Search results for "Modulus"
showing 10 items of 491 documents
In situ measurement of elastic properties of PdH , PdD , and PdT
2003
Abstract The Young’s modulus E of palladium hydride PdH x , deuteride PdD x and tritide PdT x were measured for studying the effect of both hydrogen stoichiometry x and isotope nature. A special technique based on optical detection of flexural modes of a palladium cylindrical microcantilever was adapted to in situ measurements to guarantee the sample homogeneity during the hydriding process. A 10% decrease in E was found between pure polycrystalline palladium and hydride phases. The non linear dependence observed with the H content was discussed in terms of lattice expansion, phonons and electronic properties. Sensitivity of the technique enables to distinguish an isotope effect on E .
Mechanical Characterization of Polymers on a Nanometer Scale through Nanoindentation. A Study on Pile-up and Viscoelasticity
2007
The analysis of nanoindentation force curves collected on polymers through the common Oliver and Pharr procedure does not lead to a correct evaluation of Young’s modulus. In particular, the estimated elastic modulus is several times larger than the correct one, thus compromising the possibility of a nanomechanical characterization of polymers. Pile-up or viscoelasticity is usually blamed for this failure, and a deep analysis of their influences is attempted in this work. Piling-up can be minimized by indenting on a true nanometer scale, i.e., at penetration depth smaller than 200 nm. On the other side, it is common knowledge that fast indentations minimize the effect of viscoelasticity. How…
Elasticity and yield strength of pentagonal silver nanowires: In situ bending tests
2014
This paper reports in situ mechanical characterization of silver nanowires (Ag NWs) inside a scanning electron microscope using a cantilevered beam bending technique. Measurements consisted in controlled bending of a cantilevered NW by the tip of an atomic force microscope glued to the force sensor. Relatively high degree of elasticity followed by either plastic deformation or fracture was observed in bending experiments. Experimental data were numerically fitted into the model based on the elastic beam theory and values of Young modulus and yield strength were extracted. Measurements were performed on twenty Ag NWs with diameters from 76 nm to 211 nm. Average Young modulus and yield streng…
Physico-chemical and mechanical characterization of in-situ forming xyloglucan gels incorporating a growth factor to promote cartilage reconstruction
2016
Abstract The development of growth factors is very promising in the field of tissue regeneration but specifically designed formulations have to be developed in order to enable such new biological entities (NBEs). In particular, the range of therapeutic concentrations is usually very low compared to other active proteins and the confinement in the target site can be of crucial importance. In-situ forming scaffolds are very promising solutions for minimally invasive intervention in cartilage reconstruction and targeting of NBEs. In this work injectable, in-situ forming gels of a temperature responsive partially degalactosylated xyloglucan (Deg-XG) incorporating the growth factor FGF-18 are fo…
Using ultrasound transmission velocity to analyse the mechanical properties of teeth after in vitro, in situ, and in vivo irradiation.
2000
Ultrasound transmission velocity (UTV) in isotropic material as a measure for the modulus of elasticity was correlated to mechanical properties. Changes in micromechanical properties of radiated teeth and influence of the oral cavity were to be evaluated nondestructively. UTV was measured in extracted teeth after 36 Gy and 62 Gy of in situ (enorally, with no contact to the oral cavity) and in vitro irradiation. Relative to controls, teeth subjected to 62 Gy in vivo showed higher UTV values for dentine and enamel. Sound teeth irradiated with 60 Gy in situ also showed higher UTV values for enamel, whereas dentine values were not significantly different from those of control. The mechanical pr…
Pressure Effect Investigations on the Spin Crossover Systems{Fe[H 2 B(pz) 2 ] 2 (bipy)} and {Fe[H 2 B(pz) 2 ] 2 (phen)}
2006
Pressure effect studies on the spin crossover behaviour of the mononuclear compounds {Fe[H2B(pz)2]2(bipy)}(1) and {Fe[H2B(pz)2]2(phen)}(2) have been performed in the range of 105 Pa–1.02 GPa at variable temperatures (100–310 K). Continuous spin transitions and displacement of its characteristic temperature has been observed for 1 with increasing pressure. Meanwhile the response of 2 under applied pressures is quite unexpected, and can only be understood in terms of a crystallographic phase transition or change in the bulk modulus of the compound. (© Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2006)
Comparative Study of the Compressibility of M3V2O8 (M = Cd, Zn, Mg, Ni) Orthovanadates
2022
We report herein a theoretical study of the high-pressure compressibility of Cd3V2O8, Zn3V2O8, Mg3V2O8, and Ni3V2O8. For Cd3V2O8, we also present a study of its structural stability. Computer simulations were performed by means of first-principles methods using the CRYSTAL program. In Cd3V2O8, we found a previously unreported polymorph which is thermodynamically more stable than the already known polymorph. We also determined the compressibility of all compounds and evaluated the different contributions of polyhedral units to compressibility. We found that the studied vanadates have an anisotropic response to compression and that the change in volume is basically determined by the compressi…
Compressibility and Structural Stability of Nanocrystalline TiO2 Anatase Synthesized from Freeze-Dried Precursors
2014
The high-pressure structural behavior of 30 nm nanoparticles of anatase TiO2 was studied under hydrostatic and quasi-hydrostatic conditions up to 25 GPa. We found that the structural sequence is not sensitive to the use of different pressure transmitting media. Anatase-type nanoparticles exhibit a phase transition beyond 12 GPa toward a baddeleyite-type structure. Under decompression this phase transition is irreversible, and a metastable columbite-type structure is recovered at ambient conditions. The bulk modulus of anatase-type nanoparticles was determined confirming that nanoparticles of TiO2 are more compressible than bulk TiO2. Similar conclusions were obtained after the determination…
Locking Reconstruction Double Plating of Distal Humeral Fractures: How Many Screws in the Distal Ulnar Column Segment in A3 Fracture Provide Superior…
2009
Objectives: Two 90-degree configurations of locking reconstruction plates with different numbers of screws in the distal ulnar column segment of distal extra-articular humeral fractures with metaphyseal comminution (A3) were biomechanically investigated. Methods: Eight pairs of fresh-frozen human humeri were used. For paired comparison, the humeri were divided into 2 randomized groups. In both groups, double-plate osteosyntheses with locking reconstruction plates were performed in 90-degree configurations. In group 1, the posteriorly placed radial column plate exceeded the capitellum and the ulnar column plate extended into the ulnar sulcus. The ulnar plate was molded around the medial epic…
An experimental and constitutive investigation on the chemo-mechanical behaviour of a clay
2013
Engineering issues for which the understanding of the chemo-mechanical behaviour of soils is relevant include wellbore stability problems, the salinification of groundwater, and nuclear waste storage. However, despite the vast number of situations in which couplings between chemistry and mechanics occur, the available constitutive models rely on limited experimental evidence. This paper presents the results of an experimental programme on the chemo-mechanical behaviour of a non-swelling illite. The osmotic suction is controlled through the ion concentration of sodium chloride in the pore water. Stress paths include mechanical loading at a constant osmotic suction, and an increasing osmotic …