Search results for "Piping"
showing 10 items of 41 documents
Advanced numerical models for the thermo-mechanical-metallurgical analysis in hot forging processes
2013
In the paper a literature review of the numerical modeling of thermo-mechanical-metallurgical evolutions of a metal in hot forging operations is presented. In particular models of multiaxial loading tests are considered for carbon steels. The collected examples from literature regard phases transformations, also martensitic transformations, morphologies evolutions and transformation plasticity phenomena. The purpose of the tests is to show the correlation between the mechanical and the metallurgical behavior of a carbon steel during a combination of several types of loads. In particular a few mechanical tests with heat treatment are analyzed. Furthermore, Ti-6Al-4V titanium alloy is conside…
Induced roughness in thin films of smectic-C* elastomers
2002
The surface topography of a thin homeotropically oriented film of ferroelectric smectic-C* elastomer is studied by atomic force microscopy. We find that when the film is mechanically stretched, its surface becomes increasingly rough, in proportion to the applied strain. The effect depends strongly on the nature of crosslinks forming the elastomer network. The r.m.s. roughness correlations show a consistent trend [h(x) − h(0)]21/2 ~ (x/ξ)0.5. We introduce a theoretical model assuming that random disorder in the smectic tilt angle is induced by deformations via the coupling of mesogens to the elastic network. The model describes the observed power law and gives a prediction for the correlatio…
Investigation of self-healing mechanism on galvanized steels cut edges by coupling SVET and numerical modeling
2008
Local cathodic inhibition has been observed on the cut-edge of galvanized steel immersed in 0.03 M NaCl solution using the scanning vibrating electrode technique. The current distribution results indicate that cathodic inhibition occurs in a limited spatial zone located between the cathodic sites on the steel and the anodic sites on the exposed zinc surface. The experimental current distributions are compared with the results of numerical simulations that show the specific diagnostic features for the detection of cathodic inhibition from scanning vibrating electrode technique (SVET) data so as to distinguish the zero current regions from experimental artifacts due to the lateral resolution …
On the Use of L-shaped Granular Chains for the Assessment of Thermal Stress in Slender Structures
2014
Slender beams subjected to compressive load are common in civil engineering. The rapid in-situ measurement of this stress may help preventing structural anomalies. In this article, we describe the coupling mechanism between highly nonlinear solitary waves (HNSWs) propagating along an L- shaped granular system and a beam in contact with the gran- ular medium. We evaluate the use of these waves to measure stress in thermally loaded structures and to estimate the neutral temperature, i.e. the temperature at which the stress is null. We investigate numerically and experimentally one and two L- shaped chains of spherical particles in contact with a prismatic beam subjected to heat. We find that …
Molecular Dynamics Computer Simulation of Cooling Rate Effects in a Lennard-Jones Glass
1995
We present the results of a molecular dynamics computer simulation of a binary Lennard-Jones mixture. We simulate a quench of the system from a liquid state at high temperatures to a glass state at zero temperature by coupling the system to a heat bath that has a temperature that decreases linearly (with slope -γ) with time. We investigate how the residual density of the system varies as a function of the cooling rate γ and rationalize our results by means of the dependence of the coordination number of the particles on the cooling rate.
Electron–phonon interaction in a thin Al–Mn film
2006
Abstract Aluminum doped with manganese is an interesting novel material with applications in normal metal–insulator–superconductor (NIS) tunnel junction devices and transition-edge sensors at sub-Kelvin temperatures. We have studied the electron–phonon (e–p) coupling in a thin aluminum film doped with 1% manganese, with a measuring technique based on DC hot-electron effect. The electron temperature was measured with the help of symmetric normal metal–insulator–superconductor tunnel-junction pairs (SINIS-thermometers). Measurements show that the temperature dependence of the e–p interaction is not consistent with existing theories for disordered metals, but follows a higher power law.
Assessment of DEMO WCLL breeding blanket primary heat transfer system isolation valve absorbed doses due to activated water
2020
Abstract Within the framework of the activities foreseen by the EUROfusion action on the cooling water activation assessment for a DEMO reactor equipped with a Water Cooled Lithium Lead Breeding Blanket (WCLL BB), the University of Palermo is involved in the investigation of the absorbed dose induced by the decay of nitrogen radioisotopes produced by water activation, in the main components (e.g. isolation valves) of both First Wall (FW) and Breeder Zone (BZ) cooling circuits. The aim of this work is to assess the spatial distribution of the absorbed dose in the DEMO Upper Pipe Chase (UPC), focusing the attention on the space neighbouring a typical isolation valve of the Primary Heat Transf…
A computational procedure for the investigation of whipping effect on ITER High Energy Piping and its application to the ITER divertor primary heat t…
2015
Abstract The Tokamak Cooling Water System of nuclear facility has the function to remove heat from plasma facing components maintaining coolant temperatures, pressures and flow rates as required and, depending on thermal-hydraulic requirements, its systems are defined as High Energy Piping (HEP) because they contain fluids, such as water or steam, at a pressure greater than or equal to 2.0 MPa and/or at a temperature greater than or equal to 100 °C, or even gas at pressure above the atmospheric one. The French standards contemplate the need to consider the whipping effect on HEP design. This effect happens when, after a double ended guillotine break, the reaction force could create a displa…
Axial dispersion model for solid flow in liquid suspension in system of two mixers in total recycle
2006
The measurement of residence time distribution of solid particles in solid-liquid suspension is experimentally difficult. However, the twin system approach is particularly suited for the assessment of particle RTD in flow systems as it allows overcoming some of the usual difficulties generally encountered in this kind of measurement. Twin system consists of two vessels and external piping in total recycle. Experimental results from this system can be evaluated using Z-transforms to derive particle RTD for subsequent testing of alternative flow models. Recently, the axial dispersion model was applied using the "advection diffusion equation" (sometimes called the"diffusion with bulk flow equa…
Platform switching on wide-diameter external hex implants: a finite element analysis.
2012
Objectives: The objective of this work was to use finite element analysis to compare the effect of forces coming to bear on abutments 4.1 or 5.0 mm in diameter connected to a 5.0 mm implant (i.e. with or without platform swit - ching). Study design: A 3D CAD model of a 5 x 11.5 mm external hex implant was developed, complete with a connection screw and either of two abutments, one 4.1 and the other 5 mm in diameter, to assess the influence of two loading conditions, i.e. 200 N loaded either axially or off center on the top of the abutment. Results and conclusions: In the symmetrically loaded models, greater stresses were transmitted to the bone in the area below the neck of the implant in t…