Search results for "Orient"
showing 10 items of 2371 documents
Ranke, Burckhardt e il "rinascimento orientale"
2020
Il saggio ricostruisce le reazioni di Ranke e di Burckhardt al "Rinascimento Orientale" del romanticismo e della cultura del tardo Ottocento. I temi trattati riguardano il tema della violenza nella storia, il significato del "sacrificio", il pericolo dell'anonimato e del quantitativo nella vita metropolitana. Un riferimento importante è svolto nel saggio da Quinet, cui si ricorre come a un "fil rouge". What stance on “Eastern Renaissance” did Ranke and Burckhardt take? This subject needed to make a survey of the German-Romantic idea of the East, focusing on Herder’s anthropology. Notoriously, Ranke and Burckhardt were very different historians, but they shared a negative opinion on “Eastern…
Servisu orientētas arhitektūras veiktspēja
2017
Mūsdienās, veidojot informācijas sistēmas, nepieciešams tās veidot elastīgas un daudzfunkcionālas, lai varētu nodrošināt klientu vēlmes un spēt sekot līdzi strauji mainīgajai pasaulei. Lai to nodrošinātu, informācijas sistēmas bieži tiek veidotas balstoties uz Servisu orientētu arhitektūru, kurā sistēmas funkcionālā daļa tiek veidota atsevišķi un smalki sadalīta. Darbā apskatītas servisu orientētas arhitektūras, to realizācija un pielietojumi, veiktspējas problēmas, un risinājumi, kā tās samazināt. Izmantojot iegūto informāciju, veikts šo risinājumu salīdzinājums, kurš izmantots lēmumu koka izveidē. Balstoties uz iegūto lēmumu koku, izvēlēts viens no risinājumiem, kas izmantots informācijas…
Maximum Torque Per Ampere control algorithm for low saliency ratio interior permanent magnet synchronous motors
2017
This paper presents an investigation on the comparison between the Maximum Torque Per Ampere (MTPA) and the Field Orientation Control (FOC) algorithms for interior permanent magnet synchronous machines (IPMSMs). In particular, this study was carried out on a small-power IPMSM with low salience ratio. Both control algorithms have been implemented in the Matlab/Simulink environment, obtaining promising results.
A procedure for slicing and characterizing soft heterogeneous and irregular-shaped tissue
2020
Abstract This paper presents a slicing technique useful to prepare precise and repeatable samples from organs which are irregularly shaped and highly heterogeneous for mechanical testing and advanced microscopy observation. The suggested technique does not seem to influence the internal microstructure and it is employed here for testing specimens cut from different region of the meniscal tissue. Fast Fourier Transform analysis is used to quantify characteristic features of the microstructure (collagen fibers orientation, pore size) after slicing prior mechanical testing. Uniaxial (relaxation) tests are performed on dog-bone meniscal samples. Stress relaxation testing results on samples cut …
Stability analysis of a paramagnetic spheroid in a precessing field
2019
Abstract The stability of a paramagnetic prolate or oblate spheroidal particle in a precessing magnetic field is studied. The bifurcation diagram is calculated analytically as a function of the magnetic field frequency and the precession angle. The orientation of the particle in the synchronous regime is calculated. The rotational dynamics and the mean rotational frequency in the asynchronous regime are also obtained. The theoretical model we describe enables the analytic calculation of the dynamics of the particle in the limiting case when the motion is periodic. The theoretical models were also compared with experimental results of rod like particle dynamics in a precessing magnetic field…
Experimental comparison of two control algorithms for low-saliency ratio interior permanent magnet synchronous motors
2018
In this paper, an experimental investigation on the comparison between the Maximum Torque Per Ampere (MTPA) and the Field Orientation Control (FOC) algorithms for interior permanent magnet synchronous machines (IPMSMs) is described, analyzed and discussed. This investigation was carried out on a small-power IPMSM with low saliency ratio. More in detail, after a previous simulation study, the control techniques have been experimentally implemented and validated through means of a dSPACE® rapid prototyping system. The performances of the two algorithms have been evaluated and compared, obtaining interesting results.
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
Enhanced alignment and orientation of polar molecules by vibrational resonant adiabatic passage
2007
The authors show that polar molecules can be adiabatically aligned and oriented by laser pulses more efficiently when the laser frequencies are vibrationally resonant. The aligned molecules are found in a superposition of vibrational pendular states, each associated with the alignment of the rotor in one vibrational state. The authors construct the dressed potential associated with this mechanism. Values of detunings and field amplitudes are given to optimize the degree of alignment and orientation for the CO molecule.
Model building on the non-factorisable type IIA T6/(Z4×ΩR) orientifold
2016
We construct global semi-realistic supersymmetric models with intersecting D6-branes on the non-factorisable orientifold . The non-factorisable structure gives rise to differences compared to the factorisable case: additional conditions for the three-cycles to be Lagrangian and extra constraints on the wrapping numbers for building fractional cycles.
The joint sets on the Lilstock Benches, UK. Observations based on mapping a full resolution UAV-based image
2021
Outcrop studies of fracture networks are important to understand fractured reservoirs in the subsurface, but complete maps of all fractures in large outcrops are rare due to limitations of outcrop and image resolution. We manually mapped the first full-resolution UAV-based, Gigapixel dataset and DEM of the wave-cut Lilstock Benches in the southern Bristol Channel basin, a classic outcrop of layer-bound fracture networks in limestones. We present a map of the patterns and age relationships of successive sets of joints in dm-thick limestone layers separated by claystone beds. Using interpretation criteria based on crosscutting relationships, abutting and joint length, up to eight successive s…