Search results for "Power electronic"
showing 10 items of 91 documents
A High-Efficiency, Low-Cost Solution for On-Board Power Converters
2012
Wide-input, low-voltage, and high-current applications are addressed. A single-ended isolated topology which improves the power efficiency, reduces both switching and conduction losses, and heavily lowers the system cost is presented. During each switching cycle, the transformer core reset is provided. The traditional tradeoff between the maximum allowable duty-cycle and the reset voltage is avoided and the off-voltage of active switches is clamped to the input voltage. Therefore, the system cost is heavily reduced and the converter is well suited for wide-input applications. Zero-voltage switching is achieved for active switches, and the power efficiency is greatly improved. In the output …
Characterization of clamp-on current transformers under nonsinusoidal conditions
2009
This paper reports the performance of clamp-on current transformers under nonsinusoidal conditions. A set of experimental measurements helped to determine the ratio and the phase errors under two conditions: 1) sinusoidal excitation with frequencies from 45 to 1000 Hz and 2) nonsinusoidal excitation using the fundamental frequency and one harmonic, with adjusted phase shift. It was found that ratio and phase errors are affected by the phase angle between the harmonic and the fundamental and the harmonic amplitude. The effects of conductor location in the current transformer's window and of the air-gap width were also investigated. It was concluded that harmonic phase and ratio errors measur…
An approach to the optimum design of the magnetic circuit of a PM linear electrical generator driven by stochastical forces
2006
Linear electrical generator has been recently studied for the exploitation of sea waves energy. In order to maximize the energy extraction, the stochastic features of the energy source must be included in the mathematical model of the system. A PM linear electrical generator has been designed and built. The design has been optimized by including in the mathematical model used for the optimization the following aspects: 1. the dynamic and stochastic features of the waves; 2. a dynamic model of the hydraulic conversion system; 3. a parametric circuit model of the magnetic circuit as well as of the electric windings; 4. a circuit model of the power electronics converter used to connect the gen…
Vircator Technologies Comparison and Novel Anode Analysis
2021
High Power Microwave (HPM) sources are widely used as signal sources in radar, jammer, and Counter Improvised Explosive Devices (CIED). Such devices usually are heavy and bulky, characteristics that are in conflict with the small weight and power (SWaP) approach so that it is practically impossible to mount such HPMs on several platforms with reduced spaces (e.g., avionic, UAVs). During the last century, several devices have been proposed, all of them heavy due to the components that they need such as the magnetic material of the Magnetron, Klystron, or Gyrotron. Considering the HPM sources for pulsed applications, the VIRtual CAThode oscillatOR (Vircator) represents the best candidate due …
Impact of RES penetration on the frequency dynamics of the 500 kV vietnamese power system
2019
The increase of renewable energy sources (RES) typically operating as converter-interfaced generation (CIG) is progressively causing a significant change of power systems operation paradigm. The reduction of the overall available kinetic energy and the consequent impact on the dynamic response of the system is a relevant issue currently under investigation in academic and industrial scopes. The work analyzes the impact of different CIG penetration in the three areas of the 500 kV Vietnamese power system, North, Center and South. The system is modified substituting conventional synchronous generation with converter-interfaced generation. The models of power converters and corresponding contr…
Design optimization for the quench protection of DTT's superconducting toroidal field magnets
2021
Abstract The paper is focused on the optimal design of Fast Discharge Unit (FDU) for the quench protection of the Toroidal Field (TF) magnets of the Divertor Tokamak Test facility (DTT), an experimental facility under construction in ENEA Frascati Research Centre (Rome, Italy). The FDU is a safety key component that protects the superconducting magnets when a quench is detected through the fast extraction of the energy stored in the magnets by adding a discharge dump resistor (DR) in the TF magnets circuit. A comparison between a fixed DR and a switched variable DR has been implemented by changing resistor parameters and by using multiple current control of the power electronics components …
High frequency modeling technique for three phase power electronics module
2015
Nowadays, the high integrated power electronics modules (PMs), characterized by high speed, low loss and hard ware miniaturization, represent a new technology that meets the emerging demands of many applications, such us vehicle and home appliance, renewable energy sources in smart grid. The integration process and the high switching speeds increase the PM electromagnetic emissions that can create electromagnetic interference (EMI) with electric/electronic devices near the PMs. For this reason, electromagnetic compatibility (EMC) have to be carefully considered, yet in the design phase, to guarantee the reliability of PM systems. In this paper a method to develop a high frequency (HF) model…
Partial Discharge Measurements under DC Voltages Containing Harmonics Produced by Power Electronic Devices
2018
Partial Discharge (PD) monitoring is one of the main diagnostic instrument to evaluate the reliability of modern electrical transmission and distribution systems. The widespread use of High voltage dc (HVDC) connections increase the demand of voltage source converters (VSCs) which, as a consequence, has brought about new challenges in the field of partial discharge measurements. In fact, the output voltage waveforms generated by AC/DC modular multilevel converters (MMCs) are affected by a significant harmonic content which influences the Partial Discharges (PDs) activity. For this reason, previous research mainly investigated the PD phenomenon on the AC side of the converter. The aim of the…
Quasi-static magnetoresistive sensor modeling for current-time conversion circuit applications
2011
In this paper we report a current-to-time converter (CTC) suitable for current sensor monitoring in low power applications. Based on a discrete resistence-to-frequency converter and a Giant MagnetoResistance (GMR) current sensor. Simulations have been done using a quasi-static electrical Verilog-A model for the GMR current sensor. A reduced set of parameters has been extracted to characterize the GMR sensor's behavior. The application has been analyzed making use of different sensors, whose device parameters were previously extracted. Finally, the accuracy of the models has been tested by comparing with experimental transient measurements.
A Test Circuit for GaN HEMTs Dynamic Ron Characterization in Power Electronics Applications
2019
Wide bandgap devices such as GaN HEMTs are a promising technology in the field of Power Electronics. Due to the physical properties of the Gallium nitride and the device design, they can outperform their Silicon counterparts for the design of highly efficient power switching converters. However, its design should face certain effects that can diminish its performance. One of such effect is the degradation mechanism known as dynamic onresistance (dynamic RON,), being its mitigation one of the main objectives in the design of the device. In this paper, a circuit is proposed for assessing if this effect is present in GaN transistors in power electronics applications. The circuit allows testing…