Search results for "MECHANICAL PROPERTIES"
showing 10 items of 199 documents
Green Composites Based on Hedysarum coronarium with Outstanding FDM Printability and Mechanical Performance
2022
The addition of natural scraps to biodegradable polymers has gained particular interest in recent years, allowing reducing environmental pollution related to traditional plastic. In this work, new composites were fabricated by adding 10% or 20% of Hedysarum coronarium (HC) flour to Poly (lactic acid) (PLA). The two formulations were first produced by twin screw extrusion and the obtained filaments were then employed for the fabrication of composites, either for compression molding (CM) or by fused deposition modeling (FDM), and characterized from a morphological and mechanical point of view. Through FDM it was possible to achieve dense structures with good wettability of the filler that, on…
Conifer needles as thermoplastic composite fillers: structure and properties
2016
This study describes the properties of thermoplastic polymer composites based on polyethylene (of low and high density) and ethylene-propylene copolymers using various types of conifer needles (pine, spruce, fir, and cedar) as fillers. For the needles, thermogravimetric analysis (TGA) and TGA/Fourier transform infrared spectroscopy (TGA/FTIR) were performed to investigate their structures and thermal resistance, as required for the composite processing methods. Moreover, structural differences were studied for the analyzed fillers and composite materials (FTIR). The results were compared with the values obtained for composites with conifer wood flour. Composites with conifer needles (pine) …
High performance PA6/CNTs nanohybrid fibers prepared in the melt
2012
Commercial and home-made carbon nanotubes (CNTs) were plasma treated under oxygen atmosphere and then added to polyamide 6 (PA6) in order to prepare fibres by melt spinning. For comparison, pristine nanofillers were used too. The effect of functionalization and of filler characteristics on the morphological, rheological, mechanical and electrical properties of the fibres was studied by TEM and SEM, rheological measurements, tensile and electrical conductivity tests. The results demonstrated that the functionalization led to a better mechanical performance and the morphological analysis confirmed that the adhesion, the dispersion and the alignment of the nanotubes within the polymer matrix w…
Characterization of a fiber-reinforced new fully aromatic liquid crystalline polymer
1998
A new rigid liquid crystalline polymer that demonstrates good mechanical and thermomechanical properties and acceptable processing temperature has been recently synthesized and characterized. The melting temperature and some thermomechanical properties do not seem, however, suitable for use in some applications at high temperature or in the presence of aggressive fluids. The use of appropriate inorganic fillers can overcome these shortcomings. In this work the new LCP, polymerized in a bench-scale apparatus, and the same sample filled with carbon fibers are characterized. The properties of the carbon fiber filled LCP are compared with those of another filled wholly aromatic commercial LCP,…
Processability and Properties of Re-Graded, Photo-Oxidized Post-Consumer Greenhouse Films
2005
The recycling of post‐consumer plastics leads, in general, to secondary materials having properties worse than those of the reclaimed material and certainly worse than those of the same virgin polymer. This is because of the degradation undergone by the objects during their use and because of the thermo‐mechanical degradation undergone during the reprocessing operations. The change of the molecular architecture is responsible for this worsening of properties. The use of stabilizing systems can slow the degradation during the melt processing but cannot give any improvement of the final properties of the material. In order to enhance the properties of the recycled plastics, some rebuilding of…
Effect of stress and temperature on the thermomechanical degradation of a PE-LD/OMMT nanocomposites
2014
Thermomechanical degradation of nanocomposites is a topical issue that has not been fully investigated as demonstrated by the low number of papers available in the literature regarding this spe- cific aspect. In particular, with regards to low density polyethylene/clay nanocomposites, the degrada- tion behavior is very complex since it involves the degradation paths of both the polymer matrix and the organomodified nanoclay. In the present work, the effects of mechanical stress and temperature on the thermomechanical behavior of PE-LD/organomodified clay nanocomposites and the degradation paths were investigated by rheological, FT-IR and mechanical methods. The results have shown that the t…
Mechanical Characterization of Polysaccharide/polyaminoacid Hydrogels as Potential Scaffolds for Tissue Regeneration
2011
The mechanical properties of hydrogel scaffolds based on hyaluronic acid (HA) that were chemically crosslinked with α,β-poly(N-2-hydroxyethyl)(2-aminoethylcarbamate)-D,L-aspartamide (PHEA-EDA) were investigated. Variation of these properties as a function of three different PHEA-EDA amounts used to crosslink HA has been related to the reaction efficiency evaluated using a colorimetric assay. Moreover, the amount of unreacted amino groups that was still present in the hydrogels was related to the attachment behavior of human dermal fibroblasts to the hydrogel surface. The mechanical data and biological results suggest the suitability of the investigated hydrogels as scaffolds for the regener…
Numerical model for composite material with polymer matrix reinforced by carbon nanotubes
2008
Due to the high stiffness and strength, as well as their ability to act as conductors, carbon nanotubes are under intense investigation as fillers in polymeric materials. The nature of the carbon nanotube/polymer bonding and the curvature of the carbon nanotubes within the polymer have arisen as particular factors in the efficacy of the carbon nanotubes to actually provide any enhanced stiffness or strength to the nanocomposite. Here the effects of carbon nanotube curvature and interface interaction with the matrix on the nanocomposite stiffness are investigated using nanomechanical analysis. In particular, the effects of poor bonding and thus poor shear lag load transfer to the carbon nano…
Effect of small amounts of poly(lactic acid) on the recycling of poly(ethylene terephthalate) bottles
2011
Abstract Poly(ethylene terephthalate) (PET) is one of the most used commodity polymers, especially for food and beverage applications, and its recycling is of great importance because of the possible use in the textile and construction industries. On the other hand, the interest in biodegradable polymers has led, in recent years, to the use of materials such as poly(lactic acid) (PLA) also in the food and beverage industry. The presence of small amounts of PLA in the PET waste can significantly affect the post-consumer recycling process. In this work, the effect of the presence of small amounts of PLA on the recycling of PET bottles is investigated by rheological, mechanical, morphological …
Photooxidation and Stabilization of Photooxidized Polyethylene and of its Monopolymer Blends
2003
The increasing use of products from recycled polymers, or from blends with recycled polymers exposed to the outdoors, implies the need for good weathering resistance. This is particularly important when the recycled material comes, in turn, from products exposed during their lifetime to the sun. In this case the presence of C=O groups in the macromolecular chains strongly increases the photooxidative degradation kinetics of these secondary materials. In this work the change of the photooxidative degradation of blends of virgin and photooxidized polyethylene was evaluated as a function of the C=O content present in the material. As expected, the presence of the C=O groups strongly increases …