Search results for "Low-density polyethylene"
showing 10 items of 99 documents
Liquid/Liquid Demixing in the System n-Hexane/Narrowly Distributed Linear Polyethylene
2004
Demixing conditions were measured visually for solutions of three narrowly distributed polyethylene samples (M ranging from 6.5 to 380 kg/mol) in n-hexane up to 500 K and 150 bar. This information yields the critical line for infinite molar mass; i.e., it specifies the pT area within which one is safe from phase separation irrespective of the molar mass of the polymer and of the composition of the mixture. The experimental findings are in good qualitative agreement with the predictions of the Sanchez−Lacombe theory applied without any adjustable parameters. The influences of molar masses are, however, underestimated, and the resulting critical compositions are too small. For a more quantita…
Rheological properties and morphology in LLDPE and PC based blends
1990
Abstract During an interlaboratory project on polymer blends (Technical Working Party-Polymer Blends-VAMAS), the rheological characteristics of some samples of blends of polycarbonate with linear low density polyethylene have been evaluated with the aid of a capillary rheometer. Some morphological observations on the extruded samples have also been performed through SEM and an attempt has been made to correlate the macroscopic and microscopic results.
Morphology and transport parameters of cold-rolled low-density polyethylene
1986
Abstract Sheets of low-density polyethylene were rolled at room temperature. Samples with two different degrees of rolling were obtained. The structural changes induced by the rolling treatments were investigated using scanning electron microscopy and by analyzing the transport properties. Results suggest that in the analyzed range of deformation, the rolling induces a domain structure as a consequence of a nonhomogeneous distribution of the deformation. At lower local deformation the initial morphology is still present, while at higher deformation clumps of folded chains oriented along the rolling directions are observable. The transport properties indicate that the rolling treatment reduc…
The role of organoclay and matrix type in photo-oxidation of polyolefin/clay nanocomposite films
2009
Abstract In this paper the photo-oxidation behaviour of polyolefin/clay nanocomposite films was studied; in particular, the effect of the amount of organo-modifier and the matrix polarity on the photo-oxidation was investigated. Two different organo-modified clays and compositions of LDPE/EVA blend films were used and the photo-oxidation was followed by mechanical and spectroscopic analyses. The organoclay and matrix type strongly influence the photo-oxidative behaviour of nanocomposite films. The films filled with CL15A show a faster loss of mechanical performance and higher carbonyl formation with respect to the films filled with the CL20A. Additionally, the LDPE based nanocomposite under…
Effective antimicrobial materials based on low-density polyethylene (LDPE) with zinc oxide (ZnO) nanoparticles
2019
[EN] Effective antimicrobial polymeric nanocomposites were prepared with low density polyethylene (LDPE) and zinc oxide nanoparticles by melt compounding. These nanoparticles (~17 nm) obtained by the sol¿gel method, were used both as-synthesized and modified organically with oleic acid (Mod-ZnO). Young¿s modulus increased ~15 and 18% for LDPE/ZnO and LDPE/Mod-ZnO, respectively, compared to neat LDPE. When these composites were irradiated with white light, they showed an increase with nanoparticle incorporation, and the antimicrobial properties against E. coli were ~96¿99%. The release of the Zn cations was related to the antimicrobial properties. These nanocomposites are attractive for use …
A simple interpretation of the effect of the polymer type on the properties of PMBs for road paving applications
2018
Abstract The paper presents the results of the rheological characterisation of polymer-modified bitumen for paving applications. In order to find a simple interpretation of the influence of polymer type on the blends produced, in this study high density and low density polyethylene (PE) with different chemical properties were used, as well as ethylene-vinyl acetate. The chemical characteristics of the base bitumen and the polymers used were determined by means of SARA analysis and Fourier Transform Infrared Spectroscopy, FTIR, respectively. The morphology of the produced blends was investigated by means of fluorescent light optic microscopy, while the mechanical properties were investigated…
Flow properties of low density/linear low density polyethylenes
1986
Rheological data have been collected both in shear and non-isothermal elongational flow on three different types of blends, made from one low density polyethylene sample and three linear low density polyethylene samples. In addition to the flow curves, data are presented on the extrudate-swell phenomenon, on the instability arising in capillary flow and on the tensile behavior in the molten state.
The rheological behavior of HDPE/LDPE blends 4. Instability phenomena in capillary flow
1984
Experimental data, relative to instability phenomena in capillary flow, have been collected for HDPE/LDPE blends already characterized from a rheological viewpoint. The data comprise morphological observations as well as the determination of critical parameters as a function of the blend composition and of the processing conditions.
Crystallization and melting of fractions of branched polyethylene
1983
Effects of the molecular weight on the crystallization behaviour of branched polyethylene become observable if isothermal crystallization is studied at temperatures near to the melting end. Crystallinities decrease with decreasing molecular weight. Thicknesses of lamellae grown during isothermal crystallization are independent of the molecular weight. They depend only on temperature. Compared to the effect of the branches polydispersity gives only a minor contribution to the broadening of the crystallization and melting range of low density polyethylene.
Orientation induced brittle – Ductile transition in a polyethylene/polyamide 6 blend
2014
Abstract Polyamide/polyolefin blends are of scientific and technological interest but, on the other hand, the different chemical nature of the two components makes them incompatible, resulting in unsatisfactory physical properties and making compatibilization necessary. In particular, although the two components are ductile, the binary blends can show brittle behaviour. It is also known that the effect of the elongational flow (and then of the induced orientation) on polymer blends is a decrease of elongation at break with increase of the degree of orientation. In this work, the effect of orientation on the mechanical properties of a low density polyethylene/polyamide 6 incompatible blend w…