Search results for "Polymer Blends"
showing 10 items of 37 documents
Recycling polymer blends
2014
Relaxation of photogenerated carriers in P3HT:PCBM organic blends.
2009
Relaxing in the sunlight. Long time-transient decays of photogenerated carriers in P3HT:PCBM blends for organic solar cells are interpreted in terms of the relaxation of hole carriers in a broad density of states. The after-pulse time-resolved microwave conductivity (TRMC) decays observed in P3HT:PCBM blends display a dependence on time close to t−β, independent of excitation intensity, in the 10 ns–1 μs range. This is explained in terms of the relaxation of carriers in a Gaussian density of states (DOS). The model is based on a demarcation level that moves with time by thermal release and retrapping of initially trapped carriers. The model shows that when the disorder is large the after-pu…
The Impact of Janus Nanoparticles on the Compatibilization of Immiscible Polymer Blends under Technologically Relevant Conditions
2014
Several hundred grams of Janus nanoparticles (d ≈ 40 nm) were synthesized from triblock terpolymers as compatibilizers for blending of technologically relevant polymers, PPE and SAN, on industry-scale extruders. The Janus nanoparticles (JPs) demonstrate superior compatibilization capabilities compared to the corresponding triblock terpolymer, attributed to the combined intrinsic properties, amphiphilicity and the Pickering effect. Straightforward mixing and extrusion protocols yield multiscale blend morphologies with "raspberry-like" structures of JPs-covered PPE phases in a SAN matrix. The JPs densely pack at the blend interface providing the necessary steric repulsion to suppress droplet …
Compatibilization of Polypropylene/Polyamide 6 Blend Fibers Using Photo-Oxidized Polypropylene.
2018
The use of polyamide/polyolefin blends has gained importance and concern for years, but they also show some issues to be adequately addressed, such as the incompatibility between the two components. This is usually overcome by using suitable compatibilizers, typically based on functionalized polyolefins. However, there is only little information about the use of a degraded polyolefins to induce compatibilization. This is even truer, as far as polyamide 6/polypropylene (PA6/PP) blends are concerned. In this work, compatibilization of PA6/PP blends by using small amounts of photo-oxidized PP was investigated
Reactive blending of a functionalized polyethylene with a semiflexible liquid crystalline copolyester
1996
Reactive blends (50/50 w/w) of a low molar mass polyethylene containing free carboxylic groups (PEox) and a semiflexible liquid crystalline polyester (SBH 1 : 1 : 2, by Eniricerche) have been prepared at 240 degrees C in a Brabender mixer, in the presence of Ti(OBu)(4) catalyst, for different mixing times (15, 60, and 120 min). In order to prove the formation of a PE-g-SBH copolymer, the blends have been fractionated by successive extractions with boiling toluene and xylene. The soluble fractions and the residues have been analyzed by Fourier transform infrared (FTIR) spectroscopy, thermogravimetry (TG and DTG), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM)…
PREPARATION AND CHARACTERIZATION OF CLAY NANOCOMPOSITES BASED ON COMPATIBILIZED POLYAMMIDE6/POLYETHYLENE BLENDS
2008
Photo-oxidation behaviour of polyethylene/polyamide 6 blends filled with organomodified clay: Improvement of the photo-resistance through morphology …
2010
Abstract The impact of small amounts of organomodified clay (OMMT) on the photo-degradation behaviour of two blends obtained by mixing either low-density polyethylene (LDPE) or high density polyethylene (HDPE) with polyamide 6 (PA6) (LDPE/PA6 and HDPE/PA6 75/25 wt-%) was studied. The complex photo-degradation behaviour was followed by monitoring the main physical–mechanical properties of the blends. In particular, mechanical and spectroscopic tests were performed in conditions of accelerated artificial aging. An accurate mechanical and morphological characterization was previously carried out. The presence of the OMMT promotes the unexpected formation of a co-continuous morphology for the H…
Low-density polyethylene/polyamide/clay blend nanocomposites: Effect of morphology of clay on their photooxidation resistance
2017
The photooxidation behaviour of low-density polyethylene (LDPE)/polyamide (PA) blends, containing polyamide 11 (PA11) or polyamide 6 (PA6), has been investigated in the absence and presence of a small amount of commercial organomodified clay (OMMT). The polymer blends LDPE/PA11 and LDPE/PA6 at 75/25 wt./wt.%, with and without OMMT, have been prepared by a two-step procedure: extrusion and sheet formulation. The formulated complex systems have been subjected to accurate morphological analysis in order to evaluate the effect of the OMMT presence on the refinement of the blend morphology. Furthermore, the produced sheets have been subjected to arterial UVB exposure and the variations of the me…
Modification of EVOH copolymers with e-caprolactone: synthesis and compatibilization effects in PE/PVC blends
2001
Polyethylene-polycaprolactone graft copolymers with different chemical structures (i.e. different number and length of PCL grafts and molecular weight of PE backbone) were synthesized from various EVOH copolymers and e-caprolactone, using Aluminum isopropoxide as catalyst, and were tested for their compatibilizing capability in PE/PVC blends. PE and PCL segments in the graft copolymers were found completely immiscible, while PCL segments of the graft copolymers were found completely miscible with PVC. When graft copolymers were added to PE/PVC blends they proved to be good agents for the dispersion of PVC phase in the PE matrix. SEM showed also improved adhesion between the dispersed PVC ph…