Search results for "Propylene"

Relationship between the residual and total strain from creep‐recovery tests of polypropylene/multiwall carbon nanotube composites

2020

Recycling of inside upholstery of end-of-life cars

2005

A model study for the recycling of the interior upholstery plastic parts of end-of-life cars has been carried out by reprocessing the homogenized scraps of an upholstery farm in the presence of different compatibilizer precursors, such as an ethylene-glycidylmethacrylate copolymer (EGMA), a maleic anhydride functionalized thermoplastic elastomer (SEBS-MA), etc. The investigated scraps contained recycled polyethylene (from agricultural uses) and poly(ethylene terephthalate), as the main components, plus minor proportions of polypropylene, polyamide-6, and other additives, including an ethylene copolymer (EC), probably an ethylene-acrylic acid copolymer, which is used to compatibilize the car…

A study of spalling behaviour of PAN fibre-reinforced concrete by thermal analysis

1993

Comparisons are made between polypropylene (PP) fibres and polyacrylonitrile (PAN) fibres in order to relate the thermal properties of fibres with the respective fibre mortar behaviour under thermal exposure. Thermogravimetry (TG), differential scanning calorimetry (DSC) and thermochromatography (ThGC) are utilized. When a cementitious fibre mortar is being heated, several physical phenomena occur in the temperature range between 100°C and 200°C. There is a significant difference in the thermal behaviour between PP and PAN fibres. PP fibres melt at 160–170°C. The non‐melting behaviour of PAN fibre together with its rapid exothermic degradation reactions at around 300°C may add risk to the s…

Influence of high power ultrasound on physical-chemical properties of polypropylene films aimed for food packaging: barrier and contact angle features

2017

Investigation was focused on the impact of high power ultrasound (HPUS), also called thermosonication, on the oxygen permeation properties (permeability, solubility and diffusion coefficients) of barrier films aimed for food packaging. For this purpose, biaxially oriented polypropylene (BOPP) coated with acrylic/polyvinylidene chloride (BOPPAcPVDC) and biaxially oriented coextruded polypropylene (BOPPcoex) were used. The physical–chemical profile of the samples was determined using goniometry. There is a significant impact only of extreme HPUS conditions (the longest time and the highest amplitude) on the permeability, solubility and diffusion coefficients of oxygen through the BOPP films. …

Characterization of blends of polypropylene with a semirigid liquid-crystal copolyester

1991

Abstract Blends with a liquid-crystal polymers (LCP) as one component show, in general, very interesting properties. Reduction of shear viscosity and improvement of mechanical properties are very remarkable. High melting temperatures and high costs of the LCP limit the use of these blends. A new class of thermotropic LCPs with flexible spaces, with relatively low melting temperatures, can overcome the first problem. In this work, rheological and mechanical properties of blends of polypropylene with low contents of this LCP are presented. Torque during extrusion and viscosity decrease with LCP content. Elastic modulus is remarkably increased when the LCP phase is oriented.

Mesophase formation in poly(propylene-ran-1-butene) by rapid cooling

2009

Abstract The effect of random insertion of low amount of 1-butene of less than about 11 mol% into the isotactic polypropylene chain on structure formation at non-isothermal crystallization at different rate of cooling was investigated by X-ray scattering, density measurements, and atomic force and polarizing optical microscopy. Emphasis is put on the evaluation of the condition of crystallization for replacement of lamellar crystals by mesomorphic nodules on increasing the cooling rate/supercooling. In the polypropylene homopolymer, mesophase formation occurs on cooling at rates larger about 150–200 K s −1 , while in case of poly(propylene- ran -1-butene) mesophase formation is observed on …

Reduction of the interfacial tension between ‘immiscible’ polymers: to which phase one should add a compatibilizer

2001

Abstract The reduction of interfacial tension σ between polyethylene oxide (PEO) and polypropylene oxide (PPO) by either a triblock copolymer EO–PO–EO or a diblock copolymer styrene–EO was studied by means of the pendant drop method from 70 to 120°C. Time independent data correspond to stationary states and do not represent equilibrium information. The addition of the compatibilizer to the PPO phase is approximately twice as efficient as the addition to the PEO phase for both block copolymers. Knowing the concentration dependence of σ for one of the coexisting phases it is possible to forecast the effects resulting from the addition of the other phase by means of model considerations based …

Time–temperature correspondence prediction of stress relaxation of polymeric materials from a minimum of data

2002

Abstract We have determined the stress relaxation of a longitudinal polymer liquid crystal (PLC), polypropylene and their blends containing 10 and 20% of the PLC at the constant strain of 0.5%. The results for nine temperature levels in the range between 20 and 100 °C were used to create master curves for T ref =20 ° C . The temperature shift factors aT were calculated using a general formula derived by one of us and based on free volume vf and the chain relaxation capability model. The predicted values agree with the experimental ones for all materials studied within limits of the experimental accuracy. Moreover, the relation between the shift factor aT and the reduced volume ṽ has been us…

Structure of isotactic polypropylene–hydrogenated oligo(cyclopentadiene) (iPP–HOCP) blends Part II. HOCP-rich blends

2000

Abstract Blends of isotactic polypropylene (iPP) and hydrogenated oligo(cyclopentadiene) (HOCP) were investigated to gain structural information by means of both SAXS and SANS techniques. The composition range (from 30 to 60% w/w HOCP content) and the temperature range (between 25 and 160°C) were chosen in order to cover the miscibility gap in the phase diagram of the material system. In a previous report, blends lying outside the miscibility gap have been investigated and the corresponding SAXS patterns were interpreted in terms of a pseudo-two phase model. For the SAXS patterns, blends lying inside the miscibility gap are rather hard to be interpreted in terms of such a model. On the othe…

Investigations of polymerizable multilayers as gas separation membranes

1985

Abstract Polymerizable Langmuir—Blodgett (LB) multilayers of several diacetylenic amphiphiles were investigated on gas-permeable, polymeric supports. Macroscopically homogeneous multilayer films of hexacosa-10,12-diynoic acid and pentacosa-10,12-diyne phosphonate could be built up on polypropylene and polytetrafluoroethylene materials. As shown by scanning electron microscopy, the microscopic homogeneity of the built-up multilayers was mainly controlled by the surface structure of the support material, whereas the chemical nature of the support and photopolymerization of the layers did not affect the high order of the films. Such LB multilayers deposited on porous support materials are able…