Search results for "Scanning electron microscope"

Dielectric behaviour of BaTi1-xZrxO3ceramics obtained by means of a solid state and mechanochemical synthesis

2016

ABSTRACTIn this study the comparison of dielectric behaviour of BaTi1-xZrxO3 (BTZx) ceramic samples prepared by means of a solid state and mechanochemical synthesis was presented. A single phase of perovskite structure was identified in the samples at room temperature. No significant impurities were detected in an EDS spectrum and the samples had a good stoichiometric ratio. The morphology of the investigated samples was characterized by a scanning electron microscopy (SEM). The investigation of dielectric properties of the BTZx samples within the temperature range from 140 K to 600 K was performed by means of a dielectric spectroscopy method at the frequency ranging from 0.1 Hz to 10 MHz. …

Formation of translucent nanostructured zirconia ceramics

2021

Abstract In this work the mechanisms that affect the optical transparency of nanostructured translucent ZrO2 ceramics are studied. The translucent ceramic samples were obtained from a low agglomeration nanosized powder at low pressure and low temperature sintering. Even low pressures cause structural changes and defect creation in the nanocrystals. Annealing was used to study the grain formation, structure and impact of defects. Significant changes in translucency were observed with increase in pore size. In order to further understand the defect creation, the obtained ceramics were doped with Er3+ ions and studied optically. Photoluminescence studies revealed a change in the ratio of green…

Optical studies of MBE-grown InN nanocolumns: Evidence of surface electron accumulation

2009

Stealth dicing with ultrafast Bessel beams with engineered transverse profiles

2017

International audience; We investigate high-speed glass cleaving with ultrafast laser beams with engineered transverse intensity profile. We achieve accuracy of ~ 1 µm at 25 mm/s and drastically enhance cleavability compared to standard Bessel beams.

Effects of cooking on mollusk shell structure and chemistry: Implications for archeology and paleoenvironmental reconstruction

2016

Mollusk shells excavated from archeological sites have been used to reconstruct paleoenvironment, human foraging, and migratory patterns. To retrieve information on past environment or human behavior, chemical signatures such as oxygen stable isotopes (δ18Oshell) are analyzed. Shell archeological remains usually represent food waste. Thermal treatments such as boiling and roasting may influence shell structure and biochemical composition. However, little is known about the relationship between changes at macro-, microstructural and chemical levels. This work is a calibration study on modern Phorcus (Osilinus) turbinatus shells. A simulation of two different cooking methods (boiling and roas…

Lignin Inter-Diffusion Underlying Improved Mechanical Performance of Hot-Pressed Paper Webs

2021

Broader use of bio-based fibres in packaging becomes possible when the mechanical properties of fibre materials exceed those of conventional paperboard. Hot-pressing provides an efficient method to improve both the wet and dry strength of lignin-containing paper webs. Here we study varied pressing conditions for webs formed with thermomechanical pulp (TMP). The results are compared against similar data for a wide range of other fibre types. In addition to standard strength and structural measurements, we characterise the induced structural changes with X-ray microtomography and scanning electron microscopy. The wet strength generally increases monotonously up to a very high pressing tempera…

Spray-Drying Performance and Thermal Stability of L-Ascorbic Acid Microencapsulated with Sodium Alginate and Gum Arabic

2019

[EN] The potential of sodium alginate (ALG) and gum arabic (GA) as wall polymers for Lascorbic acid (AA) encapsulation as a tool for their preservation against the thermo-oxidative degradation was investigated. The influence of such polymers used as wall material on the AAcontent, size, encapsulation efficiency, encapsulation yield and thermo-oxidative stability were evaluated. The AA-microparticles were obtained using the spray-drying technique. An experimental Taguchi design was employed to assess the influence of the variables in the encapsulation process. The microparticles morphology and size distribution were characterized by scanning electron microscopy and laser diffraction. The the…

Direct laser welding of pure titanium to austenitic stainless steel

2018

Abstract Direct butt joining of pure titanium to 316L stainless steel with continuous Yb:YAG laser was performed with variation of the beam offset from joint line. Mechanical properties of samples were evaluated by tensile tests and three-point flexural tests. The fractured surfaces and cross sections of welds were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Tensile properties of welds were strongly determined by the beam offset from joint line and are well described by Weibull statistics. Ultimate tensile strength of 174 ± 69 MPa and ultimate flexural strength of 297 ± 48 MPa were obtained. Brittle fracture took place in…

Impact des conditions d'usinage sur la zone du matériau affectée par le procédé

2007

Colloque avec actes et comité de lecture. Internationale.; International audience; Les procédés d'usinage peuvent créer des contraintes résiduelles à la surface des pièces usinées et ainsi modifier la microstructure et la texture de la matière proche de la surface. De tels changements sont importants pour l'étude du comportement des pièces au cours du temps. Il est alors nécessaire de quantifier les contraintes résiduelles, les composantes de texture et de déterminer la microstructure induite par l'usinage pour comprendre et prédire le comportement des surfaces considérées. Dans cette étude, le matériau cuivre pur a été choisi et considéré comme un "système modèle". En tournage, l'influence…

The effect of photodynamic therapy and polymer solution containing nano-particles of Ag /ZnO on push-out bond strength of the sealers AH-Plus and MTA…

2017

BACKGROUND The aim of this in vitrostudy was to examine and compare the effect of photodynamic therapy and solution containing nano particles Ag/ZnO on adhesion of endodontic sealers to dentinal walls of human root canal. MATERIAL AND METHODS Ninty single-rooted human teeth were selected and their clinical crown was cut from the cemento-enamel junction zone. Canals were prepared by RaCe rotary system and the smear layer was removed using 17% EDTA and 5.25% NaOCl. Samples were randomly divided into two groups of AH Plus and MTA Fillapex based on the sealer type and each group based on antimicrobial method was divided into two sub-groups of photodynamic therapy and polymer containing nano par…