Search results for "Solid"

Influence of processing conditions on some properties of anionically synthesized polycaprolactam in presence of lithium chloride

1980

Nylon 6–LiCl systems of various concentrations were prepared by anionic polymerization of caprolactam in the presence of salt. A depression of both crystallization rate and melting temperature was evidenced through x-ray, density, and DSC analyses. Such a preliminary characterization allowed for choosing the proper conditions in order to obtain amorphous fibers from a spinning operation which was performed at a temperature lower than the pure polymer melting point. These results are of technological relevance, especially in view of obtaining, as in similar cases, large amorphous orientations through a spinning–drawing process and high-modulus fibers after subsequent crystallization. Also, t…

Strain rate effect in the single-fiber-fragmentation test

2001

The single fiber fragmentation test (SFFT) has been widely used to characterize the interface in fiber-reinforced polymers. The purpose of the work reported here was to determine the effect of strain rate on the fiber fragment lengths obtained in the SFFT. Three materials systems were used to make single-fiber-composite specimens: E-glass fiber/polycarbonate matrix, AS4-carbon fiber/polycarbonate matrix, and AU4-carbon fiber/polycarbonate matrix. The fiber-matrix adhesion in all three systems is based on physisorption rather than chemisorption. Each system was tested at strain rates ranging over four orders of magnitude. Results are reported in terms of fragment length, the dependent variab…

1982

The stress relaxation behaviour after compression yielding of two semicrystalline polymers, a low density polyethylene and an isotactic polypropylene, is investigated. Data taken at several strains, reached with different sample loading rates, are considered. Master curves are obtained by means of dimensionless stress and time measures, similar to those recently adopted for some amorphous polymers. Die Spannungsrelaxation nach Druckbeanspruchung wurde an zwei semikristallinen Polymeren, Polyethylen neidriger Dichte und isotaktischem Polypropylen, untersucht. Die bei unterschiedlichen Deformationen, welche mit unterschiedlichen Beanspruchungsgeschwindigkeiten erreicht wurdern, erhaltenen Erg…

Calculation of Dependent Elastic Constants of Plastic Foams with a Pronounced Strut-Like Structure

2003

Seven dependent elastic constants of monotropic plastic foams with an expressed strut-like structure are calculated. For this purpose, the basic results of the previously elaborated mathematical model for light-weight plastic foams is used. The model includes a model cell of local structure for monotropic/isotropic plastic foams and an ensemble of structural elements, which allows one to calculate the seven dependent elastic constants, taking into account the pronounced polydispersity of the structure of plastic foams. The numerical values of the constants are compared with the available experimental data, and a satisfactory agreement is found to exist. As a final result, a full set of gene…

Linear–dendritic block copolymers: The state of the art and exciting perspectives

2011

Concurrent with the rapid development of both dendrimers and hyperbranched polymers, a novel class of block copolymer architectures has emerged from the combination of these dendritic architectures with linear chains, the “linear–dendritic block copolymers” (LDBCs). This review gives a comprehensive summary of the state of the art in this rapidly developing field from pioneering early work to promising recent approaches.The different strategies leading to these hybrid architectures with either perfect dendrimer/dendron building blocks or imperfect, yet more conveniently accessible hyperbranched segments, are reviewed and compared. The consequences of the unusual polymer topology for supramo…

Hybrid materials from organic polymers and inorganic salts

1994

The prepaparation of amorphous, homogeneous blends of zwitterionic polymers and transition metal salts was investigated. Homogeneous miscibility was achieved in many cases up to equimolar amounts of salt, depending on the anion and cation chosen. Various analytical techniques point to a solid state solution of the inorganic ions in the polymer matrix.

The glass transition in polymer melts

1994

This paper presents some results of a Monte Carlo simulation for the glass transition in two- and three-dimensional polymer melts. The melt was simulated by the bond-fluctuation model on a d-dimensional cubic lattice which was combined with a two-level hamiltonian favouring long bonds in order to generate a competition between the energetic and topological constraints in the system. This competition prevents crystallization and makes the melt freeze in an amorphous structure as soon as the internal relaxation times match the observation time of the simulation set by the cooling rate. The freezing point of the melt, i.e the glass transition temperature Tg, thus depends upon the cooling rate …

Determination of the conformation of polymers in the amorphous solid state and in concentrated solution by neutron diffraction

1975

Abstract From the coherent neutron scattering on dilute solid solutions of the ordinary polymer within the deuterated polymer, conformation parameters of polymer chains in amorphous solid states can be determined. In this way vitreous poly(methyl methacrylate) (PMMA) has been investigated. The chains form unperturbed coils and the radius of gyration is very near to the corresponding value in dilute solutions of the same polymer in the low molecular θ-solvent butyl chloride. The same principle of measurement has been applied to concentrated solutions of PMMA in D-acetone. The solutions contained 50% polymer, the main part of which (98% and more) was deuterated so that the system was opticall…

Small angle X-ray scattering from amorphous polymers arising from heterogeneities

1973

The small angle X-ray scattering of glassy polymers (PET, PC, PVC, PMMA) and of polymer melts (PE) was studied. The dependence of the intensity scattered at small angles on the sample treatment suggests that neither the inherent structure of the pure polymer phase nor microholes are the origin of the scattering. In agreement with all experimental facts the scattering can be attributed to foreign particles such as for instance stabilizers in the polymer matrix. The consequence of this result is discussed with respect to the nodular structure of the amorphous phase and with respect to structural models of the amorphous phase. The nodular structure is not related to regions of different densit…

Sorption of n-hexane in amorphous polystyrene

2014

Sorption properties of pure n-hexane vapor in amorphous polystyrene (PS) were studied at 298 K by thermogravimetry under controlled vapor pressure. Two sorption-desorption cycles were performed by varying the relative pressure between 0 and 0.91. Mixing of PS with n-hexane resulted in a strong plasticization, which was evidenced by quite significant depression in the glass transition temperature of the polymer as shown by differential scanning calorimetry. Maximum quantity of n-hexane sorbed in the PS at 298 K and at a pressure close to saturation was about 12.4 wt %. The thermogravimetry yielded an isotherm with a strong hysteresis loop, explanation of which was hypothesized with the help …