Search results for "Pressure drop"

Influence of the porosity profile and sets of Ergun constants on the main hydrodynamic parameters in the trickle-bed reactors

2014

Abstract The Eulerian multiphase code has been applied for the comparative simulation of the experimental results obtained for varying flow rates of both fluid phases and for systems of various physicochemical properties used in the laboratory trickle-bed reactor (TBR). Therefore six different radial porosity profiles and three sets of the Ergun constants used in the relations defining the interphase momentum exchange have been implemented into the CFD code. The mean relative error of the pressure drop and of the averaged holdup as well as the standard deviation determined with respect to the experiments have been used as the criterion for the validation of the theoretical model. These valu…

Characterization of a Modified Expansion Condensation Particle Counter for Detection of Nanometer-Sized Particles

2009

A newly developed condensation particle counter provides measurements of aerosol particle number densities for size diameters as low as 3 nm. This Expansion Condensation Particle Counter (ECPC) operates based on fast adiabatic expansion with specialized detection and evaluation of the temporal development of light scattered by the ensemble of growing droplets. In its new configuration the ECPC has been modified such that a previously needed calibration factor became obsolete. In this article the new design is described which now includes a fast pressure sensor for monitoring the pressure drop inside the measurement chamber. Extensive laboratory experiments for characterizing the ECPC are de…

Evaluation of positron-emission-tomography for visualisation of migration processes in geomaterials

2008

Abstract Positron-emission-tomography (PET) was applied for direct visualisation of solute transport in order to overcome the limitations of conventional methods for measuring advection and diffusion properties. At intervals from minutes to days the 3D-spatial distribution of the PET-tracer is determined. This spatiotemporal evolution of the tracer concentration can be used as experimental basis for clarification of the relevant transport processes, derivation of transport parameters, and model calibration. Here, 18 F and 124 I in 0.01 M carrier solution of KF and KI, respectively, have been chosen out of the limited number of available PET-tracers, primarily on account of their decay time …

On the hydraulic behaviour of ITER Shield Blocks #14 and #08. Computational analysis and comparison with experimental tests

2016

Abstract As a consequence of its position and functions, the ITER blanket system will be subjected to significant heat loads under nominal reference conditions. Therefore, the design of its cooling system is particularly demanding. Coolant water is distributed individually to the 440 blanket modules (BMs) through manifold piping, which makes it a highly parallelized system. The mass flow rate distribution is finely tuned to meet all operation constraints: adequate margin to burn out in the plasma facing components, even distribution of water flow among the so-called plasma-facing “fingers” of the Blanket First Wall panels, high enough water flow rate to avoid excessive water temperature in …

1989

Heat of crystallization significantly slows down polymer cooling and thus pressure drop increase during mould filling with thermoplastic crystalline polymers. If a correction of thermal diffusivity can account for such a cooling slow down at least as far as the effect on pressure drop is concerned, the use of nonisothermal crystallization kinetics may be avoided in the simulation of mould filling. A procedure to identify such a correction is outlined in this work. Pressure drop values during cavity filling calculated by using a corrected thermal diffusivity in the model proposed by Lord and Williams favourably compare with literature data taken with polypropylene and polyethylene resins. Be…

Two-phase flow of liquid–liquid mixture in the range of the water droplet pattern

2002

Abstract Phenomena accompanying flow of water–oil mixture during droplet flow of water in oil have been described. Aims used in the determination of characteristic parameters in two-phase liquid–liquid flow have been presented. The method for calculating the equivalent viscosity and pressure drop during flow of liquid–liquid mixture in the range of the water droplet pattern has been given.

CFD prediction of concentration polarization phenomena in spacer-filled channels for Reverse Electrodialysis

2014

Abstract Salinity Gradient Power generation through Reverse Electrodialysis (SGP-RE) is a promising technology to convert the chemical potential difference of a salinity gradient into electric energy. In SGP-RE systems, as in most membrane processes, concentration polarization phenomena may affect the theoretical driving force and thus the performance of the process. Operating conditions, including the feed solution flow rate and concentration and the channels׳ geometrical configuration, may greatly influence both the polarization effect and the pumping energy consumption. The present work uses CFD to investigate the dependence of concentration polarization and pressure drop on flow rate, f…

CFD Modelling of the Demister in the Multi Stage Flash Desalination plant

2011

Abstract Demisters are used to remove entrained brine droplets from flashed off vapor within the flashing stages of the multi stage flash desalination process (MSF). This is necessary to prevent accumulation of brine droplets on the outside surface of the condenser tubes and contamination of the desalinated water. The aim of this work is to design a new demister with lower pressure drop and unaffected separation efficiency which can be later installed in the flashing stages of the MSF plant and causes reduction in the required heat transfer area. In this work the demister performance is predicted as a function of design (wire diameter), and operating parameters (stage temperature). This obj…

Jet Engine Design Optimization Using a Knowledge-Based Master Model

2012

This paper presents a preliminary design optimization study of a jet engine structure using a knowledge-based master modeling approach. The objective function is derived based on input-output relationships of a cost-performance model, where specific fuel consumption, pressure loss and direct cost are considered. The advantage of this problem formulation is that it entails a single composite objective function that takes into account mass, structural characteristics, dynamic response and translates them to a direct operational cost function to be minimized. A fan-blade-off scenario is considered as the loading case in this paper. The loss of one fan blade during nominal operation causes a ro…

Steady state and transient thermal–hydraulic analyses on ITER divertor module

2005

Abstract One of the most challenging components of ITER is the divertor devoted at controlling the characteristics of the plasma boundary, exhausting the α particles and reducing the impurities in the plasma. The thermal–hydraulic design of the divertor is particularly, demanding because of the high heat loads and the cooling flow margin in the plasma-facing components (PFCs). The pressure drop is limited by the pumping power and also avoiding the risk of reaching critical heat flux (CHF). Furthermore, for maintenance operation foreseen, each single divertor cassette should be drained and dried before withdrawing it out from the vacuum vessel. To address these requirements, European Fusion …