Search results for "Stainle"
showing 10 items of 100 documents
Influence of residual stress, surface roughness and crystallographic texture induced by machining on the corrosion behaviour of copper in salt-fog at…
2012
International audience; The influence of quadratic stress, crystallographic texture, lubrication and surface roughness generated by superfinish turning on the corrosion behaviour of pure copper was quantified in salt-fog atmosphere. This was done using statistical analysis (Pearson's correlation matrix). Three compounds were found after corrosion tests: atacamite/paratacamite and a black layer (mixture of the lubricant and the salt atmosphere). Surface characteristics were classified according to their decreasing influence on the formation of atacamite/paratacamite as follows: surface roughness and quadratic stress. Lubrication and the crystallographic texture have the lowest influence on c…
Direct laser welding of pure titanium to austenitic stainless steel
2018
Abstract Direct butt joining of pure titanium to 316L stainless steel with continuous Yb:YAG laser was performed with variation of the beam offset from joint line. Mechanical properties of samples were evaluated by tensile tests and three-point flexural tests. The fractured surfaces and cross sections of welds were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Tensile properties of welds were strongly determined by the beam offset from joint line and are well described by Weibull statistics. Ultimate tensile strength of 174 ± 69 MPa and ultimate flexural strength of 297 ± 48 MPa were obtained. Brittle fracture took place in…
Effect of green tea extract on enteric viruses and its application as natural sanitizer
2017
In this work, the effect of green tea extract (GTE) was assessed against murine norovirus (MNV) and hepatitis A virus (HAV) at different temperatures, exposure times and pH conditions. Initially, GTE at 0.5 and 5 mg/ml were individually mixed with each virus at 5 log TCID50/ml and incubated 2 h at 37 °C at different pHs (from 5.5 to 8.5). GTE affected both viruses depending on pH with higher reductions observed in alkaline conditions. Secondly, different concentrations of GTE (0.5 and 5 mg/ml) were mixed with viral suspensions and incubated for 2 or 16 h at 4, 25 and 37 °C at pH 7.2. A concentration-, temperature- and exposure time-dependent response was showed by GTE in suspension tests, w…
Effect of self-etching primer/adhesive and conventional bonding on the shear bond strength in metallic and ceramic brackets
2011
Introduction: Bracket debonding from the tooth surface is a common problem in fixed orthodontics. The aims of the present study were to assess the bond strength and failure sites in two ways of bonding technique, with metallic and ceramic brackets. Material and Methods: One hundred premolars were assigned to 4 groups of 25 each: Group A, metallic brackets/ conventional procedure; Group B, metallic brackets/Transbond XT; Group C, ceramic brackets/conventional procedure; and Group D, ceramic brackets/Transbond XT. Transbond XT composite paste was used for bracket bonding and cured by conventional light-cure device. Specimens were subjected to thermocycling. One week after bonding shearing for…
Influence of the dissolution of MnS inclusions under free corrosion and potentiostatic conditions on the composition of passive films and the electro…
2006
Abstract The influence of the dissolution of MnS inclusions at the OCP value and 400 mV versus SCE on the chemical composition of passive films and the electrochemical behaviour of resulfurized austenitic stainless steel was studied in 1 M NaClO 4 , pH 3, solution using SIMS, XPS, electrochemical impedance spectroscopy and the electrochemical microcell technique. The electrochemical dissolution (at 400 mV versus SCE) of inclusions occurred uniformly along the interface and this process was almost complete after 25 min immersion. A small amount of sulfur was detected on the matrix that exhibited a wide passive range. By contrast, the dissolution process under free corrosion was not uniform a…
SVET, AFM and AES study of pitting corrosion initiated on MnS inclusions by microinjection
2003
As pitting is a random phenomenon, it is difficult to predict where a pit will appear on the surface and consequently the use of local probes is rendered difficult. In this work, a new method to study pitting corrosion on a MnS inclusion on 316L stainless steel is proposed. It consists in modifying locally the chemistry in its vicinity by injecting with a microcapillary an aggressive solution of NaCl, H2SO4 or HCl. Once a pit appears, scanning vibrating electrode technique (SVET) is used to follow the current fluctuations over and around the pit when the metal is polarized at a passive potential. In another series of experiments the effect of local activation of MnS inclusion was studied ex…
Relationships between the Impedance of Oxide Scales on Martensitic and Austenitic Steels and Corrosion Rate in Liquid Lead-Bismuth Eutectic
2004
Abstract The impedance properties (resistance and capacitance) of oxide scales on the martensitic/ferritic steel HT-9 and austenitic stainless steel Type 316L (UNS S31603) were examined during immersion in lead-bismuth eutectic (LBE) using a technique similar to electrochemical impedance spectroscopy. These scales were created by preoxidizing the samples in an air/water vapor environment at 800°C for various times prior to immersion in LBE. Calculation of oxide conductivity for samples immersed in LBE at 200°C for 200 h yielded σHT9 ≈ 4 × 10−7 (Ω × cm)−1 while σ316 ≈ 3 × 10−8 (Ω × cm)−1. The influence of temperature alone gave the anticipated Arrhenius behavior with Ea equal to 0.12 eV, whi…
Kinetics of Sigma Phase Precipitation in Niobium-Stabilized Austenitic Stainless Steel and Effect on the Mechanical Properties
2014
Stabilized austenitic stainless steels are widely used in nuclear and oil industries. The 316 Nb steel grade presented in this study holds a small amount of delta ferrite in the austenitic matrix which tends to transform into sigma phase during prolonged exposures in the temperature range of 600-1000°C. Sigma phase is promoted by ferritic elements such as chromium, molybdenum, niobium and silicon. Time-Temperature-Transformation (TTT) diagram of the δ-ferrite evolution is established thanks to DSC experiments and quantitative metallographic analysis. It is observed that the highest sigma phase formation rate occurs between 800 and 900°C, and that the transformation of ferrite begins after a…
Understanding sigma-phase precipitation in a stabilized austenitic stainless steel (316Nb) through complementary CALPHAD-based and experimental inves…
2014
Abstract Sigma-phase precipitation in a 316Nb “stabilized” austenitic stainless steel was studied through complementary CALPHAD-based and dedicated experimental investigations. Thermokinetic calculations performed using Thermo-Calc (with the DICTRA module) and MatCalc software showed that the sigma phase (σ) precipitated directly at γ-austenite grain boundaries (GB) via a common solid-state reaction when carbon and nitrogen contents fell below a critical threshold. Residual δ ferrite was found to be more susceptible to σ-phase precipitation; this type of precipitation occurred via two mechanisms that depended on the concentration profiles of δ-ferrite stabilizing elements induced by previou…
The use of steel angles for the connection of laminated glass beams: Experiments and modelling
2012
Abstract In the present paper the experimental results relative to three-point bending tests on multilayer glass beams and on semi-rigid connections realised with stainless double web angles are presented and discussed. Small and medium size glass beams were tested and load–deflection curves and crack patterns at failure were recorded. The laminated glass specimens, of equal cross-section, were characterised by three different combinations of annealed float and fully thermally tempered glass plies and different interlayers. Steel joints constituted by double web angles to connect two glass beams were tested adopting several geometrical configurations and using stainless steel bolts preloade…