Search results for "Oxide"

Borate-driven gatelike scaffolding using mesoporous materials functionalised with saccharides.

2009

We report the development of an MCM-41 mesoporous support that is functionalised with saccharides at the pore outlets and contains the dye [Ru(bipy)(3)](2+) in the pores (solid S1; bipy = 2,2'-bipyridyl). For this hybrid system, the inhibition of mass transport of the dye from the pore voids to the bulk solution in the presence of borate is demonstrated in water at neutral pH. The formation of the corresponding boroester derivative is related to the selective reaction of borate with the appended saccharides. This control is selective and only anion borate, among several anions and cations, can act as a molecular tap and inhibit the delivery of the entrapped guest. Additionally, the S1-borat…

N-Propyl-N′-2-pyridylurea-modified silica as mixed-mode stationary phase with moderate weak anion exchange capacity and pH-dependent surface charge r…

2018

Herein, we present a novel silica-based stationary phase modified with N-propyl-N'-2-pyridylurea selector. Due to the weakly basic properties of the pyridine selector and the presence of residual silanols after selector immobilization, a zwitterionic surface with a pI observed at approximately pH 5.5 was measured by electrophoretic light scattering in pH-dependent ζ-potential determinations. The capability of the new N-propyl-N'-2-pyridylurea-modified silica to serve as mixed-mode stationary phase was investigated. For this purpose, it was characterized under RP and HILIC conditions using test mixtures. Subsequent classification of this stationary phase in comparison to in-house and commerc…

Surface-anchored counterions on weak chiral anion-exchangers accelerate separations and improve their compatibility for mass-spectrometry-hyphenation

2017

In the present work we propose new variants of chiral stationary phases (CSP) with tert-butylcarbamoylquinine (tBuCQN) as chiral selector molecule. Four tBuCQN-CSPs with distinct bonding chemistries are compared in terms of their pH-dependent surface charge by ζ-potential determinations, by achiral and chiral liquid chromatographic tests and LC-ESI-MS hyphenation. In one embodiment tBuCQN was immobilized on 3-mercaptopropylmethylsilyl-modified silica by thiol-ene click reaction (brush type CSP with selector coverage of 0.38mmol/g). In another embodiment, poly-(3-mercaptopropyl)-methylsiloxane was coated onto vinylized silica particles in presence of tBuCQN and radical initiator. The tBuCQN …

Determination of low-molecular-mass aliphatic carboxylic acids and inorganic anions from kraft black liquors by ion chromatography.

2007

An ion chromatographic (IC) method with suppressed conductivity detection (CD) was developed and validated for the quantitative determination of several low-molecular-mass aliphatic mono- and dicarboxylic acids as their carboxylate anions together with some inorganic anions (chloride, sulfate, and thiosulfate) from kraft black liquors. To confirm the identification of some carboxylate anions which lack commercial model substances, a qualitative IC method with suppressed electrospray ionization mass spectrometry (ESI-MS) was also developed. The separations were performed on an IonPac AS 11-HC anion-exchange column operated at 25 degrees C within 25 min by a gradient elution with aqueous pota…

Should TiO2 nanostructures doped with Li+ be used as photoanodes for photoelectrochemical water splitting applications?

2017

[EN] Different TiO2 nanostructures, nanotubes and nanosponges, were obtained by anodization of Ti under stagnant and hydrodynamic conditions. Samples were doped with Li+ before and after annealing at 450 degrees C during 1 h. The nanostructures were characterized by different microscopy techniques: Field Emission Scanning Electron Microscopy (FE-SEM) and Raman Confocal Laser Microscopy. Additionally, Incident Photon-to-electron Conversion Efficiency (IPCE), photoelectrochemical water splitting and stability measurements were also performed. According to the results, TiO2 nanostructures doped before annealing present the worst photocurrent response, even if compared with undoped samples. On …

Dimensionless Analysis Of Slurry Photocatalytic Reactors Using Two-Flux And Six-Flux Radiation Absorption-Scattering Models

2007

Photocatalytic oxidation (PCO) over titanium dioxide (TiO2) is a "green" sustainable process for the treatment and purification of water and wastewater. However,the application of PCO for wastewater treatment on an industrial scale is currently hindered by a lack of simple mathematical models that can be readily applied to reactor design. Current models are either too simplistic or too rigorous to be useful in photocatalytic reactor design, scale-up, and optimization. In this paper a simple mathematical model is presented for slurry, annular, photocatalytic reactors that still retains the essential elements of a rigorous approach while providing simple solutions. The model extends the appli…

Characterization of Anodic Oxides on Titanium by Photocurrent and Differential Admittance Techniques

2010

Characterization of Anodic Oxides on Magnetron Sputtered Ta-Nb Alloys by Photocurrent Spectroscopy and Differential Admittance Measurements

2010

Ruthenium Oxide Nanotubes Via Template Electrosynthesis

2011

Ruthenium oxide nanotubes were fabricated by a single-step galvanostatic deposition using porous anodic alumina membrane as template. For the electrodeposition process, we used a electrochemical cell specifically designed in order to employ only 0.5 ml of 0.02 M RuCl3•xH2O solution. The deposition from a very small volume was specifically addressed owing to the high cost of ruthenium compounds, which could be of some relevance from an applicative point of view. Several techniques were used to characterize the samples prior to and after thermal treatment, which was carried out at different temperatures in order to study the crystallization process of the deposit. Raman spectroscopy of as-dep…

Microporous alumina membranes electrochemically grown

2003

Abstract The electrochemical fabrication of alumina membranes by anodizing of aluminium in phosphoric acid and oxalic acid solutions, in the temperature interval from −1 to 16 °C, was investigated in order to study the influence of different parameters (initial treatment of aluminium surface, nature and composition of electrolyte, temperature) on the final characteristics of the membranes. Porous layers were grown using a linear potential scan at 0.2 V s −1 up to 160 V in H 3 PO 4 solution and 70 V in oxalic acid solution. The efficiency of porous layer formation was calculated by using Faraday's law and weight measurements. Pore size distribution and porosity of membranes prepared in 0.4 M…