Search results for "STRENGTH"
showing 10 items of 2415 documents
Ornacitrus: Citrus plants (Citrus spp.) as ornamentals
2019
Abstract The industrial production of citrus plants for ornamental use (ornacitrus) began in Italy at the end of the 1960s due to the need for many citrus nurseries to adapt their activities in a time of crisis for citriculture. Nowadays, the ornamental citrus nursery sector is a well-established industry in many European countries such as Portugal, Spain, Greece, and southern Italy. In Italy, nursery production of ornamental citrus plants has become prominent due to the gradual shutdown of many commercial citrus orchards. Currently, Italy maintains its leadership with more than 5.5 million ornacitrus plants produced annually. Ornamental citrus production regards mainly different cultivars …
Climate signal age effects in boreal tree-rings: Lessons to be learned for paleoclimatic reconstructions
2016
Abstract Age-related alternation in the sensitivity of tree-ring width (TRW) to climate variability has been reported for different forest species and environments. The resulting growth-climate response patterns are, however, often inconsistent and similar assessments using maximum latewood density (MXD) are still missing. Here, we analyze climate signal age effects (CSAE, age-related changes in the climate sensitivity of tree growth) in a newly aggregated network of 692 Pinus sylvestris L. TRW and MXD series from northern Fennoscandia. Although summer temperature sensitivity of TRW ( r All = 0.48) ranges below that of MXD ( r All = 0.76), it declines for both parameters as cambial age in…
Lignin Inter-Diffusion Underlying Improved Mechanical Performance of Hot-Pressed Paper Webs
2021
Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing tempera…
Mechanical properties of natural fiber composites produced using dynamic sheet former
2018
Composites formed from wood fibers and man-made cellulosic fibers in PLA (polylactic acid) matrix, manufactured using sheet forming technique and hot pressing, are studied. The composites have very low density (due to high porosity) and rather good elastic modulus and tensile strength. As expected, these properties for the four types of wood fiber composites studied here improve with increasing weight fraction of fibers, even if porosity is also increasing. On the contrary, for man-made cellulosic fiber composites with circular fiber cross-section, the increasing fiber weight fraction (accompanied by increasing void content) has detrimental effect on stiffness and strength. The differences …
Zeolite-silver-zinc nanoparticles : biocompatibility and their effect on the compressive strength of mineral trioxide aggregate
2016
Background This study was carried out to evaluate the biocompatibility of zeolite-silver-zinc (Ze-Ag-Zn) nanoparticles and their effect on the compressive strength of Mineral Trioxide Aggregate (MTA). Material and Methods Biocompatibility was evaluated by an MTT assay on the pulmonary adenocarcinoma cells with 0.05, 0.1, 0.25, 0.5, 1 and 5 mg/mL concentrations of Ze-Ag-Zn. For compressive strength test, four groups containing 15 stainless-steel cylinders with an internal diameter of 4 and a height of 6 mm were prepared and MTA (groups 1 and 2) or MTA + 2% Ze-Ag-Zn (groups 3 and 4) were placed in the cylinders. The compressive strength was evaluated using a universal testing machine 4 days a…
Xyloglucan endotransglucosylase/hydrolase (XTH) overexpression affects growth and cell wall mechanics in etiolated Arabidopsis hypocotyls.
2013
Abstract: Growth and biomechanics of etiolated hypocotyls from Arabidopsis thaliana lines overexpressing xyloglucan endotransglucosylase/hydrolase AtXTH18, AtXTH19, AtXTH20, and PttXET16-34 were studied. Overexpression of AtXTH18, AtXTH19, and AtXTH20 stimulated growth of hypocotyls, while PttXET16-34 overexpression did not show this effect. In vitro extension of frozen/thawed hypocotyls measured by a constant-load extensiometer started from a high-amplitude initial deformation followed by a slow time-dependent creep. Creep of growing XTH-overexpressing (OE) hypocotyls was more linear in time compared with the wild type at pH 5.0, reflecting their higher potential for long-term extension. X…
Fibre extraction from oleaginous flax for technical textile applications: influence of pre-processing parameters on fibre extraction yield, size dist…
2017
International audience; Cultivated primarily for its seeds, oleaginous flax could also be valued for the different fractions that can be extracted from the straw. However, as the straws are not harvested with the same technique and care than for the textile flax, the classical scutching technique cannot be used. As a consequence, an “all fibre” device was used to perform the separation of the different constituents of the oleaginous flax straws. The different fractions were quantified for two retting levels and for two degrees of rewetting of the stems. The physical and mechanical properties of fibres were then evaluated. It appears that the relative amount of fibres extracted from oleagino…
From Norway Spruce Bark to Carbon Foams : Characterization, and Applications
2020
Fresh bark from spruce Picea abies was milled and extracted with hot water. The extracts were purified in a number of steps in order to get tannin-extracts pure enough to prepare tannin-based carbon foams. The chemical composition of the extracts were analyzed. The foams were maturated and thermally treated to obtain desired properties, such as specific surface area, porosity, and compressive strength. It was possible to produce carbon foams even if they contained carbohydrate impurities. Differences in the properties of the carbon foams such as compressive strength, specific surface areas, and pore size distributions might be related to the compositions of the extracts. The foams were fina…
Planting Systems for Modern Olive Growing: Strengths and Weaknesses
2021
The objective of fully mechanizing olive harvesting has been pursued since the 1970s to cope with labor shortages and increasing production costs. Only in the last twenty years, after adopting super-intensive planting systems and developing appropriate straddle machines, a solution seems to have been found. The spread of super-intensive plantings, however, raises serious environmental and social concerns, mainly because of the small number of cultivars that are currently used (basically 2), compared to over 100 cultivars today cultivated on a large scale across the world. Olive growing, indeed, insists on over 11 million hectares. Despite its being located mostly in the Mediterranean countr…
Impact loading history modulates hip fracture load and location : A finite element simulation study of the proximal femur in female athletes
2018
Sideways falls impose high stress on the thin superolateral cortical bone of the femoral neck, the region regarded as a fracture-prone region of the hip. Exercise training is a natural mode of mechanical loading to make bone more robust. Exercise-induced adaptation of cortical bone along the femoral neck has been previously demonstrated. However, it is unknown whether this adaption modulates hip fracture behavior. The purpose of this study was to investigate the influence of specific exercise loading history on fall-induced hip fracture behavior by estimating fracture load and location with proximal femur finite element (FE) models created from magnetic resonance images (MRI) of 111 women w…