Search results for "Simulation"
showing 10 items of 5095 documents
Neural modelling of friction material cold performance
2008
The complex and highly non-linear phenomena involved during braking are primarily caused by friction materials’ characteristics. The final friction materials' characteristics are determined by their compositions, manufacturing, and the brake's operating conditions. Analytical models of friction materials' behaviour are difficult, even impossible, to obtain for the case of different brakes' operating conditions. That is why, in this paper, all relevant influences on the friction materials' cold performance have been integrated by means of artificial neural networks. The influences of 26 input parameters, defined by the friction materials' composition (18 ingredients), manufacturing (five pa…
Springback of thick sheet AHSS subject to bending under tension
2012
Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677 The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was investigated by means of the bending-under-tension (BUT) test. The applicability of several guidelines from the literature was investigated experimentally and numerically. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for the non-linear influence of the tool radius was observed. The influence of numerical factors on the predicted values of springback was investigat…
Robust control for high performance induction motor drives based on partial state-feedback linearization
2019
This paper deals with a robust input-output feedback linearization control technique for induction motors. Indeed, classic feedback linearization presents two main disadvantages: 1) the accuracy of the dynamic model; and 2) the corresponding correct knowledge of the model parameters. To address this issue, the linear controller has been substituted with a suitably controller designed to be robust to the variations of the main parameters of the induction motor, like stator and rotor resistances, and the three-phase magnetizing inductance. The proposed controller has been tested both in numerical simulation and experimentally on a suitably designed test setup. Moreover, it has been compared w…
Enhancing tracking performance in a smartphone-based navigation system for visually impaired people
2016
In this paper we show how to enhance the tracking performance of Arianna, a low-cost augmented reality system designed to meet the needs of people with problems of orientation, people with sight impairment and blind people. For augmented reality system we mean the design of: i) a set of paths and tags to be deployed in the environment, realized in various ways depending on the context (decorative elements easily identifiable, colorful stripes, QR code, RFID, etc.); ii) an instrument of mediation between the reality and the user (typically a smartphone) to access the information disseminated in the environment by means of a camera and provide a vibration feedback signal to the users for foll…
Simulación de Plataformas Robóticas de Movimiento para Aplicaciones de Realidad Virtual Mediante Filtros Digitales
2017
[ES] El uso de plataformas robóticas de movimiento en simuladores de vehículos y aplicaciones de Realidad Virtual es relativamente habitual. Sin embargo, el ajuste de los algoritmos que controlan su funcionamiento, denominados algoritmos de washout, no es sencillo y requiere de numerosas pruebas hasta obtener una apropiada fidelidad de movimiento. Disponer de herramientas que permitan simular plataformas de movimiento puede permitir simplificar esta tarea. Es por ello que este trabajo presenta un método para la caracterización y simulación de manipuladores robóticos mediante filtros digitales de segundo orden, sencillo de implementar y ajustar a partir de una caracterización previa. El simu…
Assessment of material models through simple machining tests
2008
The accuracy of the results obtained from FEM simulation of machining operations depends on the accuracy of input data. Among these, the flow stress data of the workpiece are extremely important together with the friction along the tool-chip interface. In this study, an identification procedure for the determination of material parameters that are used for the FEM simulation of machining processes is proposed. The procedure is based on the coupling of a numerical identification procedure and Arbitrarian Lagrangian Eulerian (ALE) Finite Element simulations of turning operations. An experimental campaign was developed in order to calibrate the model and to validate the procedure. The basic id…
Modelling and Simulation of Machining Processes and Operations
2008
This chapter provides the state-of-the-art knowledge engineering and modelling techniques applied in manufacturing/machining and overviews future trends observed at a global scale. Modelling methods for machining processes and operations are classified. The chapter also highlights the multiple tasks of modelling and simulation in modern machining/manufacturing systems. The most popular techniques of numerical simulation including finite difference method and finite element method (FEM) related to mechanical and thermal problems arising in machining processes are described. Practical examples of FE models of various metal cutting operations and their importance in modern manufacturing are pr…
A simulated annealing-based approach for the joint optimization of production/inventory and preventive maintenance policies
2017
Even if more reliable than the past, the performance of modern manufacturing systems is still affected by machine’s deteriorations and breakdowns. As a consequence, adequate maintenance programs must be implemented to adequately satisfy demands during manufacturing stops due to unexpected failures or preventive maintenance (PM) actions. Despite production and maintenance are closely related issues, their joint optimization has become an important research topic just during the last decade. Therefore, the present paper proposes a model for the combined optimization of production/inventory control and PM policies with the aim of minimizing the total expected cost per unit time. The model is f…
Data-based modeling and estimation of vehicle crash processes in frontal fixed-barrier crashes
2017
Abstract As a complex process, vehicle crash is challenging to be described and estimated mathematically. Although different mathematical models are developed, it is still difficult to balance the complexity of models and the performance of estimation. The aim of this work is to propose a novel scheme to model and estimate the processes of vehicle-barrier frontal crashes. In this work, a piecewise model structure is predefined to represent the accelerations of vehicle in frontal crashes. Each segment in the model is corresponding to the energy absorbing component in the crashworthiness structure. With the help of Ensemble Empirical Mode Decomposition (EEMD), a robust scheme is proposed for …
Flexible integration of robotics, ultrasonics and metrology for the inspection of aerospace components
2016
The performance of modern robotic manipulators has allowed research in recent years, for the development of fast automated non-destructive testing (NDT) of complex geometries. Contemporary robots are well suited for their accuracy and flexibility when adapting to new tasks. Several robotic inspection prototype systems and a number of commercial products have been created around the world. This paper describes the latest progress of a new phase of the research applied to a composite aerospace component of size 1 by 3 metres. A multi robot flexible inspection cell was used to take the fundamental research and the feasibility studies to higher technology readiness levels, all set for future in…