Search results for "STING"

Integration of a structural features-based preclassifier and a man-machine interactive classifier for a fast multi-stroke character recognition

2003

A transputer-based parallel machine for handwritten character recognition is proposed. An algorithm based on structural features and on a tree classifier was used to accomplish the pre-classification of the unknown sample in order to speed up the recognition process. The algorithm for the final classification is based on the description of the strokes through Fourier descriptors. The learning phase is accomplished through a man-machine interactive process. The proposed system can expand its knowledge base. A special representation of this knowledge base is proposed in order to record a great amount of data in a suitable way. A fast multistroke handwritten isolated character recognition syst…

Development of “Design of Experiments” for modelling direct expansion air-conditioning systems under variable cooling loads and faulty operating cond…

2019

Air conditioning systems are widely adopted in the building sector and are generally responsible for high energy consumption. Part of this consumption is related to the poor maintenance adopted by plant owner over time, which causes energy performance degradation. Typical faults, such as fouling or improper refrigerant charge have been shown to heavily impact on energy consumption of these systems. In order to support cost-effective maintenance schedule, Fault Detection and Diagnosis Technique are under investigation in the world. However, in order to devise a diagnostic method a preliminary modelling of air conditioning system is due. To this aim, a test procedure which requires the least …

Life cycle energy sustainability assessment: an expanded framework for energy technologies

2018

Life Cycle sustainability assessment is one of the most relevant tools delving in sustainability science, based currently on the triple bottom line idea, that is identified in the use of the three tools of Life Cycle Assessment (LCA), Life Cycle Costing (LCC) and Social Life Cycle Assessment (S-LCA). The methodology is structured on international regulations and is currently being applied to a wide set of products and systems. However, when targeting specifically energy technologies with this methodology some specific issues need to be taken in consideration before applying tout court the standard LCSA methodology. Energy systems – in particular those where fluid streams are used – have an …

The economic and environmental sustainability in the choice of materials to improve the performances of existing buildings

2015

The concept of sustainability in the construction industry cannot, above all in this historical moment, include in its parameters considerations about economic, social and environmental factors. All this factors are deeply connected with the context, both for climatic reasons and for economic and social reasons. Technical valuations about the choice and use of materials must be motivated by reality in which we work, in the perspective of quality of process as satisfaction of the users but also, in this case, of the producers. The aim of the proposed study is the valutation and individuation of suitable materials for the improvement of the energetic performances of existing buildings which w…

Issues to be considered for an environmental, economic and social assessment of green roofs by a life cycle approach point of view

2011

Life Cycle Sustainability Assessment al comparto edilizio – teoria e applicazioni pratiche.

2014

Autonomous Robotic Sensing for Simultaneous Geometric and Volumetric Inspection of Free-Form Parts

2022

Robotic sensing is used in many sectors to improve the inspection of large and/or complex parts, enhancing data acquisition speed, part coverage and inspection reliability. Several automated or semi-automated solutions have been proposed to enable the automated deployment of specific types of sensors. The trajectory to be followed by a robotic manipulator is typically obtained through the offline programmed tool paths for the inspection of a part. This method is acceptable for a part with known geometry in a well-structured and controlled environment. The part undergoing assessment needs to be precisely registered with respect to the robot reference system. It implies the need for a setup p…

Study of a Semi Active Electromagnetic Regenerative Suspension

2016

The main objective of this work is the theoretical and numerical study of a device that allows recovering energy from an automobile suspension. In place of the viscous damper, which dissipates the kinetic energy of the vehicle due to rough roads or more marked obstacles, an electromagnetic damper performs the functions of the viscous shock absorber with a recovery of electric energy. The damper has permanent magnets and its working is based on the electromagnetic induction. The used ferromagnetic material is the Supermendur, which has very good ferromagnetic properties, but is expensive and difficult to found, so that the choice of different material is useful to reduce the costs. The mathe…

Design of an Electromagnetic Regenerative Damper and Energy Harvesting Assessment

2016

Design of an electromagnetic regenerative shock absorber is proposed in this paper. In order to increase the efficiency of land vehicles the sources of energy losses have to be eliminated, or reduced. For this reason, several systems, recovering kinetic energy and converting it into electrical power, were studied and designed in the last years. This energy, converted into heat in traditional systems, is recovered to increase the autonomy of the vehicle. The proposed device is constituted by a stator part which coils are placed in an innovative disposition. The moving part is constituted by a rod made in stainless steel with alternated permanent magnets and spacers, so that the relative moti…

Experimental and numerical method for nondestructive ultrasonic defect detection

2010

Ultrasonic methods are well known as powerful and reliable tool for defect detection. Conventional ultrasonic techniques rely generally on piezoelectric transducers where transmission of energy to the material is achieved with contact. In the last decades focus and interest have been directed to non-contact sensors and methods, showing many advantages over contact techniques where inspection depends on contact conditions (pressure, coupling medium, contact area). The growing interest is also due to the further development of air-coupled probes, thanks to new materials for acoustic devices and manufacturing technologies. The use of laser as tool for ultrasonic defect detection is also an eme…