Search results for "SCOPE"

Microscopic defects and impurity analyses of multicrystalline silicon solar cells from different manufacturing routes

2013

It is important to fully understand the physical behavior of solar cells made by materials from alternative process routes. Solar cells from Elkem Solar Grade Silicon and standard polysilicon have been investigated with light beam induced current and electroluminescence imaging. The low efficiency regions have been further analyzed by Scanning Electron Microscopy under different imaging modes. It was found that cell regions of low performance had undergone plastic deformations resulting in the creation of crystalline defects appearing as subgrain patterns. Similar patterns were observed in both ESS™ and standard polysilicon. Energy-dispersive X-ray spectroscopy (EDS) and electron backscatte…

Quantitative molecular plating of large-area 242Pu targets with improved layer properties

2015

Abstract For measurements of the neutron-induced fission cross section of 242Pu, large-area (42 cm2) 242Pu targets were prepared on Ti-coated Si wafers by means of constant current density molecular plating. Radiochemical separations were performed prior to the platings. Quantitative deposition yields (>95%) were determined for all targets by means of alpha-particle spectroscopy. Layer densities in the range of 100–150 μg/cm2 were obtained. The homogeneity of the targets was studied by radiographic imaging. A comparative study between the quality of the layers produced on the Ti-coated Si wafers and the quality of layers grown on normal Ti foils was carried out by applying scanning electron…

Design and optimization of the wide-field spectrometer for EDGE mission

2007

The LOFT mission concept: a status update

2016

The Large Observatory For x-ray Timing (LOFT) is a mission concept which was proposed to ESA as M3 and M4 candidate in the framework of the Cosmic Vision 2015-2025 program. Thanks to the unprecedented combination of effective area and spectral resolution of its main instrument and the uniquely large field of view of its wide field monitor, LOFT will be able to study the behaviour of matter in extreme conditions such as the strong gravitational field in the innermost regions close to black holes and neutron stars and the supra-nuclear densities in the interiors of neutron stars. The science payload is based on a Large Area Detector (LAD, >8m2 effective area, 2-30 keV, 240 eV spectral resolut…

IBIS: The Imager on-board INTEGRAL

2003

The IBIS telescope is the high angular resolution gamma-ray imager on-board the INTEGRAL Observatory, successfully launched from Baikonur (Kazakhstan) the 17th of October 2002. This medium size ESA project, planned for a 2 year mission with possible extension to 5, is devoted to the observation of the gamma-ray sky in the energy range from 3 keV to 10 MeV (Winkler 2001). The IBIS imaging system is based on two independent solid state detector arrays optimised for low ( 15-1000 keV) and high ( 0.175-10.0 MeV) energies surrounded by an active VETO System. This high efficiency shield is essential to minimise the background induced by high energy particles in the highly excentric out of van All…

First observations of the X-ray transient EXO 2030+375 with IBIS/ISGRI

2003

We present a first INTEGRAL observation of the 42s transient X-ray pulsar EXO 2030+375 with IBIS/ISGRI. The source was detected during Cyg X-1 observations in December 2002. We analyzed observations during the outburst period from 9 to 21 December 2002 with a total exposure time of ~770 kiloseconds. EXO 2030+375 was almost always detected during single ~30 minute exposures in the 18-45 energy bands. The source light curve shows the characteristic outburst shape observed in this source.

Mechanical characterization of TiO2 nanofibers produced by different electrospinning techniques

2015

Abstract In this work TiO2 nanofibers produced by needle and needleless electrospinning processes from the same precursor were characterized and compared using Raman spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and in situ SEM nanomechanical testing. Phase composition, morphology, Young's modulus and bending strength values were found. Weibull statistics was used to evaluate and compare uniformity of mechanical properties of nanofibers produced by two different methods. It is shown that both methods yield nanofibers with very similar properties.

Study on the initial stages of water corrosion of fluorozirconate glasses

2004

Abstract The surface corrosion process associated with the hydrolysis of fluorozirconate glass, ZBLAN (53ZrF 4 , 20BaF 2 , 20NaF, 4LaF 2 , 3AlF 3 ) was investigated using X-ray photoelectron spectroscopy (XPS), grazing-incidence small angle X-ray scattering (GISAXS), X-ray reflectivity (XRR) and scanning electron microscopy (SEM). After a short exposure period (25 min) of the glass surface to deionized water the XPS data indicate an increase of the oxygen content accompanied by a decrease of fluorine concentration. The analysis of the chemical bonding structure identified the predominant surface reaction products as zirconium hydroxyfluoride and oxyfluoride species. The second most abundant…

LFZ growth of (Bi, Pb)–Sr–Ca–Cu–O superconducting fibers

1991

Powder x-ray diffraction, d.c. and a.c. susceptibilities, and SEM have been used to study (Bi1−xPbx)2Sr2Ca2Cu3O10−δ fibers grown by the Laser Floating Zone method. The well-oriented, long-grained superconductor fiber properties are shown to be highly dependent on the partial pressure of oxygen in the growth atmosphere, as well as on fiber pulling rate. Slowly grown fibers contain initially the 2212 (80 K) phase; the 2223 (110 K) phase also appears upon annealing in air. Faster growth rates result in fibers that contain a mixture of the 2212 and 2201 phases and, in this case, long annealing procedures are necessary to observe the 2223 phase.

Roughness evaluation of vine leaf by image processing

2013

International audience; The study of leaf surface roughness is very important in the domain of precision spraying. It is one of the parameters that allow to reduce costs and losses of phytosanitary prod- ucts and to improve the spray accuracy. Moreover, the leaf roughness is related to adhesion mechanisms of liquid on a surface. It can be used to define leaf nature surface (hy- drophilic/hydrophobic). The main goal of this study is thus to estimate and to follow the evolution of leaf roughness using image processing and computer vision. The develop- ment and application of computer vision for measurement of surface leaf roughness using artificial neural networks will be described. The syste…