Search results for "STAINLESS-STEEL"
showing 6 items of 6 documents
Optical modeling of nickel-base alloys oxidized in pressurized water reactor
2012
International audience; The knowledge of the aging process involved in the primary water of pressurized water reactor entails investigating a mixed growth mechanism in the corrosion of nickel-base alloys. A mixed growth induces an anionic inner oxide and a cationic diffusion parallel to a dissolution-precipitation process forms the outer zone. The in situ monitoring of the oxidation kinetics requires the modeling of the oxide layer stratification with the full knowledge of the optical constants related to each component. Here, we report the dielectric constants of the alloys 600 and 690 measured by spectroscopic ellipsometry and fitted to a Drude-Lorentz model. A robust optical stratificati…
Influence of residual stress, surface roughness and crystallographic texture induced by machining on the corrosion behaviour of copper in salt-fog at…
2012
International audience; The influence of quadratic stress, crystallographic texture, lubrication and surface roughness generated by superfinish turning on the corrosion behaviour of pure copper was quantified in salt-fog atmosphere. This was done using statistical analysis (Pearson's correlation matrix). Three compounds were found after corrosion tests: atacamite/paratacamite and a black layer (mixture of the lubricant and the salt atmosphere). Surface characteristics were classified according to their decreasing influence on the formation of atacamite/paratacamite as follows: surface roughness and quadratic stress. Lubrication and the crystallographic texture have the lowest influence on c…
Multiscale modeling of polycrystalline materials: A boundary element approach to material degradation and fracture
2015
Abstract In this work, a two-scale approach to degradation and failure in polycrystalline materials is proposed. The formulation involves the engineering component level (macro-scale) and the material grain level (micro-scale). The macro-continuum is modeled using a three-dimensional boundary element formulation in which the presence of damage is formulated through an initial stress approach to account for the local softening in the neighborhood of points experiencing degradation at the micro-scale. The microscopic degradation is explicitly modeled by associating Representative Volume Elements (RVEs) to relevant points of the macro continuum, for representing the polycrystalline microstruct…
Laser densification of organic coating: Effects of laser wavelength, operating parameters and substrate properties
2012
International audience; Mechanical bonding and interface behaviour play a key role for any materials deposited on different substrates. Usually, a post-spray heat treatment is required to improve the coating morphology and to enhance mechanical properties of thermal-sprayed polymeric coating. The effects of YAG, CO2 and diode laser radiations on as-sprayed PEEK coating deposited on stainless steel and aluminum substrates were investigated. The results revealed a good coating densification and interface behavior. A correlation between coating and substrate absorption coefficients, their thermophysical properties and laser operating parameters was shown. Besides, the finite element modeling b…
Effect of temperature on the passive state of Alloy 31 in a LiBr solution: Passivation and Mott-Schottky analysis
2015
The passive behaviour of Alloy 31, a highly-alloyed austenitic stainless steel (UNS N08031), has been investigated in a LiBr heavy brine (700 g/l) at different temperatures using potentiostatic polarisation and Mott-Schottky analysis. Cation vacancies have been found to be the dominant defect in the passive films formed on Alloy 31. An increase in temperature enhanced the generation of cation vacancies at the film/solution interface and raised the steady-state passive current density. The density of defects within the passive film also increased significantly with temperature, making the film more conductive and less protective against localised attacks.
Passive Behavior and Passivity Breakdown of AISI 304 in LiBr Solutions through Scanning Electrochemical Microscopy
2014
The passive behavior and passivity breakdown of AISI 304 stainless steel in LiBr solutions has been investigated by means of scanning electrochemical microscopy (SECM). The sample generation - tip collection (SG-TC) mode was used to operate the SECM and the tip potential was biased to detect the electroactive species. The evolution of the current at the ultramicroelectrode tip with the applied potential within the passive range was followed at different LiBr concentrations. Results show that the absolute value of the current at the tip increases with the applied potential. Additionally, SECM was also used to detect stable pits formed on the stainless steel surface in a 0.2 M LiBr solution. …