Search results for "Phase Transition"
showing 10 items of 1281 documents
Comparative study of the high-pressure behavior of ZnV2O6, Zn2V2O7, and Zn3V2O8
2020
We report a study of the high-pressure structural behavior of ZnV2O6, Zn2V2O2, and Zn3V2O8, which has been explored by means of synchrotron powder x-ray diffraction. We found that ZnV2O6 and Zn3V2O8 remain in the ambient-pressure structure up to 15 GPa. In contrast, in the same pressure range, Zn2V2O2 undergoes three phase transitions at 0.7, 3.0, and 10.8 GPa, respectively. Possible crystal structures for the first and second high-pressure phases are proposed. Reasons for the distinctive behavior of Zn2V2O2 are discussed. The compressibility of the different polymorphs has been determined. The response to pressure is found to be anisotropic in all the considered compounds and the room-temp…
High-pressure structural and elastic properties of Tl2O3
2014
The structural properties of Thallium (III) oxide (Tl2O3) have been studied both experimentally and theoretically under compression at room temperature. X-ray powder diffraction measurements up to 37.7 GPa have been complemented with ab initio total-energy calculations. The equation of state of Tl2O3 has been determined and compared to related compounds. It has been found experimentally that Tl2O3 remains in its initial cubic bixbyite-type structure up to 22.0 GPa. At this pressure, the onset of amorphization is observed, being the sample fully amorphous at 25.2 GPa. The sample retains the amorphous state after pressure release. To understand the pressure-induced amorphization process, we h…
Solubility of solid carnosic acid in supercritical CO2 with ethanol as a co-solvent
2005
Abstract The present study is devoted to the experimental measurement and thermodynamic modeling of solid carnosic acid solubility in supercritical CO 2 + ethanol as a co-solvent. Measurements were carried out at temperatures in the range of 313.15 and 333.15 K, pressures ranging from 280 to 400 bar, and at different content of the modifier ethanol (from 0.7 to 10%). The Group Contribution Associating Equation of State (GCA-EoS) [H.P. Gros, S.B. Bottini, E.A. Brignole, High pressure phase equilibrium modeling of mixtures containing associating compounds and gases, Fluid Phase Equilibria 139 (1997) 75–87] was applied in this work to represent the experimental solubility data obtained. Due t…
Modelling of phase transitions and residual thermal stress of CTBN rubber modified epoxy resins during a pultrusion process
2007
Abstract The implicit finite difference and fourth order Runge-Kutta method are used both to solve the heat transfer problem in the pultrusion reaction and to calculate the temperature and conversion distributions within a thermoset composite profile. The aim of our work is to study the influence of a rubbery phase added to the epoxy matrix in production conditions. The results have shown that the rubber modified systems have a low exothermic temperature peak value, so that neither the amount of cured resin nor the final product properties are limited. First of all we will show that the phase transition (gelation and vitrification) zones within the die change as the amount of rubber varies …
Inspection of additive-manufactured layered components
2015
Laser powder deposition (LPD) is a rapid additive manufacturing process to produce, layer upon layer, 3D geometries or to repair high-value components. Currently there is no nondestructive technique that can guarantee absence of flaws in LPD products during manufacturing. In this paper a laser ultrasonic technique for in-line inspection of LPD components is proposed. Reference samples were manufactured from Inconel and machined flaws were created to establish the sensitivity of the technique. Numerical models of laser-generated ultrasonic waves have been created to gain a deeper understanding of physics, to optimize the set-up and to verify the experimental measurements. Results obtained on…
Pulsed Laser Deposition of Cs 2 AgBiBr 6 : from Mechanochemically Synthesized Powders to Dry, Single-Step Deposition
2021
Cs2AgBiBr6 has been proposed as a promising lead-free and stable double perovskite alternative to hybrid and lead-based perovskites. However, the low solubility of precursors during wet synthesis, or the distinct volatility of components during evaporation, results in complex multistep synthesis approaches, hampering the widespread employment of Cs2AgBiBr6 films. Here, we present pulsed laser deposition of Cs2AgBiBr6 films as a dry, single-step and single-source deposition approach for high-quality film formation. Cs2AgBiBr6 powders were prepared by mechanochemical synthesis and pressed into a solid target maintaining phase purity. Controlled laser ablation of the double perovskite target i…
Deposition of indium tin oxide films by laser ablation: Processing and characterization
1998
Abstract In this work an indium tin oxide thin film fabrication technique based on pulsed laser deposition is described and the electrical, optical and mechanical properties of the deposited films are reported. Deposition of high quality films on cold substrates was proved. The third harmonic (355 nm) of an Nd:YAG laser was employed to photoablade the indium tin oxide target.
One-step large-scale deposition of salt-free DNA origami nanostructures
2015
AbstractDNA origami nanostructures have tremendous potential to serve as versatile platforms in self-assembly -based nanofabrication and in highly parallel nanoscale patterning. However, uniform deposition and reliable anchoring of DNA nanostructures often requires specific conditions, such as pre-treatment of the chosen substrate or a fine-tuned salt concentration for the deposition buffer. In addition, currently available deposition techniques are suitable merely for small scales. In this article, we exploit a spray-coating technique in order to resolve the aforementioned issues in the deposition of different 2D and 3D DNA origami nanostructures. We show that purified DNA origamis can be …
The domain structure in PLZT (6-8)/65/35 and spontaneous ferroelectric-relaxor phase transition
1995
Abstract In order to test the hypothesis proposed in Reference 10 about a spontaneous relaxor-ferroelectric phase transition in PLZT (6-7)/65/35 the hysteresis loops and domain structure measurements were carried out. The results confirm this hypothesis. The appearance of the ferroelectric long range order in PLZT with decreasing concentration of La ions is explained by a larger coupling between the feroelectrically active BO6 octahedrons due to smaller concentration of defects and higher dielectric constant.