Search results for "Nuclear engineering"
showing 10 items of 533 documents
On the optimization of the first wall of the DEMO water-cooled lithium lead outboard breeding blanket equatorial module
2016
Abstract Within the framework of EUROfusion R&D activities a research campaign has been carried out at the University of Palermo in order to investigate the thermo-mechanical performances of the DEMO water-cooled lithium lead (WCLL) breeding blanket first wall (FW). The research campaign has been mainly focused on the optimization of the FW geometric configuration in order to maximize the heat flux it may safely withstand fulfilling all the thermal, hydraulic and mechanical requirements foreseen by safety codes. Attention has been focused on the FW flat concept endowed with square cooling channels and the potential influence of its four main geometrical parameters on its thermo-mechanical p…
Analysis of the thermomechanical behavior of the IFMIF bayonet target assembly under design loading scenarios
2015
In the framework of the IFMIF Engineering Validation and Engineering Design Activities (IFMIF/EVEDA) phase, ENEA is responsible for the design of the European concept of the IFMIF lithium target system which foresees the possibility to periodically replace only the most irradiated and thus critical component (i.e., the backplate) while continuing to operate the rest of the target for a longer period (the so-called bayonet backplate concept). In this work, the results of the steady state thermomechanical analysis of the IFMIF bayonet target assembly under two different design loading scenarios (a "hot" scenario and a "cold" scenario) are briefly reported highlighting the relevant indications…
Study of the thermo-mechanical performances of the IFMIF-EVEDA Lithium Test Loop target assembly
2012
Abstract Within the framework of the IFMIF R&D program and in close cooperation with ENEA-Brasimone, at the Department of Energy of the University of Palermo a research campaign has been launched to investigate the thermo-mechanical behavior of the target assembly under both steady state and start-up transient conditions. A theoretical approach based on the finite element method (FEM) has been followed and a well-known commercial code has been adopted. A realistic 3D FEM model of the target assembly has been set-up and optimized by running a mesh independency analysis. A proper set of loads and boundary conditions, mainly concerned with radiation heat transfer between the target assembly ex…
Optimization of the breeder zone cooling tubes of the DEMO Water-Cooled Lithium Lead breeding blanket
2016
Abstract The determination of an optimal configuration for the breeder zone (BZ) cooling tubes is one of the most important issues in the DEMO Water-Cooled Lithium Lead (WCLL) breeding blanket R&D activities, since BZ cooling tubes spatial distribution should ensure an efficient heat power removal from the breeder, avoiding hotspots occurrence in the thermal field. Within the framework of R&D activities supported by the HORIZON 2020 EUROfusion Consortium action on the DEMO WCLL breeding blanket design, a campaign of parametric analyses has been launched at the Department of Energy, Information Engineering and Mathematical Models of the University of Palermo (DEIM), in close cooperation with…
Numerical assessment of the thermomechanical behaviour of the DEMO Water-Cooled Lithium Lead inboard blanket equatorial module
2018
Abstract Within the framework of EUROfusion R&D activity, a research campaign has been carried out at the University of Palermo, in close cooperation with ENEA labs, in order to assess the thermo-mechanical performances of the DEMO Water-Cooled Lithium Lead (WCLL) inboard blanket equatorial module, whether properly integrated within its whole inboard segment. In particular, a detailed 3D model of this segment, including all the other modules, the back-supporting structure and the attachment system, has been considered in order to realistically simulate the boundary conditions affecting the equatorial module behaviour. The study has been focused on the investigation of the module thermo-mech…
Neutronic and photonic analysis of the water-cooled Pb17Li test blanket module for ITER-FEAT
2002
Abstract Within the European Fusion Technology Program, the Water-Cooled Lithium Lead (WCLL) DEMO breeding blanket line was selected in 1995 as one of the two EU lines to be developed in the next decade, in particular with the aim of manufacturing a Test Blanket Module (TBM) to be implemented in ITER. This specific goal has been maintained also in ITER-FEAT program even if the general design parameters of the TBMs have reported some changes. This paper is focused on the investigation of the WCLL-TBM nuclear response in ITER-FEAT through detailed 3D-Monte Carlo neutronic and photonic analyses. A 3D heterogeneous model of the most recent design of the WCLL-TBM has been set-up simulating reali…
On the nuclear response of the water-cooled Pb-17Li test blanket module for ITER-FEAT
2003
Abstract Within the European Fusion Technology Programme, the Water-Cooled Lithium Lead (WCLL) DEMO breeding blanket line was selected in 1995 as one of the two EU lines to be developed in the next decades, in particular with the aim of manufacturing a Test Blanket Module (TBM) to be tested in ITER-FEAT. The present paper is focused on the study of the WCLL-TBM nuclear response in ITER-FEAT, being specifically oriented to the investigation of the local effects due to the typical C-shaped tubes of the breeder zone, since they could play a pivotal role in the module-relevant thermo–mechanical design. A 3D heterogeneous model of the WCLL-TBM, realistically simulating its new lay out and taking…
Thermomechanical analysis supporting the preliminary engineering design of DONES target assembly
2018
Abstract The design of the Demo Oriented NEutron Source (DONES) is the main objective of the Work Package Early Neutron Source (WPENS) of EUROfusion Power Plant Physics and Technology (PPPT) programme. DONES is an IFMIF-based neutron source with the goal of testing and qualifying candidate materials to be used in DEMO and future fusion power plants. In the framework of these activities, a research campaign has been carried out at the University of Palermo, in close cooperation with ENEA labs, in order to assess the thermomechanical performances of the DONES target system, endowed with an integrated Target Assembly (TA) when it undergoes the thermomechanical loads typical of its nominal oper…
Direct sunlight facility for testing and research in HCPV
2014
A facility for testing different components for HCPV application has been developed in the framework of "Fotovoltaico ad Alta Efficienza" (FAE) project funded by the Sicilian Regional Authority (PO FESR Sicilia 2007/2013 4.1.1.1). The testing facility is equipped with an heliostat providing a wide solar beam inside the lab, an optical bench for mounting and aligning the HCPV components, electronic equipments to characterize the I-V curves of multijunction cells operated up to 2000 suns, a system to circulate a fluid in the heat sink at controlled temperature and flow-rate, a data logging system with sensors to measure temperatures in several locations and fluid pressures at the inlet and ou…
Transient DC-Arc Voltage Model in the Hybrid Switch of the DTT Fast Discharge Unit
2021
The focus of this work is the transient modelling of the DC-arc voltage on a Hybrid Switch (a mechanical switch in parallel with a static switch) of a key protection component called Fast Discharge Unit (FDU) in the Divertor Tokamak Test (DTT). The DTT facility is an experimental tokamak in advanced design and realization phase, which will be built in the ENEA Research Centre in Frascati (Italy). The FDU allows the safe discharge of the Toroidal Field (TF) superconducting magnets when a quench is detected or a failure occurs in the power supply or in the cryogenic system. In this work, the arc conductance of the mechanical By-Pass Switch (BPS) of the Hybrid Switch is modelled using the well…