Search results for "MINERALOGY"
showing 10 items of 1516 documents
Characterization by solid-state NMR and selective dissolution techniques of anhydrous and hydrated CEM V cement pastes.
2010
International audience; The long term behaviour of cement based materials is strongly dependent on the paste microstructure and also on the internal chemistry. A CEM V blended cement containing pulverised fly ash (PFA) and blastfurnace slag (BFS) has been studied in order to understand hydration processes which influence the paste microstructure. Solid-state NMR spectroscopy with complementary X-ray diffraction analysis and selective dissolution techniques have been used for the characterization of the various phases (C3S, C2S, C3A and C4AF) of the clinker and additives and then for estimation of the degree of hydration of these same phases. Their quantification after simulation of experime…
Preparation of synthetic sandstones with variable cementation for studying the physical properties of granular rocks
1997
In this article, we report a new set of procedures to fabricate synthetic analogues of granular rocks. These procedures permit accurate control of the most important structural parameters (i.e., grain size, porosity, cement content). We were thus able to prepare two varieties of synthetic sandstones in which only the cement content significantly varied. Our procedures were also particularly successful in producing materials that were very similar to natural rocks. To demonstrate this similarity, we compared the microstructure, the mechanical properties (i.e., strength, elastic moduli) and the mechanical behaviour (i.e., brittle or ductile) of the synthetic materials to those of various natu…
Effect of blastfurnace slag addition to Portland cement for cationic exchange resins encapsulation
2013
In the nuclear industry, cement-based materials are extensively used to encapsulate spent ion exchange resins (IERs) before their final disposal in a repository. It is well known that the cement has to be carefully selected to prevent any deleterious expansion of the solidified waste form, but the reasons for this possible expansion are not clearly established. This work aims at filling the gap. The swelling pressure of IERs is first investigated as a function of ions exchange and ionic strength. It is shown that pressures of a few tenths of MPa can be produced by decreases in the ionic strength of the bulk solution, or by ion exchanges (2Na + instead of Ca 2+ , Na + instead of K + ). Then,…
Studies on mechanism and physico-chemical parameters at the origin of the cement setting. I. The fundamental processes involved during the cement set…
1995
Abstract The mechanical evolution and the structure of the cement paste have been analysed in relation with the chemical evolution of the system. The setting process can be described as following two fundamental steps: the coagulation of cement grains during the first minutes following the mixing, and the rigidification of the coagulated structure which arises simultaneously with the acceleration of the hydrates formation During the coagulation step, the structure formed is proved to be mechanically reversible. The rigidification of the coagulated structure is provided by the hydrates formation in the contact zone. The increase of the paste cohesion at this stage is proportional to the quan…
Importance of the liquid to solid weight ratio in the powdered solid-liquid reactions Example drawn from cement constituent hydration
1997
Abstract It seems justified to wonder if the chemical processes which have been evidenced from diluted stirred suspensions are or are not in accordance with those involved in a stagnant paste. The present paper is aimed at clarifying this question which is in connection with the problem of the so called ‘dormant period’ or ‘induction period’ at the beginning of the hydration of Portland cement.
Electrokinetic Properties which Control the Coagulation of Silicate Cement Suspensions during Early Age Hydration
1998
The coagulation of cement particles during early age hydration has been previously identified as the first step of the setting and hardening of cement pastes. By hydrating Ca3SiO5and a silicate-rich clinker under controlled conditions, a correlation between the coagulation of the suspensions and the electrokinetic properties of particles is established. The zeta potential, and hence the surface charge, of particles in suspension depends on the calcium content of the medium. At low concentrations of Ca2+, the zeta potential of Ca3SiO5particles, calcium silicate hydrate (C–S–H), and clinker is negative (<−30 mV) and the suspensions are well dispersed. A strong coagulation occurs at intermedia…
Correlation between surface forces and surface reactivity in the setting of plaster by atomic force microscopy
2000
Abstract The setting of mineral binders (cement, plaster, etc.) arises as a direct consequence of surface reactivity by a process of dissociation and rehydration. This transformation induces a complete change of surface forces, of which the nature remains still unknown. The general process of the setting has been studied by means of plaster (CaSO 4 ·0.5H 2 O) crystals, chosen for an experimental convenience. The surface alteration (growth, dissolution, atomic resolution) of the plaster crystal with respect to the introduction of the calcium sulfate solution has been followed by using atomic force microscopy (AFM. Alternatively, this apparatus has been adapted by gluing a plaster microcrysta…
Hydration of alite containing aluminium
2011
Abstract The most important phase in Portland cement is tricalcium silicate, which leads during its hydration to the nucleation and growth of calcium silicate hydrate [referred to as C–S–H, (CaO)x–SiO2–(H2O)y]. The development of this hydrate around the cement grains is responsible for the setting and hardening of cement pastes. The general term for designating the tricalcium silicate in cements is alite. This name relates to all polymorphs containing various foreign ions inserted in their structure. These ions may influence the intrinsic reactivity, and once released during the dissolution, they may interact also with C–S–H. One of the most likely species to be inserted in the alite struct…
On the physico-chemical evolution of low-pH and CEM I cement pastes interacting with Callovo-Oxfordian pore water under its in situ CO2 partial press…
2014
International audience; Abstract Within the framework of geological repositories for radioactive waste, structural concretes must be adapted to the underground chemical conditions. CEM I cement-based materials are characterised by high pH that may produce an alkaline plume in the near-field of the repository. In order to avoid this problem, low-pH cements have been designed. This study compares the physico-chemical behaviour of a low-pH material with a CEM I cement paste, both being subjected to leaching by an aqueous solution. An original experimental setup was designed to reproduce the underground conditions using a specific CO2 regulation device. Under these conditions, the low-pH materi…
Studies on mechanism and physico-chemical parameters at the origin of the cement setting II. Physico-chemical parameters determining the coagulation …
1996
The physico-chemical parameters determining the coagulation of cements grains previously identified as the first fundamental process of cement setting have been investigated in diluted suspensions using an adapted granulometric method. The analysis of the influence of the ionic concentration in solution on the coagulation reveals that calcium concentration is the parameter which determines the particle interactions. There exists a minimum critical concentration of calcium ions in solution which is required to occur the coagulation of cement particles and a dispersive effect appears for very high concentrations. The results are discussed in relation with DLVO theory and specific interactions.