ray scattering analysis carried out on these two macromolecules in aqueous solution. The data obtained indicate that the two polymers assume remarkably different conformations in aqueous solution, although the backbone is supposed to be the same for the two chains. PHEA can be represented by a random coil conformation, whereas PAHy can be described in terms of an elliptical cylinder characterized by an almost planar structural arrangement with the backbone refolded on itself in a fash…

Mechanical Behavior of Concrete Columns Confined by Laterally Pre-Tensioned FRP

2011

This paper presents the results of an experimental investigation of concrete columns confined by a wound pre-tensioned carbon filament yarn. Yarn winding equipment was developed in the Institute of Polymer Mechanics with the ability to set the desired pre-tension force and thereby producing confined concrete specimens with different initial lateral pressure. It is shown that initial lateral pressure increases the axial stress at which intense internal cracking of the concrete develops.

Wetting of mesoscopic soft cylinders: structure and layering transitions.

1998

The wetting of soft mesoscopic long-chain particles is studied. As a model system, a cylindrical brush with poly(vinyl)pyridine side chains on the water surface is characterized by isotherms and x-ray reflectivity. The forces from the two planar interfaces and the intra- and interparticle interactions are all of comparable magnitude. Two layering transitions occur, one from the monolayer to the double layer, the next to a homogeneous multilayer. The hard wall from which layering starts is the smooth polymer/air interface. Indeed, they particles in the top layer of both the double- and the multilayer have their cylinder axis parallel to the surface and are laterally compressed. In contrast, …

Pearl-necklace structures of molecular brushes with rigid backbone under poor solvent conditions: A simulation study

2010

Bottle-brush polymers, where flexible side chains containing N=20 to 50 effective monomers are grafted to a rigid backbone, are studied by molecular dynamics simulations, varying the grafting density σ and the solvent quality. Whereas for poor solvents and large enough σ the molecular brush is a cylindrical object, homogeneous in axial direction, for intermediate values of σ an axially inhomogeneous structure of "pearl-necklace" type is formed. The "pearls," however, have a strongly nonspherical ellipsoidal shape, due to the fact that several side chains cluster together in one pearl, qualitatively consistent with predictions of Sheiko et al. [Eur. Phys. J. E 13, 125 (2004)] We analyze the …

Structural properties of concave cylindrical brushes interacting with free chains

2011

We present a self-consistent field theoretical study of the microstructure of concave cylindrical brushes as a function of the cylinder radius, grafting density, grafted chain length, and the solvent quality. We show that the results for the radial monomer density profile and the distribution of the free ends are in good agreement with the corresponding molecular dynamics results. Part of the investigation is focused on the conformational behavior of a free macromolecule in a cylindrical brush. A central result is the observed non-monotonous variation of the size of a free chain in a brush-coated tube when the tube radius is systematically changed. An interpretation of this behavior which d…