Search results for "Steel"
showing 10 items of 338 documents
Dissipative connections of rc frames with prefabricated steel-trussed-concrete beams
2020
In the last thirty years, Hybrid Steel-Trussed Concrete Beams (HSTCBs) have been widely used in civil and industrial constructions and, therefore, their mechanical performance must be evaluated with the aim of guaranteeing adequate dissipation of the seismic energy particularly in the beam-to-column joints. However, one of the most frequent peculiarities of HSTCBs is that of using their own steel joist to cover large spans with reduced depth and, in the case of traditional beam-to-column connections, this requires large amount of steel reinforcement inside the panel zone, often made with large diameter rebars. These characteristics make both the panel zone and the beam end potentially vulne…
A study of electrochemically-induced corrosion of low carbon steel in a medium modelling acid rain
1994
Complementary electrochemical, spectrophotometric and electron microsopic investigations were made in addition to the conversion electron Mossbauer spectroscopic (CEMS) measurements to learn more about the mechanism of corrosion of low carbon steel samples in aqueous sulfate and sulfite containing sulfate solutions (pH 3.5, 6.5 and 8.5). Passivation of iron in pure sulfate solution was studied in detail in earlier papers. In the present work, we used a solution containing both sulfate and sulfite anions to obtain more information about the effect of acid rain on low carbon steel samples. The compositions and thicknesses of the passive films formed due to the electrochemical treatments were …
conversion electron Mössbauer study of low carbon steel polarized in aqueous sulfate solution containing sulfite in low concentration
1992
The passivation of low carbon steel was studied in aqueous solution of 0.5 M Na2SO4+0.001 M NaHSO3 at pH=3.5 and 6.5. The found major components at pH-3.5 were: γ-FeOOH and Fe3C, and also FeSO4.H2O could be identified on the surface of the low carbon steel as a minor component. At pH-6.5, the passive film contained only amorphous iron(III)-oxide or oxyhydroxide.
Electrochemical and conversion electron mössbauer study of corrosion induced by acid rain
1993
Abstract The passivation of low carbon steel was studied in aqueous solution of 0.5M Na2SO4 +0.001M NaHSO3 (pH 3.5, 6.5 and 8.5) which can be considered as a model of acid rain. The used conversion electron Mossbauer spectroscopy (CEMS) with the complementary electrochemical investigations proved that the sulfite ions induce pitting corrosion at pH 3.5 and 6 5 while the measurements showed much weaker pitting at pH 8.5. The compositions and thicknesses of the passive films formed during the electrochemical treatments are determined from the CEM spectra. Only γ-FeOOH was found on the surface of the samples at pH 6.5 and 8.5. Nevertheless, at pH 3.5 the sextet belonging to Fe3C appears in the…
Layer formation on silicon steel by processing in H2/H2O at elevated temperatures
1992
Silicon steel (Fe-3wt%Si), as used for transformers and generators, has been annealed in wet hydrogen at elevated temperatures. The composition, sequence, and thicknesses of the layers found by conversion electron Mossbauer spectroscopy (CEMS) and Auger electron spectroscopy (AES) depth profiling for a 10 minutes anneal in different atmospheres are reported. In the range from 500°C to 720°C we observed carbide formation, indicating that the decarburization is hindered. Above 800°C, the layers consist of fayalite or of fayalite and iron oxides, depending on the oxygen potentialaO. At 843°C, the onset of iron oxide formation was found ataO=0.33.
ODS ferritic steels obtained from gas atomized powders through the STARS processing route: Reactive synthesis as an alternative to mechanical alloying
2018
Authors acknowledge ALBA synchrotron (Spain) for the provision of beamtime on the beam line BL22-CLAESS (Proposal 2016081797). Transmission electron microscopy observations were accomplished at Centro Nacional de Microscopía Electrónica, CNME-UCM. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014–2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. Financial support from Basque Government through the ELKARTEK ACTIMAT 2016 project is also acknowledged.
Investigation of precipitate in an austenitic ODS steel containing a carbon-rich process control agent
2018
This work has been carried out within the framework of the German Helmholtz Association and has received funding from the topic “Materials Research for the Future Energy Supply”. The work of M. Parish and Rainer Ziegler is gratefully acknowledged. Thanks are also due to the team of the chemical laboratory at the KIT for performing the chemical analysis. The help of the beamline staff at ELETTRA (project 20140052 ) synchrotron radiation facility is acknowledged. We acknowledge support by Deutsche Forschungsgemeinschaft and Open Access Publishing Fund of Karlsruhe Institute of Technology.
Numerical Modelling for Assessing the Structural Efficiency of CAM® Reinforcement System for Masonry Walls
2022
A large portion of the Italian building heritage is made of masonry construc-tions, which were erected in the first decades of the last century and were conceived to support gravitational loads only. Many research activities have been carried out in order to propose retrofitting techniques aimed at improving seismic behaviour of existing ma-sonry buildings. The present paper focuses on the CAM® reinforcing system. Such a retrofitting technique, which is widely used in Italy, consists in the application of pre-tensioned stainless steel ribbons on existing masonry walls, conferring to them addi-tional strength, ductility and beneficial confinement effects. The preliminary outcomes of a common…
Deformation measurement of circular steel plates using projected fringes
2013
Published version of an article in the journal: The International Journal of Advanced Manufacturing Technology. Also available from the publisher at: http://dx.doi.org/10.1007/s00170-013-5276-3 Fringe projection is a versatile method for mapping the surface topography. In this paper, it is used to measure the deformation of steel plates under static penetration. Here, the surface shape changes continuously. Therefore, it is important to minimize the registration time. To achieve this, we apply a method of fringe location with subpixel accuracy that requires only a single exposure for each registration. This is in contrast to phase shifting techniques that require at least three separate exp…
Iterative Optimal Design of Special Moment Resisting Devices for Steel Frames
2021
Abstract The present paper proposes an iterative procedure devoted to reaching the optimal design of an innovative, recently proposed, moment resisting device. This special device, called Limited Resistance Plastic Device (LRPD), can be utilized, as an example, to equip a steel frame when it is required that the frame must be designed to substitute a masonry panel, i.e., it must be characterized by a structural behaviour as close as possible to the one of the replaced masonry wall. This purpose can be reached by designing the relevant frame imposing appropriate constraints on the elastic stiffness and on the limit resistance. The result can be obtained just by ensuring that the elastic stif…