Search results for "Numerical"
showing 10 items of 2002 documents
Numerical model for the characterization of biocomposites reinforced by sisal fibres
2018
Abstract Although several works have been recently published in literature about biocomposites, i.e. on innovative and ecofriendly polymer matrix composites reinforced by natural fibers, there are not studies on the influence of the waviness that various natural fiber present after their extraction. In order to give a contribution to the knowledge of the effects of the fiber waviness on the main mechanical properties of biocomposites, as the longitudinal Young modulus, in the present study a systematic numerical analysis has been carried out by using parametric models properly developed, that let the user to consider the effects of the key influence parameters as the fiber concentrations an…
Experimental and Numerical Analysis on FSWed Magnesium Alloy Thin Sheets Obtained Using “Pin” and “Pinless” Tool
2012
The present investigation aims at studying the effect of different tool geometries and process parameters on FSW of thin sheets in AZ31 magnesium alloy. In particular two properly designed tools, with shoulder diameters equal to 8 and 19 mm, were used; each of them was manufactured both in pin and pinless configurations. The effect of the different tool configurations and sizes, and welding parameters on mechanical properties of FSWed joints were analyzed in detail. The results were compared with those obtained on the base material. It was shown that FSWed joints are characterized by strength and ductility values lower than those of base material. Furthermore, the pin tool configuration, wi…
An Improved Thermal Lamination Model for Analysis of Heat Transfer in Composite Structures
2002
A new thermal lamination model and its associated finite element model are presented for analysis of heat transfer in laminated composite structures. The form of the present model closely resembles that of recent zig-zag sublaminate structural laminate theories. The through-thickness distribution of temperature is assumed to vary linearly within each ply, and continuity of transverse flux at ply interfaces is enforced analytically. Thus, the number of computational degrees-offreedom (DOFs) is made independent of the number of plies in the sublaminate. In its present form, the model contains only two computational DOFs in each sublaminate–the temperature at the top and bottom surface of the…
A model for predicting the mixed-mode fatigue crack growth in a bonded joint
2013
Bonded joints are highly sensitive to the presence of defects and to the degradation phenomena, and this aspect represents the primary obstacle to their use in different structural engineering applications. Delamination in a bonded joint represents, in fact, one of the primary, most common and insidious causes of damage. In this paper, a numerical–experimental study on the crack propagation along the adhesive layer of a bonded joint specimen is carried out. Experimental study is focused on the evaluation of the damage modalities of a bonded joint when the specimens are subject to fatigue load. Experimental tests are compared with the results of several numerical analysis performed in ANSYS …
Electroelastic Analysis of Piezoelectric Composite Laminates by Boundary Integral Equations
2004
A boundary integral representation for the electroelastic state in piezoelectric composite laminates subjected to axial extension, bending, torsion, shear/bending, and electric loadings is proposed. The governing equations are presented in terms of electromechanical generalized variables by the use of a suitable matrix notation. Thus, the three-dimensional electroelasticity solution for piezoelectric composite laminates is generated from a set of two partially coupled differential equations defined on the cross section of each individual ply within the laminate. These ply equations are linked through the interface conditions, which allow restoration of the model of the laminate as a whole. …
Numerical 2D And 3D Simulations of a Spherical Fabry–Pérot Resonator for Application as a Reference Cavity for Laser Frequency Stabilisation
2015
Abstract We report on the results of a numerical study of deformations of a spherical Fabry-Pérot cavity that can be used for laser frequency stabilisation. It is demonstrated that for a precise simulation of the cavity deformations a 3D model has to be used instead of a simpler 2D model, which employs simulation on the symmetry plane of the cavity. To lower the sensitivity to environmental perturbations, it is suggested to use a material with a low density and a high Young’s modulus. We also show that the mechanical resonance frequencies of the cavity are mainly determined by the size of the cavity.
Numerical analysis of light soaking phenomenon in Ruthenium based Dye Sensitized Solar Cells
2017
Dye Sensitized Solar Cells (DSSCs) are widely considered one of the most promising third generation photovoltaic devices, especially thanks to their relatively low cost if compared to conventional solar cells. An interesting phenomenon affecting such devices is the so-called light soaking effect, consisting in the increase of cell main electrical parameters after the exposition to solar light. In this work, starting from the experimental characterization carried out on Ruthenium-based DSSCs, we report on a series of numerical analysis performed to better describe the above-mentioned light soaking effect in order to show the relationship between such phenomenon and the main physical paramete…
Limits of the Open-Die Forward Extrusion: Numerical Analysis and Experimental Tests
1992
In the paper the open-die forward extrusion process is analysed in order to determine the influence of the most important geometrical and frictional parameters on the practical suitability of the operation. Experimental tests have been carried out and their results have been compared with the numerical ones derived by FEA.
Nonlinear Structural Mechanics Based Modeling of Carbon Nanotube Deformation
2003
A nonlinear structural mechanics based approach for modeling the structure and the deformation of single-wall and multiwall carbon nanotubes (CNTs) is presented. Individual tubes are modeled using shell finite elements, where a specific pairing of elastic properties and mechanical thickness of the tube wall is identified to enable successful modeling with shell theory. The effects of van der Waals forces are simulated with special interaction elements. This new CNT modeling approach is verified by comparison with molecular dynamics simulations and high-resolution micrographs available in the literature. The mechanics of wrinkling of multiwall CNTs are studied, demonstrating the role of the …
Numerical Modeling Approaches of FRCMs/SRG Confined Masonry Columns
2019
The Fabric Reinforced Cementitious Matrices (FRCMs) and Steel Reinforced Grout (SRG) are a promising strengthening solution for existing masonry since inorganic matrix is considerably compatible with historical substrates. The present paper is focused on a Finite Element (FE) analysis of masonry columns confined with FRCM composites developed by Abaqus-code. The masonry columns were modelled using a macro model approach. The model was performed by using the following functions Concrete Damage Plasticity (CDP) and the Plastic (P) in order to describe the constitutive laws of material for masonry columns and external reinforcement, respectively. Typical failures of FRCM-systems are slippage o…