Search results for "Silicide"
showing 10 items of 19 documents
Performance evaluation and stability of silicide-based thermoelectric modules
2020
Abstract Long-term studies on thermoelectric generators based on N-type magnesium silicide (Mg2.01Si0.49Sn0.5Sb0.01) and P-type higher manganese silicide (Mn0.98Mo0.02Si1.73Ge0.02) materials are presented, in the operating temperature range of 200 °C–400 °C. Emphasis is put on the performance and reliability of the current collector configuration, especially on the hot side of the module, and on the thermomechanical stresses that are created during operation and lifetime testing as a result of large temperature gradients experienced across the thermoelectric legs. With silver (Ag) paste as contact material, the long term-stability of the uni-couples was carried out on non-metalized legs and…
Reactive Sintering of molybdenum disilicide by Spark Plasma Sintering from mechanically activated powder mixtures: Processing parameters and properti…
2008
Abstract Dense molybdenum disilicide with a nano-organized microstructure was synthesized by mechanical activation, by producing nanostructured agglomerates of a 1:2 mixture of Mo and Si, followed by the synthesis/consolidation in one step using SPS technology. In order to synthesize a dense molybdenum disilicide with a perfectly controlled microstructure, an investigation of the influence of Spark Plasma Sintering processing parameters (temperature, heating rate, mechanical pressure and holding time) on the chemical composition and the microstructure characteristics has been performed. The present work shows also that the so-obtained materials present better oxidation resistance in compari…
Self-diffusion of silicon in molybdenum disilicide
2004
The self-diffusion of silicon in single crystal MoSi2 was studied by means of a radiotracer technique using the short-lived radioisotope 31Si (half-life ), which was produced and implanted into the samples at the ion-guide isotope separator on-line device at the University of Jyvaskyla in Finland. Diffusion annealing and subsequent serial sectioning of the specimens were performed immediately after the radiotracer implantation. In the entire temperature region investigated (835–1124 K), the 31Si diffusivities in both principal directions of the tetragonal MoSi2 crystals obey Arrhenius laws, where the diffusion perpendicular to the tetragonal axis is faster than parallel to it. In previous s…
MoSi2 laser cladding—A new experimental procedure: double-sided injection of MoSi2 and ZrO2
2003
International audience; In the last decade, development of low density advanced material systems for service at temperatures up to 1300 °C was one of the goals of many researches. This kind of material should mainly have moderate fracture toughness and should exhibit oxidation resistant behaviour at low and intermediate temperature. One of the most studied materials continues to be the intermetallic compound MoSi2. The molybdenum disilicide has been considered as an attractive candidate due to its melting point (2030 °C) and excellent oxidation resistance at high temperatures. The main problem associated with the MoSi2 layer synthesized using laser beam is the layer fragility. To avoid this…
Enhancement of self-sustaining reaction by mechanical activation: case of an FeSi system
1999
Mechanical high energy ball milling of an Fe2Si elemental powders mixture was used to activate a self sustaining combustion reaction or so-called self-propagating high-temperature synthesis (SHS) to form iron disilicide, a reaction for which the thermodynamic criterion is not favorable. A complete characterization of the milled powders before reaction was performed with energy dispersive X-ray spectrometry, specific surface measurements and X-ray diffraction profile analysis. Thermal and structural information describing the combustion front initiated by heating up a sample to 400°C in a Fe‐Si system is communicated. In order to isolate the phases involved in the gasless reaction, a time-re…
Design, assembly and characterization of silicide-based thermoelectric modules
2016
ID: 1143 In: Energy conversion and management, 13-21. Summary: Highlights•Novel silicide-based thermoelectric modules were experimentally investigated.•The modules produced high power of 1.04 W at 405 °C and 3.24 W at 735 °C.•An estimated module efficiency of 5.3% represent the highest reported for silicide systems.AbstractSilicides have attracted considerable attention for use in thermoelectric generators due mainly to low cost, low toxicity and light weight, in contrast to conventional materials such as bismuth and lead telluride. Most reported work has focused on optimizing the materials properties while little has been done on module testing. In this work we have designed and tested mod…
Combustion synthesis of MoSi2 and MoSi2–Mo5Si3 composites: Multilayer modeling and control of the microstructure
2010
International audience; In this work, we present a multilayer modeling for the formation of molybdenum silicides in the exothermic reaction between Mo and Si under the influence of a temperature pulse. The heating rate can either be a well-controlled ramp or be generated spontaneously by the propagation of a combustion synthesis front. The model addresses the specific situation above the melting point of silicon and describes the solid–liquid reaction taking place in a single representative particle of molybdenum surrounded by the melt of silicon. We obtain a set of kinetic equations for the propagation of the interfaces between the different layers (Mo/Mo5Si3 and Mo5Si3/MoSi2) in the solid…
Enhancement of self-sustaining reaction Cu3Si phase formation starting from mechanically activated powders
2000
Mechanical high-energy ball milling of an 3Cu Si elemental powders mixture was used to activate a self-sustaining combustion reaction or so-called self-sustaining high-temperature synthesis (SHS) to form the copper silicide phase, a reaction for which the thermodynamic criterion proposed by Munir for self-propagation reaction is not favorable. A complete characterization of the end-products was performed with X-ray diffraction analysis and scanning electron microscopy. Thermal and structural information describing the combustion front initiated by heating up a sample to 180°C in a Cu:Si system is communicated. This paper clearly shows that the mechanically activated self-sustaining high-tem…
Ohmic contacts on n-type and p-type cubic silicon carbide (3C-SiC) grown on silicon
2019
This paper is a report on Ohmic contacts on n-type and p-type type cubic silicon carbide (3C-SiC) layers grown on silicon substrates. In particular, the morphological, electrical and structural properties of annealed Ni and Ti/Al/Ni contacts has been studied employing several characterization techniques. Ni films annealed at 950 degrees C form Ohmic contacts on moderately n-type doped 3C-SiC (N-D similar to 1 x 10(17) cm(-3)), with a specific contact resistance of 3.7 x 10(-3) Omega cm(2). The main phase formed upon annealing in this contact was nickel silicide (Ni2Si), with randomly dispersed carbon in the reacted layer. In the case of a p-type 3C-SiC with a high doping level (N-A similar …
One-step formation of nanostructures on silicon surfaces using pure hydrogen-radical-initiated reactions
2013
One-step formation of silicon nanowires, sheets, and texture surface on a silicon substrate has been achieved using hydrogen-radical etching reactions. Metallic tungsten and for comparison purposes a tungsten hot wire, were used as catalysts for the hydrogen-molecular cracking. It was shown that a variety of surface structures on silicon such as inverted pyramid texture, V-groove texture, dense silicon nanowire growth over texture, and nanosheet structure can be obtained by controlling the process conditions. The obtained results suggested that the formation of nanotungsten silicide particle is an essential prerequisite to obtain these structures. The particles work as an etching mask again…