Search results for "STABILITY"
showing 10 items of 3085 documents
A new high accuracy software based resolver-to-digital converter
2004
Tracking resolver-to-digital conversion (R/D converter or simply RDC) has emerged as one of the most robust method for obtaining high resolution position and angular speed information from resolvers. In this paper a low cost software based RDC is presented. The main features are: high accuracy, simple set up, high reliability and stability and good performances. Some experimental results, showing the capabilities of the proposed system, are presented and discussed. An output signal comparison between the proposed RDC and a commercial encoder is also presented.
Researches Regarding the Use of Elctrohydraulic Servosystems at Industrial Robots
2012
This paper presents some researches regarding the use of electro-hydraulic servo-systems in driving the industrial robots, taking into consideration the conditions in which the robots work. The researches conducted upon a particular system, reveal the optimum design elements for obtaining a good behaviour in use, subsequently a good stability in use.
Effects of electrical and mechanical parameters on the transient voltage stability of a fixed speed wind turbine
2011
Abstract In this paper the dynamic behaviour of a wind turbine connected to the grid is examined. The model of the fixed speed wind turbine has been developed with the Simulink simulation tool (Matlab Inc.) It is composed of the induction generator, the shaft system, an aerodynamic model of the wind turbine rotor and the pitch control system. Using this model, a three-phase fault is applied close to the wind turbine and cleared by disconnecting the faulty line. The rigorous implementation of the simulink model allowed the authors to evaluate the exact dependence of various electrical parameters for the induction generator on voltage stability. Furthermore, the effects of wind turbine mechan…
Effect of FRP Wraps on the Compressive Behaviour of Slender Masonry Columns
2017
In the last decade, Fibre Reinforced Polymer (FRP) wrapping technique has become a common method to retrofit masonry piers or columns with poor structural performances. The passive confinement effect induced by the external wrap allows increasing the compressive strength and ductility of the member. Several studies highlighted as the efficacy of this technique is affected by several key parameters, including the shape of the transverse cross section, stress intensification at the strength corner of sharp sections, amount and mechanical properties of adopted composite. Despite this technique has been widely studied from both theoretical and experimental point of view, most of studies focused…
A Simple Method to Assess Loadability of Radial Distribution Networks
2005
This paper proposes a simple method to asses loadability in radial distribution systems. The relevant problem of voltage stability has been dealt with in past times with reference to higher voltage systems for generation and transmission. In more recent papers, the problem has been considered also at distribution level, since the new electrical energy market requirements and the increasing loadings are now more and more influencing these systems. The proposed method is based on a static approach and proceeds by first evaluating the stability indices and then the different loadability factors (related to real, reactive and apparent power). These calculations are carried out by identifying, s…
Stability analysis of clay brick masonry columns: numerical aspects and modelling strategies
2014
Stability analysis of masonry piers and columns is one of the most frequently treated subjects in the field of structural engineering. This attention is probably due to the challenge to solving the problem including different effects, which play an important role in evaluating the response of eccentrically-loaded columns. In this connection, accurate stability analysis of masonry piers and columns has to take into account the non-linear stress–strain law of masonry in compression, the limited tensile strength, the induced slenderness due to crack formation and geometrical non-linearity. Different theoretical models and numerical approaches were developed in the past to analyze the combined …
Stability analysis of rotor whirl under nonlinear internal friction by a general averaging approach
2016
The two main sources of internal friction in a rotor-shaft system are the shaft structural hysteresis and the possible shrink-fit release of the assembly. The internal friction tends to destabilize the over-critical rotor running, but a remedy against this effect may be provided by a proper combination of some external damping in the supports and an anisotropic arrangement of the support stiffness, or at most by the support damping alone, depending on the system geometry. The present analysis reported here considers a general asymmetric rotor-shaft system, where the rotor is perfectly rigid and is constrained by viscous–flexible supports having different stiffnesses on two orthogonal plane…
On the sway stability improvement of car–caravan systems by articulated connections
2015
The present analysis is addressed to some promising connection arrangements between the towing vehicles and the towed trailers, where the two units are linked by four-bar isosceles trapeziums in place of the conventional pintle hitch. Two types of instability, of the divergent type or the oscillating type, may be analysed by the Routh–Hurwitz criterion or by the direct analysis of the characteristic equation. The constant term of this equation vanishes at the divergent instability threshold (zero of a real root), whereas the equation splits into two lower degree algebraic ‘sub-equations’ when the oscillating instability arises (pair of pure imaginary roots). A large field of geometrical con…
A pedagogical flight simulator for longitudinal airplane flight
2009
This article presents a bi-dimensional model of flight and describes the implementation of a flight simulator able to describe the different phases of longitudinal flight of a real airplane. After identifying the relevant physical variables, the equations of motion are written and solved using a numerical integration method. Using computer simulations, flight paths and time evolution of the kinematics variables are analyzed for a complete flight of a light commercial airplane. The simulations take into account and reproduce the basic actions of a pilot to control the flight. The main maneuvers involved in pilotage are also predicted and explained in terms of model parameter variations induc…
Impedance estimation of FEA's grid in fiji islands by V-I measurement by using the synchronous reference frame-PLL
2017
In recent years there has been a significant increase in distributed renewable energy generation feeding into the grid, with resulting detriment of the stability of the network, since present networks have not been designed for this purpose. To feed-in these renewable energy sources with minimum impact, it is essential to know a few grid parameters (voltage, current, grid impedance) at the point in which power supply is convenient. For this purpose in this paper an algorithm is proposed to obtain the estimated network impedance. This algorithm operates in time domain by a synchronous reference coordinate transformation, it requires only the measurement of the phase voltage with no-load and …