Search results for "Propylene"
showing 10 items of 285 documents
Morphology, reorganization and stability of mesomorphic nanocrystals in isotactic polypropylene
2006
Abstract The morphology and thermodynamic stability of crystals of isotactic polypropylene (iPP) were analyzed as a function of the path of crystallization by atomic force microscopy (AFM) and differential scanning calorimetry (DSC). Samples were melt-crystallized at different rates of cooling using a “controlled rapid cooling technique”, and subsequently annealed at elevated temperature. Mesomorphic equi-axed domains with a size less than 20 nm were obtained by fast cooling from the melt at a rate larger about 100 K s−1. These domains stabilize on heating by growing in chain direction and cross-chain direction, to reach a maximum size of about 40–50 nm at a temperature of 433 K, with the q…
Effects of natural fibres reinforcement in lime plasters (kenaf and sisal vs. Polypropylene)
2014
Nowadays the tendency to realize environment-friendly products is becoming more widespread to ensure sustainable and smart development. The synthetic fibres, frequently used, are harmful to the environment because they are non-degradable and non-renewable. Their use has resulted in an increase of oil consumption. Therefore, the possibility of replacing them with natural fibres becomes increasingly concrete confirmed by the researches and investigations carried out. In this work three lime based plasters were prepared and analysed to evaluate the influence on their performance of different fibres used as reinforcement. In particular each plaster was realised by adding to the mortar the same …
Effect of a Compatibilizer on the Morphology and Properties of Polypropylene/Polyethylentherephthalate Spun Fibers
2017
Fibers spun by melt spinning of binary and ternary polypropylene/ polyethylenetherephthalate blends have been produced and characterized in order to investigate the effect of a compatibilizer on their morphology and mechanical properties. The compatibilizer was a maleic anhydride-functionalized rubber copolymer. The effect of the compatibilizer was well evident in the isotropic state, as the morphology became very fine, the size of the dispersed particles was very small, and the adhesion was better. The effect of the compatibilizer on the mechanical properties is very relevant, especially in the elongation at break. On the contrary, no relevant effect was observed in the anisotropic oriente…
The poly(propylene oxide-co-ethylene oxide) gradient is controlled by the polymerization method: determination of reactivity ratios by direct compari…
2019
An investigation of the highly relevant copolymerization of ethylene oxide (EO) and propylene oxide (PO) by in situ1H NMR spectroscopy shows striking differences in the copolymerization kinetics, depending on the polymerization method. Examination of the EO/PO copolymerization kinetics using iBu3Al for the monomer-activated anionic ring opening polymerization (AROP) confirmed a strong monomer gradient of the microstructure (rEO = 6.4, rPO = 0.16) in contrast to the known weak gradient in the conventional AROP (rEO = 2.8, rPO = 0.25). The first study via in situ1H-NMR kinetics of the copolymerization of PO and EO under heterogeneous double metal cyanide (DMC) catalysis, a method that produce…
Effect of processing temperature and mixing time on the properties of PP/GnP nanocomposites
2020
Abstract During processing of molten polymers the thermal and mechanical stress acting on the melt in presence of oxygen can induce degradation with a modification of the chemical structure of the polymers. This picture can become even more relevant if the melt is a multiphasic polymer system. In this last case, the effects of the degradation depend also on the presence of a second phase and on the interactions between the two phases. In this work, the effect of the processing conditions, temperature and time, have been considered in order to investigate the thermo-mechanical and thermo-oxidative degradation of nanocomposites made by polypropylene and different contents of graphene nanoplat…
Effect of the additive level and of the processing temperature on the re-building of post consumer pipes from polyethylene blends
2007
Abstract One of the main shortcomings of the mechanical recycling is that the properties of the secondary materials are generally sensibly inferior with respect to the virgin ones. This feature implies, for sure, that they cannot be used for the same technological application but also other uses of the secondary material are impossible. The aim of this work is to study the re-building of recycled post-consumer pipes, made of a blend of different polyethylenes, by re-processing in the presence of a nitroxyl compound as radical generator. The processing temperature and the additive concentration have been varied in order to study the effect of these parameters on the final properties. The mec…
Investigation on the Properties and on the Photo-Oxidation Behaviour of Polypropylene/Fumed Silica Nanocomposites
2021
This work investigates the effects of very small amounts of fumed silica on the morphology and on the rheological and mechanical behaviour of polypropylene nanocomposites and on their photo-oxidation behaviour. Polypropylene nanocomposites were prepared using a twin-screw corotating extruder with 0, 1 and 2 wt/wt% of SiO2. Morphological, mechanical, thermomechanical and rheological properties were examined. It was found that the viscosity of the matrix is reduced by the presence of the silica nanoparticles, suggesting a poor adhesion between the two phases and probably some lubricating effect. On the contrary, the mechanical and, in particular, the thermomechanical properties of the matrix …
Accelerated weathering of PP based nanocomposites: Effect of the presence of maleic anhydryde grafted polypropylene
2013
Polymer nanocomposites are currently a topic of great interest. The increasing importance they are gaining also in the standpoint of industrial applications, is giving concerns regarding their environmental stability and, in general, their behaviour in outdoor applications, under direct solar irradiation. Papers available in the literature have highlighted the different influences of different nanosized fillers, in particular clay-based nanofillers; however, few data are available regarding other nanosized fillers. Furthermore, the research on polymer nanocomposites has clearly pointed out that the use of compatibilizers is required to improve the mechanical performance and the dispersion o…
Photo-oxidation of polypropylene/graphene nanoplatelets composites
2019
Abstract The photo-oxidation behaviour of polymer nanocomposites depends not only on the photo-oxidation behaviour of the matrix, but also on the chemical composition, on the physical properties of the nanoparticles and on the possible interactions between the two phases. In the case of nanocomposites with carbonaceous particles, the main effect is a photo-stabilization due to the absorption of the UV energy and the radical scavenging action. In this work we investigated the effect of the presence of graphene nanoplatelets on the photo-oxidation behaviour of the polypropylene. The presence of the graphene nanoplatelets improves the photo-resistance of the polypropylene and this effect incre…
Thioether-Bearing Hyperbranched Polyether Polyols with Methionine-Like Side-Chains: A Versatile Platform for Orthogonal Functionalization
2016
The synthesis of thioether-bearing hyperbranched polyether polyols based on an AB/AB2 type copolymerization (cyclic latent monomers) is introduced. The polymers are prepared by anionic ring-opening multibranching copolymerization of glycidol and 2-(methylthio)ethyl glycidyl ether (MTEGE), which is conveniently accessible in a single etherification step. Slow monomer addition provides control over molecular weights. Moderate dispersities (Đ = 1.48–1.85) are obtained, given the hyperbranched structure. In situ 1H NMR copolymerization kinetics reveal reactivity ratios of rG = 3.7 and rMTEGE = 0.27. Using slow monomer addition, copolymer composition can be systematically varied, allowing for th…