Search results for "Pressure"
showing 10 items of 4493 documents
Assessment of conduit artery vasomotion using photoplethysmography
2013
Vasomotion is a spontaneous oscillation of vascular tone. The phenomenon has been observed in small arterioles and capillaries as well as in the large conduit arteries. The layer of smooth muscle cells that surrounds a blood vessel can spontaneously and periodically change its tension and thereby the arterial wall stiffness also changes. As the understanding of the phenomenon is still rather obscure, researchers would benefit from a low-cost and reliable investigation technique such as photoplethysmography (PPG). PPG is an optical blood pulsation measurement technique that can offer substantial information about the arterial stiffness. The aims of this pilot study were to evaluate the usefu…
Local structure analysis of the hard-disk fluid near melting
1997
The local structure of the hard-disk fluid is studied across its melting transition by means of Monte Carlo simulations and measurement of a local order parameter. Evidence for a linear behavior of this quantity in an intermediate density range is found, as well as indications for a possible ensemble difference between constant volume and constant pressure simulations within the presently accessible system sizes.
Cobalt ferrite nanoparticles under high pressure
2015
We report by the first time a high pressure X-ray diffraction and Raman spectroscopy study of cobalt ferrite (CoFe2O4) nanoparticles carried out at room temperature up to 17 GPa. In contrast with previous studies of nanoparticles, which proposed the transition pressure to be reduced from 20–27 GPa to 7.5–12.5 GPa (depending on particle size), we found that cobalt ferrite nanoparticles remain in the spinel structure up to the highest pressure covered by our experiments. In addition, we report the pressure dependence of the unit-cell parameter and Raman modes of the studied sample. We found that under quasi-hydrostatic conditions, the bulk modulus of the nanoparticles (B0 = 204 GPa) is consid…
7.22 Health Monitoring of High Performance Composite Pressure Vessels
2018
The most important form of damage in carbon fiber reinforced composite pressure vessels is the failure of the fibers however the rate of fiber failure is controlled by the viscoelastic nature of the matrix, which determines overall in-service lifetimes. This type of damage is very different from that encountered with metal pressure vessels and requires a detailed understanding in order to ensure reliability. Innovative proof testing methods based on these processes are necessary. The damage processes and the means of quantifying them are discussed. Their reliability under pressure over periods of decades is analyzed. Intrinsic safety factors linked directly to the properties of the composit…
Environmental chamber for an atomic force microscope.
2007
A commercial atomic force microscope (AFM), originally designed for operation in ambient conditions, was placed inside a compact aluminum chamber, which can be pumped down to high vacuum levels or filled with a desired gaseous atmosphere, including humidity, up to normal pressure. The design of this environmental AFM is such that minimal intrusion is made to the original setup, which can be restored easily. The performance inside the environmental chamber is similar to the original version.
Strength and strain capacities of concrete compression members reinforced with FRP
2003
The analytical compressive behavior of concrete members reinforced with fiber-reinforced polymer (FRP) was examined. The variation in the shape of the transverse cross-section was analyzed. The bearing capacity and the increase in the maximum strain for members having a cross-section which was circular, square or square with round corners reinforced with FRP were determined. The proposed analytical model allows one to evaluate the confining pressure in ultimate conditions considering the effective confined cross-section and also allows one to determine the ultimate strain corresponding to FRP failure through a simplified energetic approach. Analytical results are then compared to experiment…
Quantifiable analysis of the failure of advanced carbon fibre composite structures leading to improved safety factors
2022
Abstract The increasing use of advanced composite materials means that they must now be considered as major materials for a wide variety of structures some of which will be in service for decades. There is therefore an important need to be able to quantify damage accumulation leading to failure in these materials particularly as they are often used in extreme situations for which failure must be avoided. This review shows how damage accumulation in many major composite structures is dominated by fibre failure but that the viscoelastic nature of the matrix induces time effects including delayed failure. It is shown that damage accumulation can be quantitatively modelled using a multi-scale a…
Pressure sensor development based on Dielectric Electro Active Polymers
2012
The Dielectric Electro Active Polymer's (DEAP's) sensing capabilities is one of the main trio-characteristics of the material applicable area's, the trio-formations as applicable use are actuator, transducer and last but not least sensor. It is noted here that one of the main value propositions whenever DEAP material is used is the dual characteristics as the sensing/actuating capability.
Optical thermal filters for eXTP: manufacturing and characterization
2020
In order to ensure the effective detection of X-ray astronomical detectors by blocking ultraviolet, visible and infrared light, adding optical thermal filter in front of the load is an effective method. According to the scientific requirements of eXTP, optical thermal filters with aluminized polyimide (PI) film structure had been designed and tested in this paper, the results of mechanical tests including burst pressure, vibration and acoustic tests, also the transparent properties of optics in UV, Vis and IR lights are presented. The mechanical test results show that the filters for LAD and SFA can't pass the acoustic tests, causing the thickness of PI should be increased or a nickel mesh …
Fatigue behaviour of self-piercing riveting of aluminium blanks and carbon fibre composite panels
2012
In this article, the fatigue behaviour of self-piercing riveted joints in 2024-T6 aluminium sheets and carbon fibre composite panels is studied through experimental tests and numerical simulations. This study, aimed to evaluate the best process conditions and the mechanical behaviour of the joint itself, can be divided into few phases: the first one in which the static mechanical behaviour was investigated in order to evaluate the best process conditions (such as the best value of oil pressure of the riveting system) and the second one which had the purpose to determine the fatigue behaviour of the joint. Finally, a finite element method analysis of the riveting process was developed in or…