Search results for "Measurement"

Electromechanical coupling in anodic niobium oxide: Electric field-induced strain, internal stress, and dielectric response

2012

Seemingly, contradictory results have been reported so far for electrostriction in anodic oxides. Furthermore, no definitive agreement could be obtained with theory. In this paper, in situ techniques are combined to elucidate electrostriction in anodic niobium oxide. The dependence of strain, internal stress, and dielectric constant on the electric field is measured by, respectively, spectroscopic ellipsometry, curvature, and impedance measurements. The through-thickness strain is tensile and proportional to the square of the electric field. The in-plane internal stress is compressive and proportional to the square of the electric field at low field values. The internal stress is predicted …

Design and Validation of the Brief Self Online Scale (SO-8) in Early Adolescence: An Exploratory Study

2020

For the Z-Generation, the Internet has become a very important experimentation laboratory for the discovery and validation of their identity. Despite the importance of the process of building the self in the adolescent, there are hardly any validated instruments that measure the self online. The aim of this research was to design and validate the Brief Self Online Scale (SO-8). A total of 843 students (384 boys, 45.6%), with an age range of 10 to 14 years participated. Confirmatory factor analysis (CFA) confirmed the hypothesized model of two correlated factors (Online Self-Perception and Online Idealized Projection), previously obtained through exploratory factor analysis (EFA). The relia…

An Aircraft Pilot Workload Sensing System

2021

The workload evaluation is of great importance for human error avoidance training, particularly in the use of complex systems that requires different and concurrent activities. The excessive workload harms human performance even with adverse outcomes. In the aviation field, certain flight maneuvers, such as take-off and landing, are characterized by great attention and workload demand to the pilot. Thus, a system capable of measuring pilots’ workload levels during flight could be beneficial to increase pilots’ performance. This work aims to study the initial feasibility of a device called Cockpit Pilot Warning System that monitors the pilot workload level during flight. With this aim, an ex…

New technique for measuring water depth in rill channels

2019

Abstract Water erosion is one of the most important soil degradation processes and rill erosion contribution to total soil loss is usually dominant as compared to interrill erosion. Rill erosion modelling requires that rill flow has to be adequately modelled. Flow depths in rills are typically of the order of millimeters to several centimeters and bed topography, characterized by steep slope values, significantly affects flow hydraulics. In this paper, a new technique for measuring the water depth inside a rill channel is proposed and the effects on flow resistance estimate are examined. This technique couples an accurate ground survey of the rill channel, obtained by close-range photogramm…

Closure to “Theoretical End‐Depth‐Discharge Relationship for Free Overfall” by Vito Ferro

2000

Using Beerkan experiments to estimate hydraulic conductivity of a crusted loamy soil in a Mediterranean vineyard

2019

Abstract In bare soils of semi-arid areas, surface crusting is a rather common phenomenon due to the impact of raindrops. Water infiltration measurements under ponding conditions are becoming largely applied techniques for an approximate characterization of crusted soils. In this study, the impact of crusting on soil hydraulic conductivity was assessed in a Mediterranean vineyard (western Sicily, Italy) under conventional tillage. The BEST (Beerkan Estimation of Soil Transfer parameters) algorithm was applied to the infiltration data to obtain the hydraulic conductivity of crusted and uncrusted soils. Soil hydraulic conductivity was found to vary during the year and also spatially (i.e., ro…

Multivariate Methods Based Soft Measurement for Wine Quality Evaluation

2014

Published version of an article in the journal: Abstract and Applied Analysis. Also available from the publisher at: http://dx.doi.org/10.1155/2014/740754 Open Access Soft measurement is a new, developing, and promising industry technology and has been widely used in the industry nowadays. This technology plays a significant role especially in the case where some key variables are difficult to be measured by traditional measurement methods. In this paper, the quality of the wine is evaluated given the wine physicochemical indexes according to multivariate methods based soft measurement. The multivariate methods used in this paper include ordinary least squares regression (OLSR), principal c…

A COMPARISON BETWEEN COMBUSTION PHASE INDICATORS FOR OPTIMAL SPARK TIMING

2008

The closed-loop control of internal combustion engine spark timing may be accomplished by means of a combustion phase indicator, i.e., a parameter, derived from in-cylinder pressure analysis, whose variation is mainly referable to combustion phase shift and assumes a fixed reference value under optimal spark timing operation. The aim of the present work is a comparison between different combustion phase indicators, focusing on the performance attainable by a feedback spark timing control, which uses the indicator as pilot variable. An extensive experimental investigation has been carried out, verifying the relationship between indicators’ optimal values and the main engine running parameter…

Electrical conductivity as a state indicator for the start-up period of anaerobic fixed-bed reactors.

2016

The aim of this work was to analyse the applicability of electrical conductivity sensors for on-line monitoring the start-up period of an anaerobic fixed-bed reactor. The evolution of bicarbonate concentration and methane production rate was analysed. Strong linear relationships between electrical conductivity and both bicarbonate concentration and methane production rate were observed. On-line estimations of the studied parameters were carried out in a new start-up period by applying simple linear regression models, which resulted in a good concordance between both observed and predicted values. Electrical conductivity sensors were therefore identified as an interesting method for monitori…

The need for recovery scale

2013

Abstract Introduction Need for Recovery scale is one of the main scales used to assess work-induced fatigue and quality of workers’ recovery time. In fact, need for recovery is considered relevant as a precursor of prolonged fatigue or psychological distress, an indicator of work stress, and a mediating or moderating characteristic in the etiology of work-related health problems, sick leave and work disability. Objective The purpose of the present study is to translate the Need for Recovery scale into Italian, and to adapt it to Italian culture; until now there has been no comparable valid instrument made for the Italian language that measures the need for recovery of employees. The stabili…