Search results for "Medium"
showing 10 items of 3746 documents
Fast pyrolysis of hot-water-extracted and delignified silver birch (Betula pendula) sawdust by Py-GC/MS
2017
The thermochemical behavior of birch (Betula pendula) sawdust both untreated and after various chemical treatments (hot-water extraction, delignification, and hot-water extraction followed by delignification) was investigated by pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS). In each case, major GC-amenable condensable products were classified into several compound groups, and the formation of these monomer-related fragments from feedstock samples with varying mass portions of the structural constituents (cellulose, hemicelluloses, and lignin) were determined at 500 °C and 700 °C at hold times of 5 s and 20 s. The formation of pyrolysis products was shown to be characteristically…
SiC Based Latching Current Limiter for High Voltage Space Power Distribution Systems
2018
This study presents a novel Latching Current Limiter topology, based on a N-channel Silicon Carbide (SiC) MOSFET as the main switching element. The design has been carried out using only discrete components, without digital controllers. This design has been validated by simulation and with a prototype. Tests have been performed at 1000V, modifying the limitation times, current-limiting values and eventually checking the proper operation of the system.
Regarding the influence of the particle size of crumb rubber from waste rubber on the physical and mechanical characteristics of reclaimed rubber
2017
Thus, at present, a large amount of rubber waste cannot be higher harnessed due to recovery technologies used. Also, the requirements for new products of rubber worldwide are greater than the production capacity and the availability of raw materials. To offset this balance is necessary to improve technologies for recycling waste rubber so to can get regenerated rubber with the best mechanical physical characteristics. The main technology for obtaining the regenerated rubber is based on the rubber waste shredding and making the powder, so that it can be carried out de-vulcanization in autoclave. All the time it was monitored as the de-vulcanization process to be as economical and less pollut…
Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach
2020
In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…
Geometrical deviation of end-of-life parts as a consequence of reshaping by single point incremental forming
2021
AbstractPutting in place circular economy strategies is an urgent challenge to face. In this scenario, manufacturing processes play a relevant role as efficient material reuse enabler. Scientists have to make an effort either to find new process or to rethink old process to reprocess end-of-life (EoL) component to recover both material and functions. In this paper, single point incremental forming (SPIF) process is used for reshaping sheet metal EoL components. The entire process chain was replicated including both deep drawing process (to imitate the end-of-life component) as well as SPIF operations (to obtain the reshaped components). The geometrical deviation as a consequence of SPIF ope…
Re-forming end-of-life components through single point incremental forming
2020
Abstract Applying Circular Economy strategies is mandatory to face material demand while minimizing the environmental impact. Manufacturing processes are to be thought as means to enable material/component reuse strategies. This paper presents the suitability of Single Point Incremental Forming (SPIF) to re-form End-of-life sheet metal components. Deep drawing followed by SPIF process on aluminium alloys were carried out to simulate reforming processes chain. The resulting thinning and strain distributions were experimentally analysed for different configurations. The research proves that the local action and enhanced formability nature of SPIF allow non-homogeneously thinned and reduced fo…
Effect of the mutual position between weld seam and reinforcement on the residual stress distribution in Friction Stir Welding of AA6082 skin and str…
2016
Abstract In the paper, a numerical and experimental study was carried out to highlight the effect of the distance d between the weld seam and the reinforcement on the residual stress distribution in Friction Stir Welded AA6082-T6 structures. An L-shaped profile was welded to a sheet metal with varying tool rotation and distance d from the weld seam. The Cut Compliance method was used to determine the resulting longitudinal residual stress. A dedicated FE model for FSW was set up, validated and utilized to predict the longitudinal residual stress in the assembled part. The analysis allowed the identification of a few design guidelines in order to reduce the detrimental effects of the residua…
A Pareto optimal design approach for simultaneous control of thinning and springback in stamping processes
2009
One of the most relevant research issues in automotive field is focused on the reduction of stamped parts weight also increasing their strength. In this way, a strong research effort is developed on high strength steels which are widely utilized and they require a proper springback control. Springback reduction in sheet metal forming is a typical goal to be pursued which is conflicting with thinning reduction for instance. Thus, such problems can be considered as multi-objective ones characterized by conflicting objectives. What is more, nowadays, a great interest would be focused on the availability of a cluster of possible optimal solutions instead of a single one, particularly in an indu…
Influence of friction stir processing conditions on the manufacturing of Al-Mg-Zn-Cu alloy/boron carbide surface composite
2018
Abstract Surface metal matrix composites were synthesized via friction stir processing (FSP) on the surface of aluminium alloy 7075 (AA 7075) sheets by incorporating B4C particles (B4CP). The influence of tool rotational speeds, powder particle sizes, and change in tool travel direction between FSP passes on particle distribution and resulting properties were studied in detail. Change in tool travel direction, decreased tool rotation speed and fine B4C particles enhanced B4CP distribution and wear properties thereof. Wear resistance of composites were doubled on account of the B4CP distribution and resultant several strengthening mechanisms.
Impact of accounting process characteristics on accounting outsourcing - Comparison of users and non-users of cloud-based accounting information syst…
2019
Article In Press The article of record as published may be found at https://doi.org/10.1016/j.accinf.2019.06.002 Prior literature informs us that a company's decision to outsource a business process depends on process characteristics such as how frequently the process is performed or how specific the assets required by the process are. In this article, we compare the effects of accounting process characteristics on outsourcing decisions across users of traditional and cloud-based accounting information systems (AIS). By focusing on outsourcing of accounting processes among small and medium sized enterprises, we investigate the effect of five business process characteristics (frequency, huma…