Search results for "Metallurgy"
showing 10 items of 1419 documents
Synthesis and processing of nanocrystalline tungsten carbide: Towards cemented carbides with optimal mechanical properties
2011
Abstract Nanocrystalline tungsten carbide has been obtained by reduction/carburization at low temperature from precursors obtained by freeze-drying of aqueous solutions. Nanocrystalline WC powders with a adequate content of carbon were mixed with submicrometric Cobalt powder (12 wt.%), obtained by same synthesis method, and sintered in vacuum furnace. The cemented carbides fabricated from experimental powders were compared with both commercial ultrafine and nanocrystalline WC-12Co mixtures consolidated by the same route. The synthesised powders were characterized by X-ray powder diffraction, elemental analysis and scanning and high resolution transmission electron microscopy. On the other h…
Electrochemistry of iron oxide pigments (earths) from pictorial microsamples attached to graphite–polyester composite electrodes
2001
The electrochemical response of different iron pigments attached to graphite–polyester composite electrodes is described. Characteristic differential pulse voltammetric profiles were obtained for green earth, iron oxide red, Mars black, ochre yellow, Sienna raw, umber raw and Van Dyke brown. Proton-assisted reductive dissolution processes occur at the three-phase boundary of the substrate electrode–attached solid–electrolyte solution system. Microsamples extracted from polychromed sculptures, canvas paintings, wall paintings, altarpieces and panel paintings from Spain, Ethiopia and Italy from the 12th to the 20th centuries were electrochemically identified in agreement with polarized light …
Damage monitoring on carbonate stones: Field exposure tests contributing to pollution impact evaluation in two Italian sites
2017
During the last decades, many studies have been carried out on environmental monitoring in specific sites aiming at their protection and conservation; however, researches focused on the direct implications, in terms of quantitative evaluation of stone deterioration, of these monitoring actions are still scarce. This experimental work aims at monitoring the degradation processes affecting historical buildings constituted by carbonate stones. Specifically, specimens of Carrara marble and two limestones largely used in the Sicilian Baroque architecture, namely Noto and Comiso stones, were exposed outdoor in two Italian sites (Catania and Palermo), which are characterized by different environme…
Environmental impact of early Basque mining and smelting recorded in a high ash minerogenic peat deposit.
2004
International audience; More than four metres of core, covering almost 5000 years of deposition, were collected in a high ash minerogenic peat deposit located in the High Aldudes valley (Basque country), an area well known for its mineral abundance, exploited from Roman Times at least.Although minerogenic peatlands are not generally considered as the best archives to reconstruct past atmospheric metal deposition history, lead isotopic geochemistry demonstrates the integrity of the Pb record at least within the three upper meters; that is to say over the last four millennia.Zn, Cd and Cumay have been widely redistributed either by biological cycling, advective groundwater movements, or diffu…
Inverse modeling of past lead atmospheric deposition in South Greenland
2015
The aim of this study is to model atmospheric lead fluxes in two different paleoenvironmental records located in southern Greenland. Fifty five sediment samples collected from the Lake Igaliku sedimentary sequence were analyzed for lead and aluminum concentrations, and lead isotopic compositions. The second archive consists in a previously published dataset, obtained from a minerogenic peat deposit, located at Tasiusaq, 16 km northwest from Lake Igaliku. A flux model fitted to both dataset produces similar results, allowing past anthropogenic atmospheric deposition to be reconstructed. This original method can be easily adapted for other studies where natural inputs dominate over discrete a…
Coupling geochemical, mineralogical and microbiological approaches to assess the health of contaminated soil around the Almalyk mining and smelter co…
2013
This study describes the impact of airborne pollution resulting from mining and smelting activities on the soils of the Almalyk mining and industrial area (NE Uzbekistan). Samples were collected along a transect downwind of the industrial area. Enriched contents of some metals were found in the upper soil layers near the metallurgical complex (Zn≤3010 mg kg(-1), Pb≤630 mg kg(-1), Cd≤30 mg kg(-1)) which suggests that these metals were derived from local stack emissions. The morphology and internal microstructure of metal-bearing spherical particles found in the heavy mineral fraction suggest that these particles were probably a result of inefficient flue gas cleaning technique of the smelter…
Influence of the Residual Stresses Induced by Shot-Peening on the Oxidation of Zr Plates
2014
The present study evaluates the influence of the residual stress on the oxidation rate of Zr at 650°C. It is shown that the oxidation rate can be substantially decreased by shot-peening. A systematic instigation of the various factors (such as the residual stress, the surface pollution and the chemical composition of the oxidation atmosphere) is realized to separate their influence on the oxidation. The influence of an annealing made after the shot-peening is also considered. One show that the pollution of the surface during the shot-peening process is not responsible for the oxidation rate decrease.
Heptanuclear hydroxo-bridged copper cluster of the dicubane-like type: structural and magnetic characterisations of [Cu7(OH)6Cl2(pn)6(H2O)2](C(CN)3)4…
2002
A new polynuclear copper(II) complex [Cu7(OH)6Cl2- (pn)6(H2O)2](C(CN)3)4Cl2 with hydroxo-bridging ligands has been prepared; the centrosymmetric cluster cation can be described as two Cu4O3Cl distorted cubane units sharing one copper cation. Clemente Juan, Juan Modesto, Juan.M.Clemente@uv.es ; Gomez Garcia, Carlos Jose, Carlos.Gomez@uv.es ; Coronado Miralles, Eugenio, Eugenio.Coronado@uv.es
FEM Simulation of Laminated Lightweight Materials Processed through Single Point Incremental Forming
2015
The aim of present paper is to realize the FEM simulation of laminated lightweight material processed through single point incremental forming. Thus a laminated material, aluminum - polypropylene - aluminum (Al-PP-Al), as sheet 1.2 mm thickness was used. For these material the hardening curve was determinate. These values were used to describe elastic-plastic behavior of the material during single point incremental forming process simulation. Single point incremental forming process simulation aimed to assess the distribution of values and maximum and minimum strains, the material thickness of the specimen and the technological force for the two strategies for obtaining the truncated cone s…
Structure, morphology and crystallization of a random ethylene-propylene copolymer
2003
The structure, morphology, and crystallization behavior of a random ethylene–propylene copolymer, containing 2 wt % ethylene sequences, are analyzed and compared with those of a plain polypropylene sample by means of optical and scanning microscopy, wide-angle X-ray scattering, and calorimetry. For the copolymer, different polymorphs (α, γ and smectic modifications) and morphologies can be obtained through changes in the crystallization and annealing conditions. The analysis of the structural results suggests that the γ phase of isotactic polypropylene can be generated for high molecular mass samples with drastic decreases in the undercooling. The spherulite growth rate (G) data, in conjunc…