Search results for "Optical"

<title>Safety problems in free space optical transmission</title>

2006

The paper is focused on safety of exploitation of optical transmission devices in free space. The subjects concerning propagation of "open" optical stream and its' possible dangerous influence on environment, mainly living organisms are discussed. An attempt to evaluate an installation and exploitation of transmitting devices was made, concerning dangers, requirements, recommendations and restrictions, concluding from accepted safety standards (IEC 60825- 1 :2005, EN 60825-1 :2005 and in Poland PN-EN 60825-1 :2005 "Safety of laser devices - Equipment classification, requirements and user's guide"; IEC 60825-12:2004, EN 60825-12:2005 and in Poland PN-EN 60825-12:2005 "Safety of free space op…

Analyses of Dual Polarization WDM and SCM Radio over Fiber and Radio over FSO for C-RAN Architecture

2016

En este trabajo se simulan y verifican experimentalmente los esquemas de transmisión para una Arquitectura de Red de Acceso Radio Centralizada (C-RAN) basados en la combinación de dos tecnologías: Radio sobre Fibra (RoF) y Radio sobre FSO (RoFSO). Las configuraciones propuestas se optimizan para la evolución a largo plazo (LTE) con un ancho de banda de 20 MHz utilizando una modulación de amplitud en cuadratura de 64-QAM en términos de magnitud de vector de error (EVM). En primer lugar, se comparan las mediciones de la multiplexación por división de polarización mediante la combinación de RoF y RoFSO (PDM-RoF/FSO) con los modelos de simulación. Esto se amplía con la combinación de PDM-Multip…

A tunnel magnetoresistive effect wattmeters-based wireless sensors network

2017

Abstract In the present work a wireless sensors network (WSN) for smart energy metering is presented using the ZigBee protocol as the communication link. Each network node process the electrical power by means of a Wheatstone bridge sensor based on the tunnel magnetoresistive (TMR) effect working as analogue multiplier. The electrical power is acquired and processed by a digital signal processor that extracts various parameters of interest like current and voltage load, active power and power factor by means of Fourier analysis. All the obtained electrical parameters at each node are served and shown in a web page that can be easily accessed by authorized users.

Design, fabrication, and analysis of a spin-valve based current sensor

2004

Abstract In this work, we suggest a novel current sensor design, based on spin valve technology, with a full Wheatstone bridge configuration. The principal characteristic is that the four magnetoresistance sensing elements, fully active, are deposited and patterned at the same time. This way, differences among them should be insignificant, so improving voltage offset and drift temperature parameters. The complete IC fabrication process involves only three lithography steps, making the process cheaper and faster. In order to get a balanced bridge, the measured current must be properly driven, by means of an auxiliary PCB. Some prototypes, with different input impedances, have been fabricated…

Analytical compact modeling of GMR based current sensors: Application to power measurement at the IC level

2010

An analytical compact model for giant magnetoresistance (GMR) based current sensors has been developed. Different spin-valve based full Wheatstone bridge sensors, with the current straps integrated in the chip, have been considered. These devices have been experimentally characterized in order to extract the model parameters. In this respect, we have focused on the sensors linear operation regime. The model, which allows the individual description of the magnetoresistive elements, has been implemented in a circuit simulator by means of a behavioral description language: Verilog-A. We also propose the use of the devices in a direct power measurement application at the integrated circuit (IC)…

Active power analog front-end based on a Wheatstone-type magnetoresistive sensor

2011

Abstract In the proposed work a practical magnetoresistive wattmeter based on a commercial sensor is designed to measure active power at industrial frequencies. The electronic conditioning circuit uses differential blocks in order to preserve the sensor initial common mode rejection ratio. A 700 W power level has been reached with an uncertainty less than 1%. With few changes the proposed circuitry could be used in metering applications.

Material characteristics in the analysis of heated steel beams

1989

Beam fire tests are expensive and complicated. They may be replaced by calculations of the heated beam deflection by means of the method presented in this paper. The following material characteristics in the analysis of the deflection of beams during fire may be taken as fundamental: the steel creep characteristic at elevated temperatures, the modulus of elasticity and the coefficient of thermal expansion. According to the yield hinge theory, the yield stress is the criterion of failure of steel beams in fire. On the other hand, in the analysis of the deflection of the heated steel beams the influence of the yield stress is very small. The influence of the respective material characteristic…

Frequency mapping in dynamic light emission with wavelet transform

2013

International audience; Dynamic photon emission microscopy is an e cient tool to analyse today's integrated circuit. Nevertheless, the reduction of transistor's dimensions leads to more complex acquisitions where many spots can be seen. A frequency characterization of the whole acquired area can help to have a better understanding of it. With that purpose in mind, a new methodology to draw frequency mapping of dynamic light emission acquisition is reported. It is fully automated and based on wavelet transform and autocorrelation function. Regarding the possible use in an industrial context, the suggested method can help to localize abnormal emission activity and it gives some perspectives o…

Efficient FDTD analysis of discontinuities in a square coaxial waveguide

1996

A low-cost compact uniplanar Quasi–Yagi printed antenna

2008

A low cost directive uniplanar broadband printed Quasi–Yagi antenna design is presented. As a particular realization, some prototypes have been designed to operate in the 2.45 GHz band. They have been then modeled, fabricated onto standard printed circuit dielectric substrate and tested successfully. For the design and the modeling processes, we have make use of FDTD based in-house developed algorithms. The obtained bandwidth is, for all the considered cases, better than 15%. The main radiation characteristics are 2–5.5 dBi gain, depending on the number of director elements, and better than 25 dB front-to-back ratio. Overall antenna size was, in any case lesser than 1 λ × 0.5 λ. © 2008 Wile…