Search results for "Polymers"

Shear flow characterization of blends containing liquid crystal polymers

1992

A simple phenomenological approach is proposed in order to predict the presence of minima in the viscosity-composition curves of blends of thermoplastic with liquid crystal polymer (LCP). When the viscosity of the liquid crystal polymer is larger than that of the thermoplastic matrix, a minimum is observed. A possible explanation of the presence of yield stress in the flow curves of these blends is also given.

Gamma radiation of EVA-AA/MMA swollen systems to obtain mechanically improved blends

2002

In this work a "new" way to obtain "compatibilised" blends of rubber-glassy thermoplastic components is presented. Polyethylen-vinyl acetate acrylic acid terpolymer is swollen by methylmetacrylate and the system is irradiated through gamma rays in order to induce polymerisation of the monomer. Solubility and dynamic mechanical tests indicate the formation of a two phase system, even though in presence of strong interactions between the two components. Mechanical tensile behaviour is that of a ductile material with appreciable modulus values.

Thermal properties of e-beam cured epoxy/thermoplastic matrices for advanced composite materials

2007

The aim of this work is to investigate the possibility to improve the thermal behaviour of epoxy based systems, cured by ionizing radiation, in order to produce matrices for advanced carbon fibres composites. Blends of two epoxy monomers, difunctional and trifunctional, have been polymerized by e-beam irradiation and the dynamic mechanical thermal properties have been investigated. The increase of the concentration of the trifunctional epoxy monomer in the blend causes a marked increase of the Tg, but strongly decreases the reactivity. Subsequently, blends of the same epoxy monomers with a high Tg thermoplastic toughening agent have been considered and their reactivity and the thermal prope…

Synthesis of reactive hyperbranched and star-like polyethers and their use for toughening of vinylester–urethane hybrid resins

2004

A vinylester – urethane hybrid resin (VEUH) was toughened by adding various vinyl-functionalized branched polyethers in 10 and 20 wt%. Two sets of hyperbranched polymers (HBPs) with different branching density were compared with a set of six-arm star polymers. Besides the architecture, the polymers also varied in their characteristics (molecular mass and mass distribution, vinyl/hydroxy ratio). The morphology of the modified VEUH was studied by dynamic-mechanical thermal analysis (DMTA), transmission (TEM) and scanning electron microscopy (SEM). The toughness was characterized by the fracture energy ðGcÞ determined on compact tension specimens at room temperature. It was established that th…

Effects of organoclay on morphology and properties of nanocomposites based on LDPE/PA-6 blends without and with SEBS-g-MA compatibilizer

2009

LDPE/PA-6 blends (75/25 wt/wt) were added with SEBS-g-MA (S) and/or an organoclay (20A) using different compounding sequences and the morphology and the properties of the blends or composites were investigated. An XRD study of the nanocomposites with pure polymers showed that 20A is intercalated by LDPE or PA-6 chains, whereas it is exfoliated by S if the clay concentration does not exceed 10 wt%. The SEM investigation showed that both S and 20A behave as efficient emulsifying agents for the LDPE/PA-6 blends. However, their effect on the mechanical properties was found to be opposite: S enhanced toughness but lowered the stiffness, whereas 20A improved the elastic modulus but impaired the i…

Characterization of ultra-high-molecular-weight polyethylene (UHMWPE) modified by ion implantation

2004

Abstract Surface modification of ultra high molecular weight polyethylene (UHMWPE) is induced by ion implantation of different ions at 300 keV energy. The aim of this work was the chemical, physical and mechanical characterization of the modified material in order to know deep inside about the effect of the ion beam upon the polymer. The irradiated surfaces are investigated by Raman spectroscopy, infrared absorption and micro-hardness analysis, scanning electron microscopy. Pin on disc measurements valuated the wear of the UHMWPE against a stainless steel probe; wear resistance increases of about 76% after the ion implantation. This result can be attributed to the ion bombardment inducing a…

Time–carbonyl groups equivalence in photo-oxidative aging of virgin/recycled polymer blends

2004

AbstractThe photo-oxidation behaviour of polymers is strongly dependent on the initial amount of carbonyl groups along the chains. The growing use of recycled post-consumer polymers coming from products used outdoors and then photo-oxidised, both pure and blended with the same virgin polymer, gives rise to an unpredictable behaviour of weathering resistance of products made with these materials. The present work shows that the carbonyl group–exposure time curves can be shifted along the time axis to give a single generalised master plot. It is then possible to predict the formation of the new carbonyl groups by knowing only the initial amount of the same carbonyl groups. The same shift fact…

Observation of Very Narrow Linewidths in the Fluorescence Excitation Spectra of Single Conjugated Polymer Chains at 1.2 K

2007

Fluorescence emission and excitation spectra of single poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] polymer molecules embedded in poly(methylmethacrylate) have been recorded at 1.2 K. The ubiquitous spectral diffusion causes large variations in the spectral shape and apparent linewidth in the emission spectra. Nevertheless, we find very narrow (approximately 0.1 cm(-1)) purely electronic zero-phonon lines in the excitation spectra, which are 2 orders of magnitude smaller than previous estimates of the homogeneous linewidth. These results complement the molecular description of the low energy transitions in conjugated polymers.

Frontispiece: Hierarchy of Asymmetry at Work: Chain-Dependent Helix-to-Helix Interactions in Supramolecular Polymers

2018

LARGE DEFORMATION CREEP BEHAVIOR OF A SOLID POLYMER.

1981

Abstract The effect of loading rate and strain on the creep behavior after sample yielding has been studied in previous communications (14–15) for Mylar in tension and for Lexan in compression. In this work the creep behavior of Lexan samples previously elongated is considered both in tension and in compression. A procedure which collects all the data independently of both loading rate and initial creep strain is proposed.