Search results for "MATTER"
showing 10 items of 16762 documents
Vibronic Model for Intercommunication of Localized Spins via Itinerant Electron
2019
In this article, we propose a vibronic pseudo Jahn–Teller model for partially delocalized mixed-valence molecules aimed to describe the magnetic coupling between the localized spins mediated by the delocalized electron. The simplest partially delocalized system that retains the main studied features is assumed to consist of a one-electron mixed-valence dimer, which is connected to the two terminal magnetic ions. The model involves the following key interactions: electron transfer in the spin-delocalized subsystem of a mixed-valence molecule, which is mimicked by a dimeric unit, coupling of the itinerant electrons with the molecular vibrations, and isotropic magnetic exchange between the loc…
Impact of accumulated dust particles' charge on the photovoltaic module performance
2016
Abstract This work is focused on analysing effect of accumulated dust particles' charge on PV module performance. In the Dundee University's laboratory, dust particles have been created through epoxy powder and charged by using corona and tribo-electric charging methods by varying the charge levels of the accumulated dust particles. The PV module output has analysed for finding a relation between charge levels of the accumulated dust particles and its output voltage. Obtained experimental results have shown that charge level of accumulated dust particles on PV module's have significant impact on its output and dust particle accumulations are not associated with panel tilt angle.
Sewage sludge as cheap alternative to microalgae as feedstock of catalytic hydrothermal liquefaction processes
2019
Abstract Production of biocrude through hydrothermal liquefaction (HTL) of sewage sludge (SS) and Chlorella vulgaris was investigated. NiMo/Al2O3 (KF 851), CoMo/Al2O3 (KF 1022) and activated carbon felt, tested as catalysts at 598 K for 30 min, did not change the biocrude yield but significantly improved its quality. Quantitative sulfur removal and lower oxygen content were found in biocrude when KF 851 and KF 1022 were used with C. vulgaris. The same catalysts decreased O/C and S/C ratio of the biocrude from SS. The highest HHV (38.19 MJ/kg) and H/C ratio (1.65) and the lowest O/C (0.11) of the biocrude from SS were obtained with the cheaper activated carbon felt. A new product phase, prob…
Transition to turbulence in serpentine pipes
2017
Abstract The geometry considered in the present work (serpentine pipe) is a sequence of U-bends of alternate curvature. It is characterized by pipe diameter, d = 2a and bend diameter, D = 2c. The repeated curvature inversion forces the secondary flow pattern, typical of all flows in curved ducts, to switch between two mirror-like configurations. This causes (i) pressure drop and heat or mass transfer characteristics much different from those occurring either in a straight pipe or in a constant-curvature pipe, and (ii) an early loss of stability of the base steady-state flow. In the present work, four values of the curvature δ = a/c (0.2, 0.3, 0.4 and 0.5) were considered. For each value of …
Study about Mechanical Properties of Materials Obtained by Thermoforming
2019
Plastic materials have played a very important role in the development of our modern civilization. It can be said that plastic materials are a tribute to man’s creativity and inventiveness. Plastic materials are the key to the innovation of many products and technologies in various sectors such as electrical and electronic equipment, packaging, civil engineering, agriculture, power generation, medical and pharmaceutical industry, aerospace and not last automotive industry. An increasingly important aspect in the automotive industry, in terms of fuel consumption is the lower weight of the components, while maintaining a very high stiffness. The difficulties of the design process of thermofor…
Definition of the thermographic regions of interest in cycling by using a factor analysis
2016
Abstract Research in exercise physiology using infrared thermography has increased in the last years. However, the definition of the Regions of Interest (ROIs) varies strongly between studies. Therefore, the aim of this study was to use a factor analysis approach to define highly correlated groups of thermographic ROIs during a cycling test. Factor analyses were performed based on the moment of measurement and on the variation of skin temperatures as a result of the cycling exercise. 19 male participants cycled during 45 min at 50% of their individual peak power output with a cadence of 90 rpm. Infrared thermography was used to measure skin temperatures in sixteen ROIs of the trunk and lowe…
A new strategy to maximize organic matter valorization in municipalities: combination of urban wastewater with kitchen food waste and its treatment w…
2017
[EN] The aim of this study was to evaluate the feasibility of treating the kitchen food waste (FW) jointly with urban wastewater (WW) in a wastewater treatment plant (WWTP) by anaerobic membrane technology (AnMBR). The experience was carried out in six different periods in an AnMBR pilot-plant for a total of 536 days, varying the SRT, HRT and the food waste penetration factor (PF) of food waste disposers. The results showed increased methane production of up to 190% at 70 days SRT, 24 hours HRT and 80% PF, compared with WW treatment only. FW COD and biodegradability were higher than in WW, so that the incorporation of FW into the treatment increases the organic load and the methane producti…
The role of extracellular polymeric substances on aerobic granulation with stepwise increase of salinity
2018
Abstract A granular sequencing batch reactor (GSBR) worked for 164 days to study the effect of salinity on aerobic granulation. The feeding had an organic loading rate (OLR) of 1.6 kg COD⋅m −3 ⋅d −1 and a gradual increase of salinity (from 0.30 to 38 g NaCl − ⋅L −1 ) to promote a biological salt-adaptation. First aggregates (average diameter ≈ 0.4 mm) appeared after 14 days. Extracellular polymeric substances (EPSs) analyses revealed that proteins were mainly higher than polysaccharides, and microorganisms metabolized EPSs as additional carbon source, mostly in feast phase, to face the energy demand for salinity adaptation. No significant worsening of organic matter removal was observed. Th…
Comparison between Deep-Drawing and Incremental Forming Processes from an Environmental Point of View
2019
Deep-drawing is an industrial forming process which allows the user to process large batches of sheet metals parts. One of the major drawbacks of this process is the complexity and the high cost of dies. In comparison incremental forming is a flexible process, allowing the user to obtain sheet metal parts without the need of using a die. The present paper aims to present a comparative study of the two forming processes by presenting the main advantages and drawbacks of each one. The comparative study, aimed on the industrial implementation of the incremental forming process requires a comparison of the two processes regarding the environmental impact. Thus, the results of the study will jus…
Vibration Control of a High-Speed Precision Servo Numerically Controlled Punching Press: Multidomain Simulation and Experiments
2017
A three-degree-of-freedom mathematical vibration model of a high-speed punching press was developed in order to explore the vibration modes of the punching press. A multidomain model of the punching press was established to predict the kinematic state during different conditions, as well as the effects of load fluctuation on the motor speed. Experimental measurements of the acceleration of the punching press were carried out. The results comparison reveals that the multidomain model is consistent with the vibration model and the experimental measurements. Modal analysis and structure modification of the punching press were conducted. The foundation at the base of the punching press was impr…