Search results for "PHOTOELECTRON"
showing 10 items of 458 documents
3d impurities in Al: density functional results
1980
Self-consistent spin density functional calculations have been carried out for 3d transition metal impurities in aluminium. The width of the virtual level decreases as it moves away from the Fermi energy with increasing occupancy. The results are compared with recent XPS measurements.
A nondestructive analysis of the B diffusion in Ta–CoFeB–MgO–CoFeB–Ta magnetic tunnel junctions by hard x-ray photoemission
2010
This work reports on hard x-ray photoelectron spectroscopy (HAXPES) of CoFeB based tunnel junctions. Aim is to explain the role of the boron diffusion for the observed improvement of the tunneling magnetoresistance ratio with increasing annealing temperature. The high bulk sensitivity of HAXPES was used as a nondestructive technique to analyze CoFeB–MgO–CoFeB magnetic tunnel junctions. The investigated samples were processed at different annealing temperatures from 523 to 923 K. Hard x-ray core level spectroscopy reveals an enforced diffusion of boron from the CoFeB into the adjacent Ta layer with increasing annealing temperature. The dependence of the tunneling magnetoresistance on the ann…
Influence of ZnO/graphene nanolaminate periodicity on their structural and mechanical properties
2018
International audience; Structural, electronic and mechanical properties of ZnO/Graphene (ZnO/G) nanolaminates fabricated by low temperature atomic layer deposition (ALD) and chemical vapor deposition (CVD) were investigated. We performed scanning and transmission electron microscopy (SEM/TEM), X-ray diffraction (XRD), electron energy loss spectroscopy (EELS), Raman spectroscopy, X-Ray photoelectron spectroscopy (XPS) and nanoindentation to characterize the ZnO/G nanolaminates. The main structural and mechanical parameters of ZnO/G nanolaminates were calculated. The obtained results were analyzed and interpreted taking into account mechanical interaction and charge effects occurring at the …
Phase mixture in MOCVD and reactive sputtering TiOxNy thin films revealed and quantified by XPS factorial analysis.
2006
Abstract Titanium oxynitride thin films have been deposited by low-pressure metalorganic chemical vapour deposition and reactive sputtering. The growth temperature for chemical vapour-deposited films and water vapour partial pressure for sputter-deposited films have been used to modulate the chemical composition. Both series have been analysed using X-ray photoelectron spectroscopy (XPS) in order to describe the structure of the materials using a factorial analysis approach. Titanium and metalloid concentrations have also been determined and compared to an elemental analysis performed using Rutherford backscattering spectroscopy and nuclear reaction analysis. The two deposition methods led …
Investigation of Acetone Vapour Sensing Properties of a Ternary Composite of Doped Polyaniline, Reduced Graphene Oxide and Chitosan Using Surface Pla…
2020
This work reports the use of a ternary composite that integrates p-Toluene sulfonic acid doped polyaniline (PANI), chitosan, and reduced graphene oxide (RGO) as the active sensing layer of a surface plasmon resonance (SPR) sensor. The SPR sensor is intended for application in the non-invasive monitoring and screening of diabetes through the detection of low concentrations of acetone vapour of less than or equal to 5 ppm, which falls within the range of breath acetone concentration in diabetic patients. The ternary composite film was spin-coated on a 50-nm-thick gold layer at 6000 rpm for 30 s. The structure, morphology and chemical composition of the ternary composite samples were character…
Surface characterization of functional poly(diacetylene) and poly(butadiene) mono- and multilayers
1982
The surface properties of Langmuir-Blodgett mono- and multilayers of a variety of amphiphilic poly(diacetylene)s and poly(butadiene)s were investigated by contact angle, streaming potentialζ, ellipsometry, and X-ray photoelectron spectroscopic (XPS) measurements. Captive air and octane angles varied between approximately 60° and 105° for hydrophobicx-layers and 31° to 46° for hydrophilic surfaces depending on the particular head group, whereas advancing angles determined via the vertical plate method are considerably higher. Negative streaming potentials were obtained for all surfaces. Positively charged monolayers yielded less negativeζ- potential values (−28 mV) than negatively charged (−…
Ultrathin metal films and inorganic clusters via thermodesorption of LB films
1991
Langmuir-Blodgett multilayers of cadmium arachidate and ferric stearate were investigated during heating in order to derive information on processes involved in thermodesorption and on the inorganic microstructures left on the substrate after thermodesorption. We studied these processes by X-ray induced photoelectron spectroscopy (XPS), interference enhanced reflection (IeR), Nomarsky microscopy, electron microprobe analysis and in the case of Fe57-ions by conversion electron Mossbauer spectroscopy (CEMS). Two different mechanisms of desorption were observed. In the case of cadmium arachidate multilayers it is shown that before desorption the film ruptures laterally and then forms droplets.…
Formation and Characterization of Self-Assembled Films of Thiol-Derivatized Poly(Dimethylsiloxane) on Gold
1997
Poly(dimethylsiloxane) (PDMS) copolymers containing propanethiol side chain “stickers” for forming self-assembled films on gold surfaces have been studied by various experimental techniques including ellipsometry, contact angle measurements, FT-IR, angle-dependent XPS, and ToF−SIMS. The results show that the thiol-containing side chains do not all chemisorb to the gold surfaces. In addition, the concentration of these sticker units was found to have a dominant effect on the polymer film thickness, the surface wetting properties, and the orientation of the PDMS backbone. Ab initio calculations reveal that the IR-active PDMS Si−O stretching bands can be used as indications of chain orientatio…
A new method of nanocrystalline nickel powder formation by magnetron sputtering on the water-soluble substrates
2018
Due to the accurate and relatively easy control magnetron sputtering is an attractive technique for the synthesis of metallic particles. This work describes a new method of nickel powder production by depositing nickel on the surface of sodium chloride particles which were used as the template and are soluble in water. Ni powder with flake-like structure was obtained after washing Ni coated salt particles in ultrasonic cleaner. Salt particles and nickel powder were characterized using scanning electron microscope (SEM), energy-dispersive x-ray spectrometer, XRD and X-ray photoelectron spectroscopy (XPS) techniques. SEM images showed that thickness of the received Ni particles varied in the …
XPS and EELS investigations of chemical homogeneity in nanometer scaled Ti-ferrites obtained by soft chemistry
1999
Abstract Nanocrystalline Ti-ferrites with composition Fe 3− x Ti x O 4 with 0≤ x ≤1 are synthesized using the soft chemistry route. Heterogeneities in precipitate and annealed powders are investigated by a combination of XPS and EELS techniques. As-prepared powder consists in particles with spinel structure and grain size of about 15 nm. Due to high reactivity towards oxygen of nanoparticules, a significant amount of Fe 2+ cations oxidize during precipitation, so that precipitated powders present large deviation from oxygen-metal stoichiometry. Moreover precipitated particles are evidenced to exhibit a strong surface titanium enrichment and an iron richer core. Observation of such cation se…