Search results for "Note"
showing 10 items of 10709 documents
Core-shell Zn-doped TiO2-ZnO nanofibers fabricated via a combination of electrospinning and metal-organic chemical vapour deposition
2010
Zn-doped TiO2 nanofibers shelled with ZnO hierarchical nanoarchitectures have been fabricated combining electrospinning of TiO2 (anatase) nanofibers and metal-organic chemical vapor deposition (MOCVD) of ZnO. The proposed hybrid approach has proven suitable for tailoring both the morphology of the ZnO external shell as well as the crystal structure of the Zn-doped TiO2 core. It has been found that the Zn dopant is incorporated in calcined electrospun nanofibers without any evidence of ZnO aggregates. Effects of different Zn doping levels of Zn-doped TiO2 fibers have been scrutinized and morphological, structural, physico-chemical and optical properties evaluated before and after the hierarc…
Study of the structural changes induced by air oxidation in Ti–Si–N hard coatings.
2008
International audience; 3-μm thick Ti–Si–N coatings were deposited on polished X38CrMoV5 substrates by sputtering a composite Ti–Si target in Ar–N2 reactive mixture. Oxidation tests were performed in air at 700 °C during 2 h. Whatever the silicon content in the range 0–4 at.%, no silicon containing compound was detected by XRD before air oxidation and only the TiN phase was evidenced. The mean grain size estimated from the full width at half maximum of the TiN (111) diffraction peak was close to 10 nm. As commonly reported for Ti–Si–N films, the hardness showed a maximum at 51 GPa versus the Si content. After oxidation of the TiN film, XRD and micro-Raman analyses revealed the occurrence of…
Effect of Reynolds number and lithium cation insertion on titanium anodization
2016
This work studies the influence of using hydrodynamic conditions (Reynolds number, Re = 0 to Re = 600) during Ti anodization and Li+ intercalation on anatase TiO2 nanotubes. The synthesized photocatalysts were characterized by using Field Emission Scanning Electron Microscope (FE-SEM), Raman Confocal Laser Microscopy, Electrochemical Impedance Spectroscopy (EIS), Mott-Schottky analysis (M-S), photoelectrochemical hydrogen production and resistance to photocorrosion tests. The obtained results showed that the conductivity of the NTs increases with Li+ intercalation and Re. The latter is due to the fact that the hydrodynamic conditions eliminate part of the initiation layer formed over the tu…
Removal of Surface Oxygen Vacancies Increases Conductance Through TiO(2) Thin Films for Perovskite Solar Cells
2019
[Image: see text] We report that UV–ozone treatment of TiO(2) anatase thin films is an efficient method to increase the conductance through the film by more than 2 orders of magnitude. The increase in conductance is quantified via conductive scanning force microscopy on freshly annealed and UV–ozone-treated TiO(2) anatase thin films on fluorine-doped tin oxide substrates. The increased conductance of TiO(2) anatase thin films results in a 2% increase of the average power conversion efficiency (PCE) of methylammonium lead iodide-based perovskite solar cells. PCE values up to 19.5% for mesoporous solar cells are realized. The additional UV–ozone treatment results in a reduced number of oxygen…
Effect of Reynolds number on TiO2 nanosponges doped with Li+ cations
2018
[EN] Anatase TiO2 nanosponges have been synthesized by anodization of Ti, and Li+ cations have been inserted in these nanostructures. The influence of hydrodynamic conditions (Reynolds number, Re = 0 to Re = 600) during anodization has been studied. Li-Doped TiO2 nanosponges were characterized by field emission scanning electron microscopy (FE-SEM), Raman confocal microscopy, electrochemical impedance spectroscopy (EIS) and Mott¿Schottky analysis (M¿S). The photoelectrochemical performance and resistance to photocorrosion were also measured. Li¿TiO2 nanosponges proved to be better photocatalysts for water splitting than Li¿TiO2 nanotubes. Moreover, the photoelectrochemical behavior of the L…
TiO2 nanostructures prepared by ferrocene/cobalt catalyst agents
2008
We present the growth and characterization of TiO2 nanocrystals. Nanostructured growth is obtained in a low-pressure CVD system by using an organometallic precursor Ti(OC3H7)4 as both the Ti and O source catalyzed by both ferrocene (an organometallic precursor) and cobalt metallic clusters prepared by the microwave-assisted polyol method. Two kinds of TiO2 structures were obtained in the cobalt clusters: a) pine-tree like (with short-leaf structure) and b) long-leaf structures as large as a few micrometers in size and both under 10 nm in thickness. Long-leaf TiO2 structures were grown at cobalt grain boundaries. For the growth conditions utilized, the TiO2 structures are composed of both an…
Symmetry and models of single-walled TiO2 nanotubes with rectangular morphology
2011
Abstract The formalism of line symmetry groups for one-periodic (1D) nanostructures with rotohelical symmetry has been applied for symmetry analysis of single-walled titania nanotubes (SW TiO2 NTs) formed by rolling up the stoichiometric two-periodic (2D) slabs of anatase structure. Either six- or twelve-layer (101) slabs have been cut from TiO2 crystal in a stable anatase phase. After structural optimization, the latter keeps the centered rectangular symmetry of initial slab slightly compressed along a direction coincided with large sides of elemental rectangles. We have considered two sets of SW TiO2 NTs with optimized six- and twelve-layer structures, which possess chiralities (−n, n) an…
Partial photoelectrocatalytic oxidation of 3-pyridinemethanol by Pt, Au and Pd loaded TiO2 nanotubes on Ti plate
2021
Abstract The photoelectrocatalytic (PEC) oxidation of 3-pyridinemethanol to 3-pyridinemethanal and vitamin B3 was investigated by using Pt, Au and Pd loaded (as single or bimetallic) nanotube structured TiO2 on Ti plate in water under UVA irradiation. Nanotube structured TiO2 on Ti plate samples were prepared as anode by anodic oxidation method in ethylene glycol solution in different times, and then they were calcined at 500 °C to be obtained in crystalline form. The anodes were loaded with noble metals by electrochemical reduction method and characterized by XRD, XPS, SEM, and photocurrent techniques. The TiO2 on the plates was in the anatase phase. The loaded metals were in metallic form…
Ab initiomodeling of sulphur doped TiO2nanotubular photocatalyst for water-splitting hydrogen generation
2012
In order to construct an efficient visible-light-driven TiO2 photocatalyst for water splitting applications, one has to perform improvements of its electronic structure. In this theoretical study we consider single-walled anatase TiO2 nanotubes having following morphologies: (101) 3-layered wall with chirality indexes (n,0) and (n,n), (101) 6-layered wall with (n,0) and (0,n), (001) 6-layered wall with (n,0) and (0,n), and (001) 9-layered wall with (n,0) and (0,n). The latter configuration occurs to be the most energetically stable, due to possessing negative strain energy. In our study the most stable 9-layered anatase (001) (0,n) nanotube has been doped with sulphur. According to obtained…
Photoluminescence: A very sensitive tool to detect the presence of anatase in rutile phase electrospun TiO 2 nanofibers
2015
Abstract This paper reports on the synthesis and the characterization of titanium dioxide (TiO2) nanofibers prepared by electrospinning. The samples were annealed at various temperatures in air for 4 h. The as-spun and annealed TiO2/PVP composite nanofibers were characterized by scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy analysis (EDX), X-ray diffraction (XRD), Raman spectroscopy and photoluminescence (PL). The results show that the heat treatment has an effect on the crystallization process. Even if the XRD data shows a complete anatase-to-rutile transition in the TiO2 nanofibers at 900 °C, photoluminescence reveals a small portion of anatase in rutile sample.…