Search results for "Steel"
showing 10 items of 338 documents
Effect of self-etching primer/adhesive and conventional bonding on the shear bond strength in metallic and ceramic brackets
2011
Introduction: Bracket debonding from the tooth surface is a common problem in fixed orthodontics. The aims of the present study were to assess the bond strength and failure sites in two ways of bonding technique, with metallic and ceramic brackets. Material and Methods: One hundred premolars were assigned to 4 groups of 25 each: Group A, metallic brackets/ conventional procedure; Group B, metallic brackets/Transbond XT; Group C, ceramic brackets/conventional procedure; and Group D, ceramic brackets/Transbond XT. Transbond XT composite paste was used for bracket bonding and cured by conventional light-cure device. Specimens were subjected to thermocycling. One week after bonding shearing for…
Material Substitution for Automotive Applications: A Comparative Life Cycle Analysis
2012
Lightweight materials have become an important strategy in the automotive industry to enable vehicle weight reduction and reduce fuel consumption. However, when developing specific strategies, the overall benefits of any material should be analyzed throughout its life cycle to comprehend energy/environmental differences that arise during its processing and its final use. A key example is aluminum which despite having great potential in the use phase requires large amounts of energy to process. This paper provides a comparison between aluminum and steel utilizing a life-cycle approach. This approach reveals the importance of incorporating a recycling strategy to leverage aluminum’s low-weigh…
Estimation of the fatigue life of high strength steel under variable-amplitude tension with torsion: Use of the energy parameter in the critical plane
2003
Abstract The paper concerns application of the energy parameter, being a sum of the elastic and plastic strain energy density in the critical plane, for describing experimental data obtained in fatigue tests of 35NCD16 steel, subjected to constant amplitude tension-compression, torsion and variable amplitude tension-compression, torsion and combined proportional tension with torsion. It has been shown that the normal strain energy density in the critical plane is a suitable parameter for correlation of fatigue lives of 35NCD16 steel under considered kinds of loading. The critical plane is the plane where the normal strain energy density reaches its maximum value.
Shear models of Rc-encased steel joist beams in MRFs
2019
This study presents the application of different analytical and finite element (FE) models aimed at predicting the shear resistance of reinforced concrete (RC) and reinforced concrete-encased steel joist (HRCESJ) beams with inclined transversal reinforcement in moment resisting frames (MRFs). In particular, four analytical models are taken into account, two of them specifically conceived for HRCESJ beams in seismic area. The analytical models considered are Eurocode-2 model for the shear strength of RC beams; a variable-inclination stress-field approach; a strut-and-tie additive model and, finally, an analytical formulation in which the shear capacity depends on the number of pairs of incli…
Conversion electron Mössbauer study of low carbon steel polarized in aqueous sulfate and sulfite containing sulfate solutions
1993
Abstract The passivation of low carbon steel was studied in aqueous solutions of 0.5 M Na 2 SO 4 (pH = 3.5 and 6.5) and of 0.5 M Na 2 SO 4 + 0.001 M NaHSO 3 (pH 3.5 and 6.5). The used conversion electron Mossbauer spectroscopy (CEMS) with the complementary electrochemical, microscopic and spectrophotometric investigations proved that the presence of sulfite ion induces pitting corrosion. The compositions and thichnesses of the passive films formed during the electrochemical treatments are determined from the conversion electron Mossbauer spectra. γ-FeOOH was found in each case as a major component. At pH = 3.5, the sextet belonging to Fe 3 C appears in the spectra in most cases, and also Fe…
Influence of the dissolution of MnS inclusions under free corrosion and potentiostatic conditions on the composition of passive films and the electro…
2006
Abstract The influence of the dissolution of MnS inclusions at the OCP value and 400 mV versus SCE on the chemical composition of passive films and the electrochemical behaviour of resulfurized austenitic stainless steel was studied in 1 M NaClO 4 , pH 3, solution using SIMS, XPS, electrochemical impedance spectroscopy and the electrochemical microcell technique. The electrochemical dissolution (at 400 mV versus SCE) of inclusions occurred uniformly along the interface and this process was almost complete after 25 min immersion. A small amount of sulfur was detected on the matrix that exhibited a wide passive range. By contrast, the dissolution process under free corrosion was not uniform a…
Prediction of surface treatment effects on the tribological performance of tool steels using artificial neural networks
2019
The present paper discussed the development of a reliable and robust artificial neural network (ANN) capable of predicting the tribological performance of three highly alloyed tool steel grades. Experimental results were obtained by performing plane-contact sliding tests under non-lubrication conditions on a pin-on-disk tribometer. The specimens were tested both in untreated state with different hardening levels, and after surface treatment of nitrocarburizing. We concluded that wear maps via ANN modeling were a user-friendly approach for the presentation of wear-related information, since they easily permitted the determination of areas under steady-state wear that were appropriate for use…
SVET, AFM and AES study of pitting corrosion initiated on MnS inclusions by microinjection
2003
As pitting is a random phenomenon, it is difficult to predict where a pit will appear on the surface and consequently the use of local probes is rendered difficult. In this work, a new method to study pitting corrosion on a MnS inclusion on 316L stainless steel is proposed. It consists in modifying locally the chemistry in its vicinity by injecting with a microcapillary an aggressive solution of NaCl, H2SO4 or HCl. Once a pit appears, scanning vibrating electrode technique (SVET) is used to follow the current fluctuations over and around the pit when the metal is polarized at a passive potential. In another series of experiments the effect of local activation of MnS inclusion was studied ex…
Technical Note:Study of the Cl−-Induced Breakdown of the Passive Layer on Steel
1991
Abstract The Cl−-induced breakdown of the passive layer on a standard steel has an induction time that increases in a nearly linear fashion with the previous holding time (at the passivation potent...
Effect of Plastic hot deformation on the hardness and continuous cooling transformations of 22MnB5 micro-alloyed boron steel
2009
The strains, transformation temperatures, microstructure, and microhardness of a microalloyed boron and aluminum precoated steel, which has been isothermally deformed under uniaxial tensile tests, have been investigated at temperatures between 873 and 1223 K, using a fixed strain rate value of 0.08 s−1. The effect of each factor, such as temperature and strain value, has been later valued considering the shift generated on the continuous cooling transformation (CCT) diagram. The experimental results consist of the starting temperatures that occur for each transformation, the microhardness values, and the obtained microstructure at the end of each thermomechanical treatment. All the thermome…