Search results for "SAF"
showing 10 items of 2183 documents
Incorporation of nisin in poly (ethylene-co-vinyl acetate) films by melt processing: a study on the antimicrobial properties
2011
Both industry and academia have shown a growing interest in materials with antimicrobial properties suitable for food packaging applications. In this study, we prepared and characterized thin films of ethylene-co-vinyl acetate (EVA) copolymer with antimicrobial properties. The films were prepared with a film blowing process by incorporating a nisin preparation as an antimicrobial agent in the melt. Two grades of EVA containing 14 and 28% (wt/wt) vinyl acetate (EVA 14 and EVA 28, respectively) and two commercial formulations of nisin with different nominal activities were used. The effect of the nisin concentration also was evaluated. The films with the highest antimicrobial activity were th…
A Monte Carlo study of intersource effects in dome-type applicators loaded with LDR Cs-137 sources
2005
In this study, the dose rate distributions produced by low dose rate Cs-137 sources loaded in afterloadable dome applicators are studied using the Monte Carlo method. Dose differences between Monte Carlo results and calculations done using the superposition principle are within 1-3% in front of the applicator and between 3 and 10% near and along the longitudinal source axis. Consequently, the real doses to lateral vaginal wall, rectum and bladder are very close to the doses estimated applying the superposition principle, while the dose to the vaginal cuff has been overestimated by up to 10%.
Analysis of Fractional Viscoelastic Material With Mechanical Parameters Dependent on Random Temperature
2017
It is well known that mechanical parameters of polymeric materials, e.g., epoxy resin, are strongly influenced by the temperature. On the other hand, in many applications, the temperature is not known exactly during the design process and this introduces uncertainties in the prevision of the behavior also when the stresses are deterministic. For this reason, in this paper, the mechanical behavior of an epoxy resin is characterized by means of a fractional viscoelastic model at different temperatures; then, a simple method to characterize the response of the fractional viscoelastic material at different temperatures modeled as a random variable with assigned probability density function (PDF…
Safety analysis of the DONES primary heat removal system
2020
Abstract The development of a neutron source able to reproduce the irradiation conditions typical of a nuclear fusion reactor, in order to test candidate structural materials, is the main goal of the Work Package Early Neutron Source (WPENS) of the EUROfusion action. This source, named Demo Oriented NEutron Source (DONES), is a facility where neutrons are produced by means of D-Li interactions. More in detail, a beam of 125 mA deuterium ions at the energy of 40 MeV strikes a lithium jet flowing in a purposely shaped channel in order to obtain an intense and stable neutron flux for the irradiation of material samples. In the framework of these activities, safety analyses are a key aspect in …
An EPR method for discriminating radiation beams in ammonium tartrate and tooth enamel
2008
The radiation linear energy transfer (LET), which is the energy released by ionizing radiation per path unit, arouses great scientific interest because the biological damage produced by ionizing radiation in tissues is strictly related to LET. Radiation beams with different LETs will cause different spatial energy distribution and therefore different effects inside matter. In the last twenty years the EPR spectroscopy has become a valuable dosimetric tool. This technique allows absorbed dose measurements through the detection of free radicals produced by ionizing radiation in organic and/or inorganic compounds. In this work we have analyzed the possibility of using the acquisition of two co…
Intrinsic mechanisms limiting the use of carbon fiber composite pressure vessels
2016
International audience; The viscoelastic properties of the resins used in carbon fiber composite pressure vessels introduce time effects which allow damage processes to develop during use under load. A detailed understanding of these processes has been achieved through both experimental and theoretical studies on flat unidirectional specimens and with comparisons with the behavior of pressure vessels. Under steady pressures, the relaxation of the resin in the vicinity of earlier fiber breaks gradually increases the sustained stress in neighboring intact fibers and some eventually break. The rate of fiber failure has been modeled based only on physical criteria and shown to accurately predic…
Heavy-ion induced single event effects and latent damages in SiC power MOSFETs
2022
The advantages of silicon carbide (SiC) power MOSFETs make this technology attractive for space, avionics and high-energy accelerator applications. However, the current commercial technologies are still susceptible to Single Event Effects (SEEs) and latent damages induced by the radiation environment. Two types of latent damage were experimentally observed in commercial SiC power MOSFETs exposed to heavy-ions. One is observed at bias voltages just below the degradation onset and it involves the gate oxide. The other damage type is observed at bias voltages below the Single Event Burnout (SEB) limit, and it is attributed to alterations of the SiC crystal-lattice. Focused ion beam (FIB) and s…
LRPH device optimization for axial and shear stresses
2020
The paper concerns an in-depth study of a special connection for steel structures and the formulation of the related optimal design problem. The connection is called Limited Resistance Rigid Perfectly Plastic Hinge (LRPH) and it represents an innovative device devoted to join steel beam elements of frame structures. The device consists in a sequence of steel cross sections constituted by two parallel flanges with suitably different thickness connected by as many webs with constant and equal thickness. The fundamental innovation of the device is the possibility of designing special connections with elastic stiffness and limit strength independent of each other. Such a special characteristic …
The efficient mixed matrix antifouling membrane for surfactant stabilized oil-in-water nanoemulsion separation
2019
Abstract Membrane technology has raised considerable interest in sustainable water purification over the past decade. The development of antifouling membranes is always the basic approach to address the omnipresent bottlenecks of the membrane fouling. In this study, AlSi2O6 nanoparticles were synthesized using a coprecipitation technique and their influence was investigated on the permeation and antifouling properties of ultrafiltration (UF) membranes of polysulfone (PSF). A series of membranes were fabricated with various concentrations (such as 0.0, 2.5, 5 and 7.5 wt%) of AlSi2O6 nanoparticles through diffusion induced phase separation method. The prepared composite membranes demonstrate …
On the hydro-mechanical behaviour of a lime-treated embankment during wetting and drying cycles
2018
Abstract The paper presents some experimental results obtained on samples extracted from a full-scale embankment obtained by compacting a lime-treated clayey soil. A comprehensive test programme was carried out in order to highlight the improvement of mechanical behaviour induced by lime treatment as well as to assess the durability of the improved material, which may be affected by severe seasonal wetting and drying cycles. Direct shear tests, triaxial compression tests, swelling potential measurement and oedometric tests were performed on samples cured in controlled environmental conditions for at least 18 months. Wetting and drying cycles were applied in a very wide range of suction valu…