Search results for "Power electronic"
showing 10 items of 91 documents
Low-Power Design of Delay Interpolating VCO
2008
In this paper, a design methodology for low-power MCML based delay interpolating VCOs is presented. The methodology allows a fast and accurate graphical evaluation of the optimum design. It utilizes two closed form expressions for the upper and lower oscillation frequencies of the VCO. An expression of the tuning range is also derived. The effectiveness of the proposed design methodology has been tested by simulating several VCOs in an IBM 0.13 mum CMOS technology.
A photovoltaic system suitable for the battery pack charging of an electrically power assisted velocipede
2012
The paper describes the designing, sizing, realization and setting up of a complete system suitable for the management of an electrically power assisted velocipede using a photovoltaic module for the charging of the batteries. In the work an overview on the sustainable mobility needs and on the commercial electrically power assisted velocipedes is presented and the "Ecolapa" prototype, set up in the SDELab laboratory of Palermo University, is precisely described underlining the designing, implementation and setting up phases of the photovoltaic charging system settled up on the velocipede. Moreover tests oriented on the setting up of the whole system and validation tests on the prototype ar…
Numerical Analysis of Medium Scale PV Plants and Their Power-Flow Control System With a Simple Three Phase Inverter
2012
This paper presents a mathematical analysis of a medium scale Photovoltaic (PV) power generation system connected to the distribution network and of its control system, in which the conversion stage is unique thanks to the absence of a boost chopper. Boost choppers are usually used as actuator for maximum power point tracking (MPPT). The conducted analysis leads to the conclusion that the used inverter presents two degrees of freedom that can be easily exploited in a control system in which the inverter simultaneously realizes the interconnection to the grid and at the same time realizes the MPPT control. The structure of the control system is then presented, discussed and then validated by…
Identification and robust control of DC/DC converter Hammerstein model
2008
Abstract—This paper deals with model-based robust control of dc/dc power electronic converters. The converter is described by means of a Hammerstein model consisting of the nonlinear static characteristics of the converter and a linear time-invariant (LTI) uncertainmodel whose parameters depend on the actual duty-cycle operating range. This suggests that the controller be designed using robust control techniques. In view of applying robust control, identification of the earlier LTI models is performed by means of simulation experiments, carried out on a converter switching model implemented onMATLAB/SIMULINK environment. Internal model control (IMC) structure is employed for the controller …
Analysis of driving cycles effects on power supply requirements of a fuel cell powered light-weight electric vehicle
2015
In this paper, fuel cell powered lightweight vehicles are addressed. A MATLAB/Simulink simulation model including motor, electrical drive, the fuel cell and power electronics systems is implemented. The model is well suited to perform the driving cycle test, which reproduces the speed pattern of an electric vehicle through urban, rural or motorway routes. This paper aims at investigating the most suited driving cycle to design high performances hybrid power supply for electric vehicles in terms of cruising range, cost and size of the power supply equipment. For this purpose, a legislative and a real-world driving cycles are selected. Effects of driving cycles on the power system requirement…
A General Mathematical Model for non-Redundant Fault-Tolerant Inverters
2011
Industrial systems able to release trusted services is an integrated concept that resumes the attributes of availability, reliability, safety, integrity, and maintainability. In power electronics this can be aimed via the introduction of fault tolerant architectures. While In the past technical literature the mathematical modeling problem for non-redundant converters was fronted studying separately the cases of fault leg by leg, in this paper a general model able to include the three possible cases of leg faults with a unique set of equation is introduced and discussed. The same model allows to evaluate the DC Link transient and steady state evolution and also allows to develop with much ea…
A Technique for Power Supply Harmonic Impedance Estimation Using a Controlled Voltage Disturbance
2002
A method for power system impedance estimation is presented. The method employs a power converter to inject a voltage transient onto the supply system. As the technique employs controlled power electronic devices it may be used as a stand alone piece of a portable measurement equipment, or it may be embedded into the functions of an active shunt filter for improved harmonic control. The impedance is estimated through correlation of the measured voltage and current transients. Simulations and experimental results demonstrate the measurement technique is highly accurate and effective.
A local linear black-box identification technique for power converters modeling
2009
In this paper, a black-box modeling technique for power electronic converters, also used in automotive environment is presented. The aim of this work is to provide a simple yet versatile and powerful tool to schematize complex electric devices in vehicular appliances, in order to fulfill the electromagnetic compatibility already during the project stage. By using input and output measured data, a composite local linear state space model is built up. Radial basis functions are used as weights for the local systems. The proposed approach is validated and applied in modeling a DC/DC converter for DC motors, a pulse width modulation inverter and a controlled rectifier.
Experimental Test and Simulations on a Linear Generator-Based Prototype of a Wave Energy Conversion System Designed with a Reliability-Oriented Appro…
2017
In this paper, we propose a reliability-oriented design of a linear generator-based prototype of a wave energy conversion (WEC), useful for the production of hydrogen in a sheltered water area like Mediterranean Sea. The hydrogen production has been confirmed by a lot of experimental testing and simulations. The system design is aimed to enhance the robustness and reliability and is based on an analysis of the main WEC failures reported in literature. The results of this analysis led to some improvements that are applied to a WEC system prototype for hydrogen production and storage. The proposed WEC system includes the electrical linear generator, the power conversion system, and a sea-wate…
A modular approach in teaching thyristor rectifiers with equation-oriented softwares
2014
This article is devoted to some issues of teaching power electronics in university courses. In the modern education system the students are expected to be no longer subject of passive learning, but that, within a certain extent, they collaborate in their training interactively with the teacher to develop the applications and the topics of the studied framework. For this purpose, this article presents a modular approach for teaching module regarding three-phase thyristor rectifiers. A simulator based on the MATLAB equation solver has been developed by considering the detailed physical operation of such converters. In particular, the realized simulator takes various aspects into account, incl…