Search results for "RELIABILITY"
showing 10 items of 1563 documents
The efficient mixed matrix antifouling membrane for surfactant stabilized oil-in-water nanoemulsion separation
2019
Abstract Membrane technology has raised considerable interest in sustainable water purification over the past decade. The development of antifouling membranes is always the basic approach to address the omnipresent bottlenecks of the membrane fouling. In this study, AlSi2O6 nanoparticles were synthesized using a coprecipitation technique and their influence was investigated on the permeation and antifouling properties of ultrafiltration (UF) membranes of polysulfone (PSF). A series of membranes were fabricated with various concentrations (such as 0.0, 2.5, 5 and 7.5 wt%) of AlSi2O6 nanoparticles through diffusion induced phase separation method. The prepared composite membranes demonstrate …
Laboratory Tests for Assessing the Reliability and Durability of Innovative Cold-Glued 3D Glass Building Subcomponents
2020
The paper shows the results of analyses of the behavior of an innovative subcomponent made of two glass shells and a plastic thermal belt interfaced with a resin-based adhesive, in order to define the plastic material–adhesive combination able to guarantee compliance with the requirements related to mechanical strength, thermoacoustic insulation, dimensional stability, material compatibility, and durability. Two different types of ultraviolet (UV)-curing adhesive were used to establish the best plastic–adhesive combination. A study of the mechanical behavior and the reliability over time of the bonded assembly was conducted by performing accelerated weathering tests and tensile tests on 30 …
On the hydro-mechanical behaviour of a lime-treated embankment during wetting and drying cycles
2018
Abstract The paper presents some experimental results obtained on samples extracted from a full-scale embankment obtained by compacting a lime-treated clayey soil. A comprehensive test programme was carried out in order to highlight the improvement of mechanical behaviour induced by lime treatment as well as to assess the durability of the improved material, which may be affected by severe seasonal wetting and drying cycles. Direct shear tests, triaxial compression tests, swelling potential measurement and oedometric tests were performed on samples cured in controlled environmental conditions for at least 18 months. Wetting and drying cycles were applied in a very wide range of suction valu…
7.22 Health Monitoring of High Performance Composite Pressure Vessels
2018
The most important form of damage in carbon fiber reinforced composite pressure vessels is the failure of the fibers however the rate of fiber failure is controlled by the viscoelastic nature of the matrix, which determines overall in-service lifetimes. This type of damage is very different from that encountered with metal pressure vessels and requires a detailed understanding in order to ensure reliability. Innovative proof testing methods based on these processes are necessary. The damage processes and the means of quantifying them are discussed. Their reliability under pressure over periods of decades is analyzed. Intrinsic safety factors linked directly to the properties of the composit…
Nanocrystal memories for FLASH device applications
2004
Nanocrystals memory cells, in which the conventional polysilicon floating gate is replaced by an array of silicon nanocrystals, have been fabricated and characterized. Single cells and cell arrays of 1 Mb and 10 k have been realized by using a conventional 0.15 μm FLASH technology. Si nanocrystals are deposited on top of tunnel oxide by chemical vapor deposition. Properties of the memory cell have been investigated both for NAND and NOR applications in terms of program/erase window and programming times. Suitable program/erase threshold voltage window can be achieved with fast voltage pulses by adequate choice of tunnel and control dielectric. The feasibility of dual bit storage is also pro…
Diode laser reliability in dynamic laser speckle application: Stability and signal to noise ratio
2018
Abstract The biospeckle, or dynamic laser speckle, is used as a potential tool to monitor activity in many biological and non-biological materials from agriculture to medicine, and it is usually based on the use of He-Ne and diode lasers, the latter of which has great potential to be embedded in portable equipment. Some queries about the stability of the diode laser were raised, such as the real influence of the mode hopping phenomenon as a drawback in solid-state devices in comparison to the well-known He-Ne lasers, and thus we decided to test it . In addition, we present an alternative way to enhance the stability and the signal-to-noise ratio of the information using a relative index rat…
High Temperature SiC Blocking Diodes for Solar Array
2009
This paper presents the results of an experimental investigation of the performance of 300V-5A Silicon Carbide Ni and W Schottky diode operating in the range between -170°C to 270°C. We have developed these diodes as blocking diodes, for solar cell array protection in order to fulfill the BepiColombo mission specifications. An electro-thermal characterization has been performed taking into account the harsh condition of the mission (high temperature range and electrical stress). The destructive and non-destructive tests have assured that the designed SiC diodes are able to support the electro-thermal limits. A reliability test has also been performed to investigate the stability of forward …
Experimental evaluation of the durability of innovative cementitious coatings: photocatalytic activity and colour
2012
Today, in a world context characterized by high pollution levels and increasingly limited natural resources, even in the building sector, focusing on environmental issues, through energy saving and a more rational use of these resources, both during construction and management, is fundamental. An important contribution in this direction is given by the knowledge of the durability of products and building components, especially when innovative products are applied and no information are available on the reliability and service life. The research concerns the evaluation of the durability of cement-based photocatalytic coatings ("rasanti" in the Italian diction), containing different types of …
Estimation of the effective diffusivity of blowing agents in closed-cell low-density polyurethane foams based on thermal aging data
2021
Abstract Low-density closed-cell polyurethane (PU) foams are applied as thermal insulation materials due to their low thermal conductivity imparted by that of the physical blowing agent (PBA) used in foam production. However, foam conductivity tends to gradually increase with time, primarily due to changes in the gas composition in foam cells brought about by gas diffusion. To enable predicting the variation of conductivity during the service life of foam insulation, gas diffusivities are usually determined by measuring the gas composition in foams at different aging times. This study considers an alternative approach of estimating the effective diffusivities of gases in PU foams, which is …
CNT-based RFID passive gas sensor
2011
Summary form only given, as follows. Single-wall carbon nanotube (CNT) is examined for the design of a passive and maintenance-free wireless RFID sensor. CNT buckypaper is characterized from a dielectric and a sensitivity point of view, using an indirect way, by using antenna measurement and simulations in a controlled medium. A CNT-based prototype RFID tag is then described as the featured maintenance free sensor and experimentally verified for its applicability and sensitivity towards NH3.