Search results for "Modelling"
showing 10 items of 1353 documents
The Augmented Reality as an Instrument for the Representation/Visualization of Architecture
2019
This paper deals with issues related to the representation/visualization of architecture and its narration through the augmented reality tools. Specifically, the possible scenarios and the different strategies to address the problems related to the application of AR platforms in the field of cultural heritage are presented. Some case studies will be analyzed and the use of augmented reality applied to museums and archaeological sites including the Museum of the Cité de l'architecture et du patrimoine in Paris, the Regional Archaeological Museum A. Salinas in Palermo and the archaeological site of Selinunte. Thanks to these exemplary cases, the potential and critical aspects of the latest AR…
Exploiting 3D Modelling and Life Cycle Assessment to Improve the Sustainability of Pavement Management
2020
Today road agencies worldwide face difficult decisions for construction, maintenance and rehabilitation of their road infrastructure as they try to balance limited budgets. This is further complicated rising environmental concerns over equipment and techniques used for these practices. This has led agencies to consider alternative approaches for smarter and sustainable pavement asset management systems. This paper considers the use of a low-cost 3D image modelling distress identification and classification proposal for data acquisition and analysis. To establish its environmental friendliness, a case study in Palermo, Italy, is considered wherein a Life Cycle Assessment (LCA) exercise is do…
Calibration of a knock prediction model for the combustion of gasoline-LPG mixtures in spark ignition engines
2015
Gaseous fuels, such as liquefied petroleum gas (LPG) and natural gas (NG), thanks to their good mixing capabilities, allow complete and cleaner combustion than gasoline in spark ignition (SI) engines, resulting in lower pollutant emissions and particulate matter. In a previous work the authors showed that the simultaneous combustion of gasoline and LPG improves an SI engine efficiency with respect to pure gasoline operation with any significant power loss. The addition of LPG to the gasoline-air mixture produces an increase in knock resistance that allows running the engine at full load with overall stoichiometric mixture and better spark advance. In order to predict both performance and ef…
The dynamics over the next few years of the Spanish mobile telecommunications market share: a mathematical modelling approach
2013
Taking into account available data from 2002 to 2009 about the market share percentages of the Spanish mobile telecommunications service providers, a dynamic diffusion model to study the evolution of the clients’ change between the different companies during the period 2010–2016 is proposed. The constructed model provides a tool for forecasting short-term trends about the customers’ preferences with respect to mobile network operators taking into account both, autonomous decisions due to direct marketing and advertising strategies, and also decisions adopted through interaction via social influence. The model can provide insights to companies for designing strategies in order to gain market…
Large-eddy simulations of turbulent flow with heat transfer in simple and complex geometries using Harwell-FLOW3D
1996
Abstract Large-eddy simulation (LES) results are presented and discussed for the turbulent flow with heat transfer in different geometrical configurations, including a plane channel, a channel bearing transverse square ribs on one of the walls, and a crossed-corrugated air heater. They were obtained using the computational fluid dynamics (CFD) code Harwell-FLOW3D (Release 2), finite-volume grids having up to 423 nodes, and the Smagorinsky subgrid model with several variants regarding near-wall damping and wall boundary conditions. The first problem (plane turbulent Poiseuille flow with heat transfer) was mainly used as a benchmark to investigate the influence of numerical methods (pressure-…
CHA on CDK2: a way to identify the best pharmacophore model for the virtual screening of new inhibitors
2018
Cyclin-dependent kinase-2 (CDK2) is a member of serine/threonine protein kinases family. It plays an important role in the regulation events of the eukaryotic cell division cycle, especially during the G1 to S phase transition. Experimental evidences indicate that excessive expression of CDK2 should cause abnormal cell cycle regulation. Therefore, CDK2 has been considered a potential therapeutic target for cancer therapy. In this work, we used a modelling approach that incorporates flexibility based on extensive MD simulations of protein−ligand complexes into structure-based pharmacophore modeling and virtual screening to identify new CDK2 inhibitors. One-hundred and forty-nine CDK2-inhibit…
Effect of the junction angle on turbulent flow at a hydraulic confluence
2018
Despite the existing knowledge concerning the hydrodynamic processes at river junctions, there is still a lack of information regarding the particular case of low width and discharge ratios, which are the typical conditions of mountain river confluences. Aiming at filling this gap, laboratory and numerical experiments were conducted, comparing the results with literature findings. Ten different confluences from 45 ∘ to 90 ∘ were simulated to study the effects of the junction angle on the flow structure, using a numerical code that solves the 3D Reynolds Averaged Navier-Stokes (RANS) equations with the k- ϵ turbulence closure model. The results showed that the higher the junction angle, the …
Mechanical And Thermophysical Properties Of Polymers And Chemical Structure: From Computer Simulations To Experimental Data
1988
Chemical structure is related to properties on the basis of results of computer modelling of mechanical behavior. An equation for the shift factor aT,c dependent on temperature T and concentration c is provided, connection to the chain relaxation capability noted, and potential application range of the approach discussed. Constituents of free volume are defined, and effects of individual constituents on mechanical properties.
Prediction of the morphology of polymer-clay nanocomposites
2015
Abstract Polymer nanocomposites have continually attracted increasing interest over the last decade, due to significant improvements they can offer compared to neat polymer matrices. However, the final morphology of a nanocomposite, determined by several variables, can significantly influence the macroscopic properties of the final product. Therefore, it is important to study the interactions between processing, morphology, structure and rheological properties, and the suitability of existing models in order to predict the system's behaviour with change of the main processing variables. In this work, the applicability of a predictive theory based on the Wu model was formulated and proposed …
Wastewater modification processes in a stabilization reservoir: a new mathematical model
2018
The paper presents a mathematical model for the simulation of the ecology of a wastewater stabilization reservoir (WSR). WSRs are hypertrophic aquatic systems devoted to water storage in warm countries where shortage conditions are often encountered. Several factors that affect the stabilization reservoir’s effluent quality were taken into account: hydraulics and hydrology, solar radiation, reaeration, algae, zooplankton, organic matter, pathogens, and sediment-water interactions. The model quantifies the specific influence of each factor on effluent quality, and evaluating the correlation between the different factors. State variables included in the model were: algae, dissolved oxygen, or…