Search results for "NGS"
showing 10 items of 6306 documents
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…
A new approach to simulate coating thickness in cold spray
2020
Abstract In the process of cold spray on complex components, the coating thickness is an important indicator to monitor and control. Current methods such as destructive tests or direct mechanical measurements can only be performed after spraying. Besides, these methods lead to production shutdown and additional costs . This article presents a novel approach predicting coating thickness for components with complex curved surfaces, especially in the case of shadow effects. Firstly, a three-dimensional geometric model of the coating profile based on Gaussian distribution was developed. In addition, the relative deposition efficiency (RDE) resulting from the different robot kinematic parameters…
Optimisation of refractory coatings realised with cored wire addition using a high-power diode laser
2005
Laser; Cladding; Refractory alloys; Factorial experiments; International audience; The objective or our research was to obtain refractory alloys using the high-power diode laser (HPDL) coating technique. After optimisation using factorial experiments, two different cladding regimes were clearly distinguished. It was also shown that a very narrow transition zone exists between the two regimes, and, inside this zone, clad layers having a satisfactory compromise between the response functions (surface aspect and cavity presence) were obtained. The main objective of our study, namely, the control of the operating parameters (geometrical and kinematical) to realise adequate coatings, without cav…
Parallel distributed compensation for voltage controlled active magnetic bearing system using integral fuzzy model
2018
Parallel Distributed Compensation (PDC) for current-controlled Active Magnetic Bearing System (AMBS) has been quite effective in recent years. However, this method does not take into account the dynamics associated with the electromagnet. This limits the method to smaller scale applications where the electromagnet dynamics can be neglected. Voltage-controlled AMBS is used to overcome this limitation but this comes with serious challenges such as complex mathematical modelling and higher order system control. In this work, a PDC with integral part is proposed for position and input tracking control of voltage-controlled AMBS. PDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy model. …
Vibration control strategy for large-scale structures with incomplete multi-actuator system and neighbouring state information
2016
The synthesis of optimal controllers for vibrational protection of large-scale structures with multiple actuation devices and partial state information is a challenging problem. In this study, the authors present a design strategy that allows computing this kind of controllers by using standard linear matrix inequality optimisation tools. To illustrate the main elements of the new approach, a five-story structure equipped with two interstory actuation devices and subjected to a seismic disturbance is considered. For this control setup, three different controllers are designed: an ideal state-feedback H 8 controller with full access to the complete state information and two static output-fee…
Friction Model for Tool/Work Material Contact Applied to Surface Integrity Prediction in Orthogonal Cutting Simulation
2017
Abstract Tribological behavior at both tool/chip and tool/work material interfaces should be highly considered while simulating the machining process. In fact, it is no longer accurate to suppose one independent constant friction coefficient at the tool/chip interface, since in reality it depends on the applied contact conditions, including the sliding velocity and pressure. The contact conditions at both above mentioned interfaces may affect the thermal and mechanical phenomena and consequently the surface integrity predictions. In this article, the influence of contact conditions (sliding velocity) on the tribological behavior of uncoated tungsten carbide tool against OFHC copper work mat…
Towards Shipping 4.0. A preliminary gap analysis
2020
Abstract The paradigm of Industry 4.0 involves a substantial innovation to the value creation approach thought the supply chain and the application of digital enabling technologies like the Internet of Things (IoT), Big Data Analytics (BDA) and cloud computing. The fourth industrial revolution is thus expected to have a disruptive impact on maritime transport and shipping sectors, where smart ships and autonomous vessels well be part of a new and fully interconnected maritime ecosystem. Specific hardware components, such as sensors, actuators, or processors will be embedded in the ship’s key systems in order to provide valuable information to increase the efficiency, sustainability and safe…
A flexible robotic cell for in-process inspection of multi-pass welds
2020
Welds are currently only inspected after all the passes are complete and after allowing sufficient time for any hydrogen cracking to develop, typically over several days. Any defects introduced between passes are therefore unreported until fully buried, greatly complicating rework and also delaying early corrections to the weld process parameters. In-process inspection can provide early intervention but involves many challenges, including operation at high temperatures with significant gradients affecting acoustic velocities and, hence, beam directions. Reflections from the incomplete parts of the weld would also be flagged as lack-of-fusion defects, requiring the region of interest (ROI) t…
Hypervisor Memory Introspection and Hypervisor Based Malware Honeypot
2020
Memory acquisition is a tool used in advanced forensics and malware analysis. Various methods of memory acquisition exist. Such solutions are ranging from tools based on dedicated hardware to software-only solutions. We proposed a hypervisor based memory acquisition tool. [22]. Our method supports ASLR and Modern operating systems which is an innovation compared to past methods [27, 36]. We extend the hypervisor assisted memory acquisition by adding mass storage device honeypots for the malware to cross and propose hiding the hypervisor using bluepill technology.
HyperWall: A Hypervisor for Detection and Prevention of Malicious Communication
2020
Malicious programs vary widely in their functionality, from key-logging to disk encryption. However, most malicious programs communicate with their operators, thus revealing themselves to various security tools. The security tools incorporated within an operating system are vulnerable to attacks due to the large attack surface of the operating system kernel and modules. We present a kernel module that demonstrates how kernel-mode access can be used to bypass any security mechanism that is implemented in kernel-mode. External security tools, like firewalls, lack important information about the origin of the intercepted packets, thus their filtering policy is usually insufficient to prevent c…