Search results for "Simulation."
showing 10 items of 4779 documents
Investigation of thick sheet AHSS springback in combined bending under tension
2012
In this paper, we investigate the springback behavior of several advanced high-strength sheet steels (TRIP, Dual-Phase, ferrite-bainite) with thicknesses up to 4 mm. Samples were tested by means of the bending-under-tension (BUT) test. The BUT has been extensively applied, in the literature, to relatively thin (1 mm and thinner) sheet metals for automotive applications; the applicability of several guidelines from the literature was investigated in this work in the context of thick advanced high strength steel (AHSS) sheets and using a sample width of 12 mm. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for …
A full body musculoskeletal model based on flexible multibody simulation approach utilised in bone strain analysis during human locomotion
2011
Load-induced strains applied to bone can stimulate its development and adaptation. In order to quantify the incident strains within the skeleton, in vivo implementation of strain gauges on the surfaces of bone is typically used. However, in vivo strain measurements require invasive methodology that is challenging and limited to certain regions of superficial bones only such as the anterior surface of the tibia. Based on our previous study [Al Nazer et al. (2008) J Biomech. 41:1036-1043], an alternative numerical approach to analyse in vivo strains based on the flexible multibody simulation approach was proposed. The purpose of this study was to extend the idea of using the flexible multibod…
Take-off aerodynamics in ski jumping
2001
The effect of aerodynamic forces on the force-time characteristics of the simulated ski jumping take-off was examined in a wind tunnel. Vertical and horizontal ground reaction forces were recorded with a force plate installed under the wind tunnel floor. The jumpers performed take-offs in non-wind conditions and in various wind conditions (21-33 m s(-1)). EMGs of the important take-off muscles were recorded from one jumper. The dramatic decrease in take-off time found in all jumpers can be considered as the result of the influence of aerodynamic lift. The loss in impulse due to the shorter force production time with the same take-off force is compensated with the increase in lift force, res…
An integrated model for biological and physical process simulation in membrane bioreactors (MBR).
2011
Abstract Mathematical modelling of membrane bioreactors (MBRs) for wastewater treatment has targeted either the biological processes (treatment quality target) as well as various aspects of system management. However, the high number of interactions among the involved physical–chemical processes, hampers a straightforward mathematical modelling. This circumstance is much more emphasized for submerged MBR systems where the membrane is immersed in an aeration tank. One of the main crucial points that prevents a comprehensive understanding is the interpretation of the fouling phenomenon and its connections with the biological processes. An overall mathematical model for MBR has not been comple…
Visual-based Feedback Control of Casting Manipulation
2006
In this paper, we present a method to control casting manipulation by means of real-time visual feedback. Casting manipulation is a technique to deploy a robotic end-effector at large distances from the robot’s base, by throwing the end-effector and controlling its ballistic flight using forces transmitted through a light tether connected to the end-effector itself. The tether cable can also be used to retrieve the end-effector and exert forces on the robot’s environment. Previous work has shown that casting manipulation is able to catch objects at a large distance, proving it viable for applications such as sample acquisition and return, rescue, etc. In previous experiments, the position o…
DSC: software tool for simulation-based design of control strategies applied to wastewater treatment plants.
2011
This paper presents a computer tool called DSC (Simulation based Controllers Design) that enables an easy design of control systems and strategies applied to wastewater treatment plants. Although the control systems are developed and evaluated by simulation, this tool aims to facilitate the direct implementation of the designed control system to the PC of the full-scale WWTP (wastewater treatment plants). The designed control system can be programmed in a dedicated control application and can be connected to either the simulation software or the SCADA of the plant. To this end, the developed DSC incorporates an OPC server (OLE for process control) which facilitates an open-standard communic…
A Critical Analysis on the Friction Modeling in Orthogonal Cutting of Steel
2007
Numerical simulation of cutting process is today moving towards two different directions. The former concerns the development of high performance codes able to approach the 3D phenomena, the latter is already focused on the study of some fundamental aspects whose full understanding may be strategic for the knowledge enhancing in this very complex field. In the paper this second way was pursued and a wide analysis on the numerical robustness of the 2D orthogonal cutting process is presented. In particular, the role played by the friction modeling is discussed taking into account a wide integrated numerical and experimental campaign.
Multi-objective optimization of nitinol stent design.
2017
Nitinol stents continuously experience loadings due to pulsatile pressure, thus a given stent design should possess an adequate fatigue strength and, at the same time, it should guarantee a sufficient vessel scaffolding. The present study proposes an optimization framework aiming at increasing the fatigue life reducing the maximum strut strain along the structure through a local modification of the strut profile.The adopted computational framework relies on nonlinear structural finite element analysis combined with a Multi Objective Genetic Algorithm, based on Kriging response surfaces. In particular, such an approach is used to investigate the design optimization of planar stent cell.The r…
H∞ static output-feedback control design with constrained information for offshore wind turbine system
2013
Abstract This paper deals with H ∞ static output-feedback control design with constrained information for offshore wind turbines. Constrained information indicates that a special zero–nonzero structure is imposed on the static output-feedback gain matrix. A practical use of such an approach is to design a decentralized controller for a wind turbine. This will also benefit the controller in such a way that it is more tolerant to sensor failure. Furthermore, the model under consideration is obtained by using the wind turbine simulation software FAST. Sufficient conditions to design an H ∞ controller are given in terms of Linear Matrix Inequalities ( LMI s ). Simulation results are given to il…
DETERMINATION AND ANALYSIS OF HEAD AND CHEST PARAMETERS BY SIMULATION OF VEHICLE-TEENAGER IMPACT
2013
This paper reports the results of multi-body numerical simulation of a vehicle crash with a teenager pedestrian. A previous technique utilized for adult pedestrian impact is applied. The work starts with the determination of the masses for the various segments of the body of a teenager with a total mass of 45 kg and then switches to the construction of the dummy and the middle-class vehicle in the Visual Nastran environment. Simulations are performed for both frontal impacts and lateral impacts, when the vehicle is travelling at a constant speed and when the vehicle is braking, following the Euro NCAP rules on the subject. The results are analysed by calculating the values of the head inju…